开云体育

Hi, the rusty connector diagnosis makes sense; I had a similar problem avec water in the control cable connector. I dried it out and then sealed the area with putty and then wrapped it with

Converted from Rich TextThanks for the replys from Clive, and Kyle. Have been out of town this weekend, but I think I found the problem: Took the tape off the end of the control cable at the tuner

I had almost similar HVSWR and thought it was the rig. Then I checked the tuner and later noticed that the control cable looked rusty. I reinserted the cable and also reset the tuner. All's well

Converted from Rich Text hi Dave, i've been using fc-40 over a year. no probs. I'm assuming you've checked ground and the coax hasn't gone o/cct....to the tuner I mean, cos y'd have poor rx,

I installed the FC-40 in my truck after getting it at Orlando, the 857D had been in the truck for several months. Installation went OK, tuner seemed to tune OK on all bands from 60M down. A few weeks

The local dealer finally got my money for a new one. Now it's time to play with some wires. Thanks to all, Dave VA2DV

When are you going to learn not to get rid of anything? Hee hee. va2dv <va2dv@...> wrote: I am looking for a clean,near-new condition FC-40 remote tuner. I have sold mine in a recent trade-in

I am looking for a clean,near-new condition FC-40 remote tuner. I have sold mine in a recent trade-in and miss it a lot. Maybe someone got one in the recent promotion and dont plan to use it ? Let me

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the YaesuTuner group. File : /antennal.JPG Uploaded by :

I just found out my FC 30 tuner for my 857D will work with my FT100D as well as the FC20.Any one know what other yaesu auto tuners will work with these two radios other than the FC 40?

Clive, an FT-857D is installed in my car and I used the FC-40 with it stationary. I can not find any functional differences to the FT-897. The FP-30 is very compact, installed into to the FT-897,

Hanno, the control cable from the FC-40 to the FT-897 was a home made, 10m long. I installed clap-on ferrites at both ends near the plugs, not sure if they were necessary, but no problem with

Converted from Rich Text hi Jurgen., i'm intrigued to hear more of your experiences with the 897 and to compare with 857D.... I guess you have a key advantage with that built-in power supply.,

Jürgen, Very interesting... I also look forward to test my setup with the FC40, the Spieth pole and one of the radios FT 857 or / and 897. During summer vacation. Do you have extension cable for the

Dear all, I am just back from a vacation to 3B8, Mauritius and want to share my experience with the FC-40: I had a small bungaloo with space for an antenna and checked this in advance with the

http://ph.groups.yahoo.com/group/YaesuTuner/photos/browse/3625 photos posted. Will add better ones as soon as I can showing more detail, these are done in a 5mins break!

Hi Kyle, sorry long delay - work issues in the office - Basically, connect a balanced feedline (openwire, ladderline) but NOT coax to the ATU. One side to the wire connector, the other to ground. I

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the YaesuTuner group. File : /hamadf.exe Uploaded by : ab9lx

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the YaesuTuner group. File : /mh-59a8j.pdf Uploaded by : kc9anq

The FC-40 is a wire tuner. what are you doing with the other side of the 300 ohm line? Clive <l81ker@...> wrote: Hi folks, after moving to FINLAND where its very cold now, I put up a