开云体育

I have a number of refurbished KAM+ TNC's that I will be listing on EBay this month, by refurbished, they have been recapped, firmware updated to v8.2, RTC added, and ram upgraded to 128k/512k see

Thank you! From: "[email protected]" <[email protected]> on behalf of "Jeff, NC6J" <nc6j@...> Reply-To: "[email protected]" <[email protected]> Date: Friday, July 8, 2022 at 12:02 AM To:

Thank you! Appreciate and will see if I can get this working over the weekend. From: "[email protected]" <[email protected]> on behalf of Joshua KJ7LVZ <joshuajayg@...> Reply-To: "[email protected]"

This is my whole direwolf.conf: ADEVICE pulse ACHANNELS 1 CHANNEL 0 MYCALL NC6J-5 MODEM 1200 1200:2200 TXDELAY 40 TXTAIL 10 AGWPORT 8000 KISSPORT 8001 FIX_BITS 1 AX25 MAXV22 1 LOGFILE dwolf.csv and

Oh, and I left out my PTT config line from the instructions because from what I understand, the Signalink uses VOX.? If I'm wrong, we can discuss that.

I could dump a whole config file on you but with direwolf there are only a few things that matter. Identify your soundcard (card 2, device 0) Only one audio channel Everything below this will be

Yes. card 2: SIGNALINK [USB AUDIO CODEC], device 0: USB Audio [USB Audio] Subdevices: 0/1 Subdevice #0: subdevice #0 From: "[email protected]" <[email protected]> on behalf of Joshua KJ7LVZ

I don't use a signalink? but it is just a USB soundcard as far as I can tell. Do you know how to identify your soundcard device number in Linux?? I use "aplay-l" and "arecord -l"

Hi All! I am lost in the configuration rabbit hole, and I feel the Mad Hatter sneaking up on me (I hope someone gets the reference). Does anyone have a configuration file for Direwolf and bpq32 that

Since the introduction of the node wildcard search the command to check “nodes via” is now returning “Missing Call” instead of a list of nodes. Checked on any node on an earlier v6.0.22.x and

Hi Jeff Thanks for the backup, my only point is Kantronics wants 19200 for Com speed on their Dual Port TNC’S, even if it works at 9600 BAUD Com Speed I have helped several in the past with problems

John, Solved! I was running in the Single Window (Term + Mon) mode. When I use the Tabbed mode, it works. In the Single Window (Term only) mode it works also ok. Only Single Window (Term + Mon) mode

I'll look into it when I have a bit of spare time. Thanks, John

Are you running in Single Terminal Mode? If so it looks like the window is being allocated as the AGW monitor window, so connect is disabled. I'll look into it, but in the meantime if you enable

John, I'm sure it's a trivial matter but that doesn't quite gel with what I'm observing. The only RPR station in this list is W7BMH but I see dots next to K7SKI and KB9KC (both HFP stations). Could it

In non-ax.25 drivers (but including UZ7HO) + is connected and ! is heard. For ax.25 . indicates robust packet, no character normal packet. 73, John

This version (QtTermTCP 54) compiles from source and runs ok on gentoo linux. I have KISS in the setup menu but when I select AGW, I can not connect to a station because the connect menu is gray and

Jeff, Thanks for the info. Indeed I'm using the Tracker hostmode driver. I wondered if it was something to do with stations being heard in HFP vs RPR (I use the switchmodes command). Brian W7BMH is

We have used the following for years on our 9612+ ports but run 9600 RF on ours so 19200 serial makes sense. I think the always use 19200 serial comes from an old serial timing issue the KAM-XL's had

Not only that Lee, I have used mine on 9600 baud packet for 20 years and it works just fine.? The KPC 9612 has a significant buffer and never has a problem. Jay WS7I