Re: Pentair Screenlogic

#237892

Forgive my ignorance here, Im Googling ‘Compool integration adapter’ and nothing is jumping out at me. ?Pool controllers seem to be my Kryptonite. ?The pool guy onsite is useless and Pentair tech support is telling me ‘no home automation’. ?The old Compool setup that was previously there had a header right on the board for RS485 I believe and worked pretty well for years.

Ultamation AppleTV MediaRemote Version Connection Issues (after power loss)

#237891

I've been having an issue with my Ultamation AppleTV module (version 2.12, the latest) not reconnecting to my AppleTV after everything comes back up after a brief power loss.? My PRO3 and main network switch are on a UPS that can handle somewhat lengthy outages (an hour or 2), but the remote switch my AppleTV connects to and the AppleTV itself are not. The AppleTV boots back up fairly quickly after a power loss, but the switch (a HP ProCurve 24 port switch) takes a minute or so to get back up and running.? Frequently after a short power loss where the remote switch and AppleTV lose power, I have to reboot the PRO3 in order to get control back for the AppleTV.? The Ultamation module has a connection status output, but I don't believe there's a way to tell it to reconnect.

Has anyone else run into this and are there any recommended solutions (other than putting a UPS with unlimited capacity on every device in the house...)?

Thanks,

Geoff

Re: Whole House surge and Equipment Power Conditioner

#237890

We use WattBox with OVRC built in. ?A nice web interface for checking status, voltage and wattage for each outlet, scheduled reset etc. ?A large variety of configurations, from strips to rack mount, and a perfectly functioning Crestron module ready to go for integration.

Re: Issues with Sonos & Crestron

#237889

No IP address entered in SIMPL?

Re: Issues with Sonos & Crestron

#237888

Well, it looks like I need to issue an apology.? The reason the new firmware didn't work was caused by the fact that my program for slot 2 was not auto creating an IP table entry for the Intersystem Communications module.? I was able to fix it by manually adding the table entry.? On that note, anyone have an idea why the program that I put into the program 2 slot would not auto create the entry?? Any guidance would be greatly appreciated.

Thanks,
DAVE

Re: Pentair Screenlogic

#237887

开云体育

The IntelliTouch is compatible with the iLink Adapter, and we have a module for that.?

?

The IntelliCenter, uses a different module/license but we have one. ?

?

Neither of those modules will work with EasyTouch. If you want to integrate the EasyTouch system, you need to install the Compool adapter and then you can use the Compool module from the Crestron database.

?

?

Show quoted text

From: [email protected] <[email protected]> On Behalf Of AVMaster
Sent: Friday, October 23, 2020 16:19
To: [email protected]
Subject: Re: [crestron] Pentair Screenlogic

?

Yes we have acquired and used the ControlWorkS module many times in the past but Pentair is telling me that EasyTouch is not compatible with home automation. ?I wanna say we’ve always used the CW module via RS232 and the iLink protocol adapter. ?It’s unfortunately a long drive away and I’m going to have to figure this out onsite and I’d like to get my ducks in a row so that I can make it home before dark...:)

Whole House surge and Equipment Power Conditioner

#237886

What is the consensus on whole house surge at the electrical panels and equipment rack. Additionally, Power Conditioner at equipment rack as well.

I have use APC, Tripplite, Monster, Leviton, Panamax and Cyberpower.

Any other suggestions would be appreciated. Ideally I would like to monitor via Crestron.

Is Richard Gray Power Company still in business and if so is it worth the money?

Re: Pentair Screenlogic

#237885

Yes we have acquired and used the ControlWorkS module many times in the past but Pentair is telling me that EasyTouch is not compatible with home automation. ?I wanna say we’ve always used the CW module via RS232 and the iLink protocol adapter. ?It’s unfortunately a long drive away and I’m going to have to figure this out onsite and I’d like to get my ducks in a row so that I can make it home before dark...:)

Re: Pentair Screenlogic

#237884

Yes, you can control this with a ControlWorks module from their website. Works pretty well, just got to buy the license from them

Re: Pentair Screenlogic

#237883

Sorry to unearth an old thread...I’m being asked to integrate an EasyTouch Compool to ?EasyTouch panel. ?They are currently using the Intellitouch ScreenLogic2 app for control. ?Can you point me in the right direction as to what they need for integration with Crestron? ?The old Compool had RS485 right on the board if I remember correctly. ?The new setup does not. ?I hate pool controllers btw...:). ?Everyone’s setup always seems to be radically different from the next. ?Thanks in advance.

Pentair

#237882

Hey guys and gals, ?I occasionally come across Pentair pool controllers with pretty sophisticated setups. ?We almost always integrate with basic functionality and have them refer to the app for advanced operation. ?The app is Screenlogic2. ?I’ve tried in the past to figure out if there is a URL scheme to launch this app via a button press but never figured it out. ?Anyone know what it might be? ?And yes...I believe I’ve tried all the obvious ones.

Re: Crestron RMC3 with Cisco Touch 10 and Codec Pro

#237881

Does the Cisco codec need to be registered first??

I haven’t registered it yet as I was only testing the unit before it goes to site?

Re: VTPro issues

#237880

Nice!? Learn something new all the time.

Re: VTPro issues

#237879

If you're doing this, it's useful to set the Digital Join field as the "Quick Assign" field (that's the one with the lightning bolt by it).? That way you can just double-click a button and type the join number.? Do so by pressing Ctrl-Q while the Digital Join field is highlighted.? You can do the same thing to set it back to the Label field when you're done.? One of the most useful and least intuitive features in VTPro!

Show quoted text

On Fri, Oct 23, 2020 at 2:17 PM Steve Kuehn <steve@...> wrote:

Yes I find this very annoying too.? However, at least with the last project I did, I found it was quicker just to edit each button individually which didn't move them around then using the click assign feature and then having to go back and move the buttons back in their proper position.

Re: Crestron RMC3 with Cisco Touch 10 and Codec Pro

#237878

开云体育

Hi,

On the Codec make sure that you have enabled SSH, the user has integrator privelidges en the user doesn’t have to “update password after first login” enabled. The SSH public key will be provided by the codec after successfull log on.

Mahalo,

Patrick Soesman

Tel: +31-6-38169901

Email: Patrick@...

Show quoted text

Op 23 okt. 2020 om 18:47 heeft Audvizer <Audvizer@...> het volgende geschreven:

?
Hi,

I was wondering if anyone has ever used a setup with a processor and the Crestron Cisco Touch 10 module from the Application Market??

I’ve added a button to the touch 10 with the name Display Power and ID Display Power.?

I’ve then used the Widget Paramater ID as named above.?

I was wondering where I get the Unique ID from in the SSH part of the module??

It seems like I’m not connecting at all to the processor though.?
I’m receiving a SSH Invalid Parameter\x0D\0A string from the codec.?

This is my first time dealing with Cisco as we normally use Polycom Codec etcs.?

is there something on the codec back end that needs to be switched on or where do I find the Unique ID?

Re: VTPro issues

#237877

Yes I find this very annoying too.? However, at least with the last project I did, I found it was quicker just to edit each button individually which didn't move them around then using the click assign feature and then having to go back and move the buttons back in their proper position.

VTPro issues

#237876

So today, I am converting a non SG for use on a TMPC-V12 running the SG firmware for a client.? Is it just me or does VTPro get worse with each update!? I created a page with a ton of buttons and want to use the click assign digital.? When I try this my buttons move all over the place, even though they are locked.? I go into project defaults and uncheck SHOW GRID and SNAP TO GRID but it doesn't go away.? Unlock all the buttons and highlight them to uncheck SYNCHRONIZATION and that doesn't work either.? WTF CRESTRON!? Does anyone know what version of VTP that I can roll back to that would fix these issues.? Just plain F'n aggravating.

File /IR Drivers/Flirc FireTV (Oppo Commands).zip uploaded #file-notice

[email protected] Notification

#237875

The following files have been uploaded to the Files area of the [email protected] group.

/IR Drivers/Flirc FireTV (Oppo Commands).zip

By: gablerjohn

Description:
Flirc Profile with IR Driver for FireTV

Re: Is Crestron App able to send Push Notifications to iOS/Android?

#237874

Have used Jay's prowl module several times.? Works like a champ and is well worth the $100!

Re: Amazon Fire TV Cube IR File

#237873

Done