¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Bpq32
  2. Topics

BPQ32 IP Gateway to a PiLinBPQ System

 

Will? adding the NAT 44.135.101.2? 192.168.9 line into IP Gateway settings on my BPQ32 system allow outside connections to a PiLinBPQ system on the same network?

Also added the following to IPGatway Settings in PiLinBPQ system;
IPAddr 44.135.101.2
IPNetmast 255.255.255.248
IPPorts 1

If so, are there IP Gateway settings required for the PiLinBPQ system?? Haven't been able to get it to work....

Thanks,
Harmen VE3EMA
 

¿ªÔÆÌåÓý

At the moment I can ping 44.135.101.1 over the IPIP tunnel, but not 44.135.101.2. What is 44.135.101.1?



LinBPQ will add a NAT entry from 44.135.101.2 to the IP address of the machine running LinBPQ.

To allow access from 44 net? to other machines on the same network you need to allocate another address in your 44.35.1.101 range to each and add NAT lines. For example I have

?NAT 44.131.56.2 192.168.1.35
?NAT 44.131.56.4 192.168.1.64
?NAT 44.131.56.5 192.168.1.118
?NAT 44.131.56.6 192.168.1.254

My IPADDR is 44.131.56.7 and the linbpq pi is 192.168.1.44, so I end up with

nat

POGO4:G8BPQ-9}

44.131.56.2 to 192.168.1.35

44.131.56.4 to 192.168.1.64

44.131.56.5 to 192.168.1.118

44.131.56.6 to 192.168.1.254

44.131.56.7 to 192.168.1.44 via TAP

ping 44.131.56.4

POGO4:G8BPQ-9}

OK

Ping Response from 44.131.56.4



73,

John



On 01/07/2022 22:47, Harmen Minnema wrote:

Will? adding the NAT 44.135.101.2? 192.168.9 line into IP Gateway settings on my BPQ32 system allow outside connections to a PiLinBPQ system on the same network?

Also added the following to IPGatway Settings in PiLinBPQ system;
IPAddr 44.135.101.2
IPNetmast 255.255.255.248
IPPorts 1

If so, are there IP Gateway settings required for the PiLinBPQ system?? Haven't been able to get it to work....

Thanks,
Harmen VE3EMA
 

44.135.101.1 is the IPGateway on VE3KPG running BPQ32
44.135.101.2 is VA3HIP running PiLinBPQ

I am unable to ping 44.135.101.2 as well. In fact, I cannot ping any addresses other than 44.135.101.1, but NAT and IPR does seem to be working.

nat
PETERB:VE3KPG-2}?
44.135.101.2 to 192.168.1.9
44.135.101.1 to 192.168.1.10
?
ping 44.135.101.1
PETERB:VE3KPG-2}?
OK
Ping Response from 44.135.101.1
?
ping 44.135.101.2
PETERB:VE3KPG-2}?
OK
?
ping 44.131.56.2
PETERB:VE3KPG-2}?
OK
?
ping 44.92.35.1
PETERB:VE3KPG-2}?
OK
?
ipr
PETERB:VE3KPG-2} 765 Entries
44.0.0.0/9 0 T 0 0 encap 169.228.34.84
44.0.0.1/32 0 T 1 3355 encap 169.228.34.84
44.2.0.2/32 0 T 1 3355 encap 98.20.210.138..........etc..

This is what I have for my IPGateway on VE3KPG;
IPGATEWAY
Adapter \Device\NPF_{EA2D9183-0C8D-4AB0-BD03-AEA6D347354B}? ? ? ? ; See Below Description
44ENCAP 192.168.1.250? ? ? ? ? ? ? ? ? ? ? ; This is a Un-used but inside of routers DHCP (Must be added to routers DMZ)
IPAddr 44.135.101.1? ? ? ? ? ? ? ? ? ? ? ? ? ? ?; Your 44 AMPR IP
IPNetMask 255.255.255.248? ? ? ? ? ? ? ? ; The 248 (last 3) depends on how many IP addresses you have, mine is 8 IP¡¯S
IPPorts 1? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?; Port Numbers to be used, 2 is my AXIP 3 My Telnet port
NAT 44.135.101.2 192.168.1.9? ? ? ? ? ? ?;VA3HIP running PiLinBPQ
ROUTE 44.0.0.0/9 169.228.34.84 T? ? ?; This Line and following line is needed to access the AMPR Portal Web Site
ROUTE 44.128.0.0/10 169.228.34.84 T
**** ; End of Config

This what is setup on VA3HIP;
IPGATEWAY
IPAddr 44.135.101.2? ? ? ? ? ? ? ? ? ? ? ? ?; VA3HIP
IPNetMask 255.255.255.248? ? ? ? ? ? ; The 248 (last 3) depends on how many IP addresses you have, mine is 8 IP¡¯S
IPPorts 1? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ; Port Numbers to be used, 2 is my AXIP 3 My Telnet port
**** ; End of Config

Should I be able to ping any IP address including 44 AMPRNet?

1 - 3 of 3