¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Crestron
  2. Messages
Expanded Topics Messages Polls
Date
Re: Weather App...Again...

 

Hi Joe,
Thanks for the suggestion. I tried it and it didn't work for me (of course...)
still 5 of 6 panels show 'please wait'
the same panel still is working...

Apparently I'm not a good enough programmer to fix what only Crestron can fix...:(
Re: Weather App...Again...

 

I've seen this same "waiting" message after more than one firmware upgrade on TSW-x60s over the last year, but the failure isn't repeatable.? I was able to get the weather app to connect after a power cycling the TSWs after upgrading firmware via the POE switch.? ? ? A reboot was not sufficient.? Not sure if that helps.
Re: In Today's Episode of "Shouldn't that behavior be different...?"

 

¿ªÔÆÌåÓý

That is what I have seen over and over.?


On Jun 29, 2021, at 09:01, Lincoln King-Cliby via groups.io <lincoln@...> wrote:

?

I¡¯ve seen this happen with modules ¨C a signal on an input to (generally bad) or output from (meh) a module may have another driving? source (generally bad) or destination (meh) inside the module ¨C if it does and you put a signal name on the cue in SIMPL but don¡¯t connect it to anything it won¡¯t generate a warning/notice because of the way the compiler inlines modules ¨C the ¡°does this signal go anywhere?¡± check happens, I¡¯m assuming, post-inlining and thus since the signal does go somewhere no warnings.

?

I haven¡¯t seen a native logic symbol? do that, however.

?

I can¡¯t say I¡¯ve noticed any performance problems using signal completion colors ¨C I have seen some behaviors I¡¯d describe as odd when copying and pasting/F9-ing signals under certain less common circumstances but its infrequent enough and mostly self-righting so that it¡¯s not worth trying to report it through normal channels, and not annoying enough to pester back channels.

?

--

Lincoln King-Cliby, CTS, DMC-E-4K/T/D
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Diamond)
ControlWorks Consulting, LLC
Direct: (+1)440.771.4807 | Cleveland: (+1)440.449.1100? | Boston: (+1)508.695.0188 | DC: (+1)202.381.9070? | Fax: (+1)440.449.1106
Crestron Services Provider | Biamp Authorized Independent Programmers | Extron Qualified Independent Programmer

?

From: [email protected] [mailto:[email protected]] On Behalf Of johnh via groups.io
Sent: Tuesday, June 29, 2021 7:56 AM
To: [email protected]
Subject: Re: [crestron] In Today's Episode of "Shouldn't that behavior be different...?"

?

I have actually seen this type of behavior from time to time. I stumble across signals that have no destination/driving yet the program compiles with 0 warnings/errors. Makes me wonder sometimes what else isnt getting picked up? I dont use the signal completion color feature as it seems to slow things down (even more than it alreday is) for me.?

Re: Cox mini box IR Driver - Evolution DMS2344UHDS

 

¿ªÔÆÌåÓý

Thanks

?

From: <[email protected]> on behalf of Philip Pennine <flippen9@...>
Reply-To: <[email protected]>
Date: Wednesday, June 30, 2021 at 8:49 AM
To: <[email protected]>
Subject: Re: [crestron] Cox mini box IR Driver - Evolution DMS2344UHDS

?

I just uploaded it to the FIles section


~phil

Re: Weather App...Again...

 

Anybody seeing continuing issues?
I'm on site with (6) TSW-760 panels, v3.0.14 FW, project compiled with SG in march.
weather app worked then, now 5 of 6 panels showing 'please wait...' again...
Re: Cox mini box IR Driver - Evolution DMS2344UHDS

 

I just uploaded it to the FIles section


~phil
Re: TSR-310 integration with Applehomekit

 

Yes the homekit is enable on the cp3n and i retrieved the home kit code as well.
Cox mini box IR Driver - Evolution DMS2344UHDS

 

Hi All;

Anybody have a driver for this thing that would share it?

TIA
Kol
Re: TSR-310 integration with Applehomekit

 

Do you have Homekit on, on the Crestron processor? I think you need to do it from console on 3 series now and there is a switch on the web portal on the 4 series.
Re: CP4N: sACN traffic goes to control subnet, I need it on LAN port...

 

All of the sACN projects I've done have used a node with a non-multicast address in the standard class C, B, or A IP address ranges.?
While the traffic may be sent multicast, the node you're controlling shouldn't solely have a multicast IP address. There should be a "control" IP address, similar to NVX.
We have used the DMXKing units as well as Chauvet DMX-AN and the Net-X. All three have standard class C, B, or A IP addresses.?
The CP4 should be smart enough to route traffic to the correct port based on the IP range. So if your LAN port is 192.168.x.x and your control subnet is 172.16.x.x, if the node's control IP is on 192.168.x.x, it should send from the correct port.?

Maybe I'm missing something major here.?
Re: TSR-310 integration with Applehomekit

 
Edited

Were you able to pair the processor with home app? Mine is stuck on loading when i add an acessory. The app cant seem to locate the crestron bridge.
I have been trying to control Apple TV through Siri via the TSR-310 microphone.
Re: TSR-310 integration with Applehomekit

 

This is the document i have been following.
Is there some other guide as well?
Re: TSR-310 integration with Applehomekit

 

IMHO it¡¯s totally unreliable. I spent ages trying to get it to work then it fails. TB don¡¯t really have a clue, so the general consensus is IR then CEC (depending on the setup). Many forums on FB discuss why Crestron cannot make this work reliably like other control systems, but to no avail. Be careful if rolling this out to clients - that¡¯s all I¡¯m saying.?
Re: Reliable Pool Control

 

I'll shout for Caleb and ControlWorks as well!!? Love to work with them!!!
Re: Multiple mobile apps on processor

 

I think its the Toolbox version that determines this. older versions required clicking a checkbox to enable multiple projects to be loaded, like Ryan said.
The latest version (v3.09.3) and a few versions before this eliminated this 'feature'.
But still with the internal memory, I have only been able to load up to three projects. If you need more than that, perhaps loading to an SD card might facilitate this...
CP4N: sACN traffic goes to control subnet, I need it on LAN port...

 

Hi!

I use the CP4 control port for NVX network. On the lan port there is a DMX unit i need to control with sACN.
My problem is that the sACN traffic is going to the CP4 control port and not to the lan port.
sACN is multicast and that may be the reason why it is routed to the control port (NVX multicast network port).

Do anyone know if it is possible to route the UDP socket in the simpl+ file to the lan port and not control port?
The multicast address is?239.255.0.44:5568

Erik :)
Re: Multiple mobile apps on processor

 

I forget what instances it occurs (I checked my CP3 and I dont have it), but on the Web Pages and Mobility screen, there is a check box to allow more than one project.? If checked, uncheck that.
--
Ryan Baldwin
CEO | XS Design Studios
rbaldwin@...
760.712.2240
Multiple mobile apps on processor

 

Hi, this is probably a really simple thing, but I have never had to do it before.?

I need to load different iPad GUIs onto the processor for iPads to connect to, rather than storing projects locally on the iPad(s). Default behaviour is only one mobile project in the processer memory, i.e. uploading a new file deletes the old one.

Is it possible to have more than one mobile project stored on the processor (CP3) and if so then what is the process?

TIA
Re: Looking for some lighting programs written in 2013 for a client.

 

It might also be worth contacting Crestron, that number may be the Crestron lighting project number...
Re: Looking for some lighting programs written in 2013 for a client.

 

Not one of mine, but that filename looks similar to ones I've had from Riordan Brothers, they seem to do a lot of lighting programming for Crestron, certainly in the New York area
14581 - 14600 of 256344