开云体育

Hi Guy's n Gals. I recently purchased a FL-7000 & was wanting to interface it with my FT-847. Was wanting to know if anyone has interfaced their FT-847 with a FL-7000 & could let me know the

Oops, forgot the 2.2k in the upper diagram! See the revised circuit, attached. Greg KO6TH Greg D via groups.io wrote: Hi Rob,

Hi Rob, I've not found the need to have an isolation transformer, but yes, DC blocking is needed to keep the rig from going into transmit. If you don't have a transformer the

Sorry skip that…… I just couldn't decipher that on a mobile phone …. So small. There should also be a 2k resistor if the equipment uses and external PTT and does not reply on the high side

I don’t see a 10uf capacitor in the FSK out lines? De Spence G5STO Sent while portable! please excuse typos.

Afternoon all , Checking my understanding of a perceived challenge here with you all: before buying the bits and prototyping a cable... It seems that plugging the 847's rear 3.5mm data jack into

thanks Greg. I figured that would be the case as effectively its still SSB just via a different pathway, but always better to confirm with others. audio is DEFINITELY getting to the rear of the 847

If you're driving the radio too hard it can have a similar effect, drop your TX line out level going to the radio by 80% and see if it transmits but with low levels then gradually bring it up for a

If it's actually going into transmit, I'd check your audio path. The meter should deflect at least a little, showing the transmit power. Greg KO6TH Rob MW0CQU

Hi All, A dumb question perhaps on the surface, but when transmitting AFSK data via the rear port of the 847 And not using CAT mode for PTT (as I gather CAT mode expects mic audio through the mic

Yes I can hear FT8 tones through the speaker if I turn volume up. If I turn on MONI I can hear my TX tones too. There is just NIL on RX 73 Pete G4RRM

Ok, yeah, puzzled here too.? You might try picking the receive audio off the DIN connector (packet, pins 5 & 2) just to see if it's present there.? That might help isolate what's happening.? I

Hi Greg Yes use CAT and the PTT test function in WSJT worked (red) and the radio Tx's (ssb-data) My TX works its the lack of ANY rx that's the issue. As I said in my mail, I have swapped the FT5000

Audio routing on the 847 is fixed, so a grayed-out config button is correct.? Receive audio goes to all the ports (Data, DIN, and the speaker), but transmit audio source is dependent on the mode and

Hi All Thanks for adding me to the group. I have a problem with my FT847 when trying to run FT8 on VHF. I have been using the FT847 to run 2m FT8 with a G4ZLP interface into the Data jack on the

Hi all, I have a strange problem with an FT-847 and hopefully someone has seen this before and can help:? I have an FT-847 that works fine EXCEPT for an issue with turning it on or off. I replaced

*PRICE REDUCTION!!!! NEW PRICE $42 + $6 SHIPPING (us)* Hello, Up for sale is an Yaesu DSP Board for FT-847. This is the original Yaesu DSP Unit. It has been tested working. I no longer have a use

It appears my advert has caused members some sort of irritation, I have therefore deleted it and the comments posted. May I suggest that if you have nothing constructive to say, don't. Leighton

I've decided to part with my 847. Ser. # 3G760154. It is in great condition. Everything works as new. Looks nearly new also. I have the original manual, power cable and hand mic. Also included is the

Hi, I do have 847 and a Digimode-4 interface (the one for the 847), what is the setting needed on the 847 and PC (Wxjt / Jtdx)? to make it run? Thanks Nimrod 4X1BG