Re: ADMS-1J has been SOLD
The ADMS-1J programming kit has been sold.
73, Jim K5JG
toggle quoted message
Show quoted text
On 7/12/2016 9:22 PM, Jim K5JG wrote: I have the following FT-60R accessories for sale:
1 - RT Systems ADMS-1J Programming Software (with installation key) &
USB Cable all in the original box.
|
Re: FT-60 Possible Problem- suggestions?
Yes! Thank you. ? The FT-60 transmits fine on the stock? E-DC-5B car cig lighter charger cord. Voltage reads 12.4 volts on the FT-60. ? I have two stock FNB-83 battery packs that are fully charged neither of which seem to work for transmitting as described and both of which measure 8.4 volts in the FT-60. So I guess the assumption is these batteries are somehow non-functional even though the battery voltage/indicator appears ok. ? The other issue is the problem might be with my CD-29 Drop-in Charger although I don't know how since the charging cycle appears normal with red LED changing to green after cycle ends. ? ? I guess the plan would be to obtain a new FNB-83 battery pack and try that for transmitting. ? Thanks for the assistance. Hank? KB1JLA ?
toggle quoted message
Show quoted text
From: FT-60@... [mailto:FT-60@...]
Sent: Tuesday, July 12, 2016 10:07 PM
To: FT-60@...
Subject: Re: [FT-60] FT-60 Possible Problem- suggestions?? ? Sounds like a bad battery or you are trying to transmit while charging. Plugged into a cigarette lighter plug will work, the wall wart won't.?
Jardy Dawson WA7JRD Sent from the Death Star for Darth Vader's eyes only. Any other reception will be severely punished. ? ? Encountering a problem in programming my FT-60. ?After entering a frequency (frequency+tone+tone freq.) ?and storing it in memory channel #2 (for example) any attempt to transmit on that channel results in FT-60 shutdown (power off to blank screen), and reboot to startup screen with audible beeps, 'MEMORY', ?battery voltage value and then contents of memory channel 2 showing on screen. ? I have tried a complete reset (F4 ALLRST). I have tried programming manually and via software. ? All receive functions are fine. I can receive ham bands, public safety, weather channels, etc. Battery functions are fine. ? This FT-60 has worked fine in the past, but has been out of service for a couple of years and simply stored carefully. ? Any suggestions as to the problem transmitting would be appreciated. Thanks. ? Hank? KB1JLA
|
Re: FT-60 Possible Problem- suggestions?
Correct. Programing local ham repeaters. ?
toggle quoted message
Show quoted text
From: FT-60@... [mailto:FT-60@...]
Sent: Tuesday, July 12, 2016 11:10 PM
To: FT-60@...
Subject: RE: [FT-60] FT-60 Possible Problem- suggestions?? ? We are assuming that you are loading a freq within the ham bands, right?
-------- Original message --------
From: "'hank' hanklane@... [FT-60]" <FT-60@...>
Date: 12/07/2016 16:39 (GMT-07:00)
To: FT-60@...
Subject: [FT-60] FT-60 Possible Problem- suggestions?
? Encountering a problem in programming my FT-60. ?After entering a frequency (frequency+tone+tone freq.) ?and storing it in memory channel #2 (for example) any attempt to transmit on that channel results in FT-60 shutdown (power off to blank screen), and reboot to startup screen with audible beeps, 'MEMORY', ?battery voltage value and then contents of memory channel 2 showing on screen. ? I have tried a complete reset (F4 ALLRST). I have tried programming manually and via software. ? All receive functions are fine. I can receive ham bands, public safety, weather channels, etc. Battery functions are fine. ? This FT-60 has worked fine in the past, but has been out of service for a couple of years and simply stored carefully. ? Any suggestions as to the problem transmitting would be appreciated. Thanks. ? Hank? KB1JLA
|
Re: FT-60 Possible Problem- suggestions?
We are assuming that you are loading a freq within the ham bands, right?
toggle quoted message
Show quoted text
-------- Original message -------- From: "'hank' hanklane@... [FT-60]" <FT-60@...> Date: 12/07/2016 16:39 (GMT-07:00) To: FT-60@... Subject: [FT-60] FT-60 Possible Problem- suggestions?
?
Encountering a problem in programming my FT-60. ?After entering a frequency (frequency+tone+tone freq.) ?and storing it in memory channel #2 (for example) any attempt to transmit on that channel results in FT-60 shutdown (power off to blank screen), and reboot to startup screen with audible beeps, 'MEMORY', ?battery voltage value and then contents of memory channel 2 showing on screen. ? I have tried a complete reset (F4 ALLRST). I have tried programming manually and via software. ? All receive functions are fine. I can receive ham bands, public safety, weather channels, etc. Battery functions are fine. ? This FT-60 has worked fine in the past, but has been out of service for a couple of years and simply stored carefully. ? Any suggestions as to the problem transmitting would be appreciated. Thanks. ? Hank? KB1JLA
|
Programming Kit & Charger FS
I have the following FT-60R accessories for sale:
1 - RT Systems ADMS-1J Programming Software (with installation key) &
USB Cable all in the original box.
1 - VAC-370B Drop-in Rapid Charger & wall wart in original box. Charges
the FNB-83 in approximately 1.5 hours.
Please contact me off list at k5jg at verizon dot net if interested.
Thanks.
73, Jim K5JG
|
Re: FT-60 Possible Problem- suggestions?
Sounds like a bad battery or you are trying to transmit while charging. Plugged into a cigarette lighter plug will work, the wall wart won't.? Jardy Dawson WA7JRD Sent from the Death Star for Darth Vader's eyes only. Any other reception will be severely punished. ?
toggle quoted message
Show quoted text
On Jul 12, 2016, at 15:39, 'hank' hanklane@... [FT-60] < FT-60@...> wrote:
?
Encountering a problem in programming my FT-60. ?After entering a frequency (frequency+tone+tone freq.) ?and storing it in memory channel #2 (for example) any attempt to transmit on that channel results in FT-60 shutdown (power off to blank screen), and reboot to startup screen with audible beeps, 'MEMORY', ?battery voltage value and then contents of memory channel 2 showing on screen. ? I have tried a complete reset (F4 ALLRST). I have tried programming manually and via software. ? All receive functions are fine. I can receive ham bands, public safety, weather channels, etc. Battery functions are fine. ? This FT-60 has worked fine in the past, but has been out of service for a couple of years and simply stored carefully. ? Any suggestions as to the problem transmitting would be appreciated. Thanks. ? Hank? KB1JLA
|
FT-60 Possible Problem- suggestions?
Encountering a problem in programming my FT-60. ?After entering a frequency (frequency+tone+tone freq.) ?and storing it in memory channel #2 (for example) any attempt to transmit on that channel results in FT-60 shutdown (power off to blank screen), and reboot to startup screen with audible beeps, 'MEMORY', ?battery voltage value and then contents of memory channel 2 showing on screen. ? I have tried a complete reset (F4 ALLRST). I have tried programming manually and via software. ? All receive functions are fine. I can receive ham bands, public safety, weather channels, etc. Battery functions are fine. ? This FT-60 has worked fine in the past, but has been out of service for a couple of years and simply stored carefully. ? Any suggestions as to the problem transmitting would be appreciated. Thanks. ? Hank? KB1JLA
|
Re: Programming from FT-7800 to FT-60
Thanks for the replies and suggestions. I guess I'll have to go thru and try it again until it works. I thought I was but maybe I'm missing something.
Thanks again
Hoyt
?
|
Re: Keep FT-60 on Standby ?
I am sorry - I ?meant no disrespect .
>> ,,,?"It is not good for the battery to operate the radio, and be charging at the same time."
The only thing that having the FT-60 on while charging is that is will take longer for the battery to charge.?
And it has nevre been advised to TX while charging: If you do with a low battery, you might get out, but our chargers lack sufficient amperage to TX, plus they are not filtered, resulting in a nasty AC hum on your signal.
But leaving ON to monitor while charging cannot harm the radio,
Clint ?
|
Re: Programming from FT-7800 to FT-60
You have to export the FT-7800 data as tab delimited, then import it to the FT-60 programmer. The software should organize the file when imported. The reason for this is that the FT-60 has different features than the 7800 (hyper memories, etc.) and some things won't cross over without doing a proper export/import.
Jim, AD0AC
|
Re: Programming from FT-7800 to FT-60
I have a FT7900 and FT60, and the RT systems software for each. All I had to to was, literally, “copy and paste” from one into the other. Worked perfectly. Not sure why this is an issue, unless the FT7800 worked differently from the FT7900.
|
Re: Programming from FT-7800 to FT-60
?
Somehow I got to copy the data from the 7800 to a
new file for the 60. ?Anyway, when I try to send it to
the radio, I get the message that the data doesn't match
the radio (?) ?Both rigs use the version ?4 programs
from RT Systems, ?and I was under the impression it
would work. ?Any ideas as to where I am going wrong?
RT Systems needs to hear this question loud and clear. I have the
same combo of radios and RT Systems
software and hardware for both. I struggled with the same issue. I
had the good fortune to see them
at a Pacificon and they showed me how to do what you ask. It isn't
too complicated but also isn't
well explained or intuitive. I don't really remember all of the
steps.
My bottom line response is really - take this question to RT Systems
- they do respond to questions.
While chirp may work, it is just different and will introduce more
issues with data structure conversion
and "loss" in translating the data from one format to another.
73
Terry
Thanks
Hoyt ?n2jdk
Bokeelia Fl.
|
Re: Programming from FT-7800 to FT-60
Are you:
1.Saving the 7800 file in the software.
2. Connect the FT60 and download the radio template
3. Give that file a new name.
4. Import the 7800 data to this new file
5. Upload the file to the FT-60
?
Somehow I got to copy the data from the 7800 to a
new file for the 60. ?Anyway, when I try to send it to
the radio, I get the message that the data doesn't match
the radio (?) ?Both rigs use the version ?4 programs
from RT Systems, ?and I was under the impression it
would work. ?Any ideas as to where I am going wrong?
Thanks
Hoyt ?n2jdk
Bokeelia Fl.
--
KQ?J
|
Re: Programming from FT-7800 to FT-60
Try using CHIRP. Very easy to copy info from one radio to another.? Jardy Dawson WA7JRD Sent from the Death Star for Darth Vader's eyes only. Any other reception will be severely punished. ?
toggle quoted message
Show quoted text
On Jul 10, 2016, at 07:05, Hoyt7811@... [FT-60] < FT-60@...> wrote:
?
Somehow I got to copy the data from the 7800 to a new file for the 60. ?Anyway, when I try to send it to the radio, I get the message that the data doesn't match the radio (?) ?Both rigs use the version ?4 programs from RT Systems, ?and I was under the impression it would work. ?Any ideas as to where I am going wrong? Thanks Hoyt ?n2jdk Bokeelia Fl.
|
Re: Programming from FT-7800 to FT-60
The experts will correct me but I've found that the RT software likes to download from a particular 60 before it will recognize it for an upload.?
toggle quoted message
Show quoted text
On Jul 10, 2016, at 7:05 AM, Hoyt7811@... [FT-60] < FT-60@...> wrote:
?
Somehow I got to copy the data from the 7800 to a new file for the 60. ?Anyway, when I try to send it to the radio, I get the message that the data doesn't match the radio (?) ?Both rigs use the version ?4 programs from RT Systems, ?and I was under the impression it would work. ?Any ideas as to where I am going wrong? Thanks Hoyt ?n2jdk Bokeelia Fl.
|
Programming from FT-7800 to FT-60
Somehow I got to copy the data from the 7800 to a new file for the 60. ?Anyway, when I try to send it to the radio, I get the message that the data doesn't match the radio (?) ?Both rigs use the version ?4 programs from RT Systems, ?and I was under the impression it would work. ?Any ideas as to where I am going wrong? Thanks Hoyt ?n2jdk Bokeelia Fl.
|
Re: Keep FT-60 on Standby ?
Hey Clint
You took one snippet of my message and dissected it out of context.
The moral of the story is what I said after the quoted part: "It is not good for the battery to operate the radio, and be charging at the same time."
Now do you agree or disagree with this part of my reply? 73
Wassim WN6WJN
|
I had similar problems when I first tried to use FT-60 Commander. The solution was to go on the transfer menu and select the Alternate Write Method.
+++++
Jerry
KG7NOR
+++++
Live simple, love well, and take time to smell the flowers along the way. ~ Mark Twain
toggle quoted message
Show quoted text
?
I downloaded the FT-60 commander Software and I have the cable for the FT-60 radio but I get an error no matter what port I try using. I'm running windows 10 but I wouldn't think that would have any affect on it. Any suggestions or is their something I'm
missing?
|
If your cable shows to be a Prolific, roll your driver back to 3.2.0.0. You can find this at . Make sure you use the same USB port each time.? Jardy Dawson WA7JRD Sent from the Death Star for Darth Vader's eyes only. Any other reception will be severely punished. ?
toggle quoted message
Show quoted text
On Jun 29, 2016, at 16:41, eagle127@... [FT-60] < FT-60@...> wrote:
?
I downloaded the FT-60 commander Software and I have the cable for the FT-60 radio but I get an error no matter what port I try using. I'm running windows 10 but I wouldn't think that would have any affect on it. Any suggestions or is their something I'm missing?
|
I downloaded the FT-60 commander Software and I have the cable for the FT-60 radio but I get an error no matter what port I try using. I'm running windows 10 but I wouldn't think that would have any affect on it. Any suggestions or is their something I'm missing?
|
Hank-
Dave Jeffries AF0DJ