开云体育

Hello all. I am BRAND new to the FT101 so be patient with me. I'm new to radios of this vintage in general and just got this radio yesterday and haven't had time to play much with it but I'm pretty

Thanks for sharing the link Emerson.? An excellent article on not only what NOT to do by why not...? ?I am always on the lookout for another FT101Z but will now be wary of the 'not working'

Emerson, thanks for that. That cements my decision to return my 101E to original. At least I can backtrack what I did and it should work ... I've already bought the replacement 6JS6C sockets. Now I

http://lists.contesting.com/_yaesu/2003-06/msg00028.html A good advice.

Interesting. My 101Z suddenly became 'deaf' some time ago.? After a lot of investigion work I came to the conclusion that? the first RF Amp device had likely failed.? I am a little reluctant to

My 101zd was about 10db down on rx. I went down the troubleshooting road and cleaned all the relays I could find and checked the lamp fuse. Wound up changing the first rf amp and it came back to

Are there any members who have made the conversion from 6JS6C finals to 6883Bs according to the K3JLS.net documents?? If so, do you have any recommendations? I've done the conversion but have yet to

Thank you Don...appreciate it!Mike

On Wed, Jun 28, 2023 at 09:54 PM, mikemm58 wrote: > > So here is what I currently have onboard, mine is an E model serial > 240595, hope this helps > > BLANKER???? PB1582B > REG *PB11547B* >

I bet its the switch, try using the other side of the switch that is not used, boom... works KC6RHE Don

Keith,I would make sure the contacts on both relays are not corroded and making good connection. I assume you know how to do that?Does the 'VFO' red LED stay lit when you key?Mike

Thanks Mike, I checked pins 1&2 and they are shorted.? I did pull out the other relay and it looked good, i didn't pull it apart.? When i key up or put it into MOX mode it sounds like it's still in

Sorry about that I put my call sign in my profile and thought it would be visible on my posts.? KN6WNE Keith.? I do have schematics, I'll check what you've written.? It won't go into transmit with

Hello, Not sure who you are. No name or call sign at end of your message. Download a schematic and start tracing from pin 3 of the microphone connector past the MOX switch. (Does the radio TX

Also check the other relay in the audio section (not just the antenna relay)Make sure pins 1&2 on the accessory jack are shorted.That allows heater current to flow.Mike

You might also want to post your query on the Facebook group dedicated to the FT-101: Keeping The Yaesu FT-101 Alive! | Groups | Facebook <https://www.facebook.com/groups/759974814527577> They have

Hello all, I recently wanted to try my hand in getting an old rig. I bought an FT-101B on ebay, untested of course.? It does receive pretty good on the bands but it will not transmit.? The mic I

Ok I think I found the answer. My manual, in Section 6 "MODIFICATIONS", page 6-21 & 6-22 describes a fix for "Hum Problems", and calls for the addition of a 1000uf/25v electrolytic on T12 to ground

Perhaps some boards where swapped in the past. Hope the best for you. Fernando N2FQ/6 oh.. there is a facebook group if you’re so inclined. “Keeping the Yaesu FT-101 Alive"

Thanks Fernando. Yes I have that chart?My point is, My serial number (241468) doesn't seem to jive with the choices given on the chart for the EE.The chart gives:Early 15,000 and downMid.? ?15,001