Donald,

I haven't been able to find if the radio to find if the radio can be run on the charger without the battery in the manual. Of course, I could be missing it.

I have been to that link. I'm not sure if I want to order a battery and matching charger if the radio itself is dead.

Thanks for the reply and info.
--
Rick, KK4GGL

开云体育

Let's see the rig.

Rick . . .

(see below)

I have acquired an FT-80r.
The battery (FNB-41xh Ni_MH)is dead (measured with a multi-meter).

The charger that came with it is an NC-60B (for Ni-CD). The charger tested as putting out the specified voltage/amperage.

I have DLed the manual. the NC-60B is mentioned, as are Ni-CD batteries. Ni-MH aren't mentioned anywhere.

Anyone know if I should be able to power up the radio with the charger plugged in, but no battery.

Is it OK to charge Ni-MH batteries with the NC-60B Ni-CD charger?

Any ideas on how I might power up the radio without a battery?

Any and all help appreciated.

for what its worth,i have a yaesu ft-707 but i have always regarded yaesu being like chinese radios without the qc!,not a fan,seems they are built too much to a price point!.

I had a similar problem with the 710 that I got used.? It had a very early version of firmware (like 1.01 for everything).? The fix for your issue is to completely turn the radio off after the update has completed installing.? I got two messages that said something like 'select update file' and had to load the update two or three times.? I powered it off after each update had installed and now it's working great.? I hope this helps.? Dave N2EPV.

I recently picked up a DMU-2000 to go along with my FT-2000D.? When I connected it, I found that the 2023 CMOS battery was completely dead which cleared any BIOS settings in the DMU.? I replaced the 2023, was able to get the time to stay correct, but the DMU still will not boot.? It displays the two horizontal bars from the OS boot process, but instead of the main DMU screen appearing, it instead turns itself back off.? I believe that possibly one of the BIOS settings needs to be changed so that the boot process will complete, but can't figure out which.? The ham that sold it to me claims that it was in fact working when he sold it to me, but I'm not getting very far with that.

thanks in advance
Dave, N2EPV

I bought the product 1 month ago, I installed a software update on the device and when I turned it back on, the device said that I had to reinstall it, I reinstalled it, but it keeps me in the same loop as if it had never been installed, it gives an error 001 as soon as I open it, I update it every time, but again as if nothing happened. opens

Also check with the WIREMAN.com Also search Make and model of the Radio on GOOGLE or BING, you may find supplies for that specific Radio.
Again, GOOD LUCK

Hi Mike, I have the Yaesu part number but there is no info on it but I am sure it is a straight through pin out. Thanks Adam W4AJF

Adam, first check the Yaesu for a part number, then thick with I think it’s called CABLESAREUS.com

Good luck,Mike KM4FWT
P.S. I’ll do some more research, I might be wrong about the name of the place.

Hi all, new to the group. I have a Yaesu FIF-232C but it came without the 6 pin to 6 pin DIN cable so I will buy one, can anyone confirm that it is in fact pin to pin straight through wiring?

Thanks for any help.

Adam Farber W4AJF
Cooper City, FL

Hi all, new to the group. Can anyone tell me in the 6 pin Din to 6 pin Din cable for the Yaesu FIF-232C is pin to pin? I am looking to by a couple of them.

Thanks for any help.

Adam Farber W4AJF
Cooper City, FL

2 meter Transceiver, Power Supply,
Crystal filters, Manuals, and
more For Sale:

.

Yaesu FT-1900, 55 Watt 2 m transceiver:

The Yaesu FT-1900R provides toughness in a high
performance 55 watt 2-meter FM transceiver. The
receiver covers 136 to 174 MHz with illuminated
front panel keys and 200 memories. You get CTCSS
and DCS Encoder and Decoder circuits and keyboard
entry of frequencies directly from microphone.
5.6 x 1.6 x 5.8 inches.
The supplied MH-48A6J DTMF hand mic is backlit.
It comes with the MMB-36 mounting bracket and
DC cord. It requires 13.8 VDC at 11 Amps.

Features:
200 Memories (6 Character)
8 Memory Banks
55 Watts Output
Automatic Power-Off
Automatic Repeater Shift
DTMF Memories
CTCSS and DCS Encode/Decode
CW Trainer
Severe Weather Alert
Backlit DTMF Mic

This one works 100% and looks like new.
No scratches or defects.

Buy it with DTMF Mic, power cord, mobile bracket,
and paperwork for $100.

.

Yaesu FP-707, 20 Amp Speaker/Power Supply:

The Yaesu FP-707 is a 20 amp 13.8 Volt DC
Power Supply, with a very nice front facing
speaker in the same enclosure.

Cosmetically, it matches the FT-707, FT-747,
FT-757 and likely others.

Electrically, it can provide up to 20 amps,
so will work with most any HF and/or VHF rig.
It also has a set of binding posts on the back
for easy connection of a rig in addition
to the HF rig.

The speaker has a 3.5 mm plug on it.

This particular unit is in very good shape
both electrically and cosmetically. I can
not find a scratch, dent, or ding on it.
Electrically, it works as it should.

Buy this unit with manual for $125.

.

Astron RS-20 A, 20 amp Power Supply For Sale:

This power supply is useful for Amateur Ham Radio
applications, a test bench, or any place where
regulated 13 V DC is needed at fairly high current.

Astron power supplies feature solid-state electronic
regulation, EMI filter, fold back current limiting for
protection from excessive current and shorted output.
Input voltage is 115 VAC 50/60 Hz. Crowbar over
voltage protection is also provided. These high
quality power supplies are manufactured in the U.S.

The RS-20 A is rated at 20 amps intermittent use,
and 16 amps continuous duty. The output voltage
can be internally adjusted, as can the current
limiting.

This particular supply works great.
It only varies 0.01 Volts with a load!
Cosmetically it looks really great.
It does have a Yaesu label on it, which I will
leave in place.

With paper work for $70 plus shipping from Florida,
or pick up near Ocala, FL.

.

Yaesu Crystal Filters

These fit the FT-1000 series, among others, and are for the 455 KHz IF.

XF-455K-202-01
2000 Hz wide for SSB $85

XF-455K-501-01
500 Hz wide for CW $110

.

Yaesu NC-9 B Charger
13 V DC at 45 ma, 2.5 mm plug; $12

.

Original Yaesu Manuals:

These are the manuals only. All are originals, and not copies.
Most are in close to new condition.

FNB-9,10,11,12 Battery packs, $2
FC-757AT Antenna Tuner, $10
FT-100 HF/VHF Transceiver, $18
FT-470 Dual Band HT, $10
FT-757 GX, HF Transceiver, $18
FT-720 R, 2 meter mobile, $8
FT-1802 M, 2 meter mobile, $12
FT-2700 Dual Band Xcvr, $12
FTH-2005 HT, $5
FTS-8 tone squelch unit, $3
FTS-12 tone squelch unit, $3
MH-1B A2B speaker microphone, $2
SP-101 P, Speaker / Phone patch, $5
VX-1 dual band HT, $10

Maintenance Service Manual for Yaesu FT-208 R
2 meter HT. Looks new. $25

These are original Yaesu operating manuals only,
in very nice condition.

.

I also have many other accessories available such as many
different types of microphones, HTs, VHF and UHF rigs, HF
and VHF/UHF antennas, connectors, miscellaneous accessories,
etc.
Just too many to list here. Please e-mail your requests.

.
Prices do not include shipping from Florida.

Thanks.

73,

Ken, W8EK

Ken Simpson
E-mail to W8EK@... or W8EK@...
Voice Phone (352) 732-8400




.

Hi,
Has anybody got a FRG8800 Display unit For sale as mine has been damaged in transit and has Gone black because it got cracked.
Thanks for your time reading this post.
Regards:-Ian

I am trying to help another ham friend out.? He has a FT-4700H that won't cover all the US frequencies.? There is a post in the cloud for doing the modification, but it is unclear as to what you actually need to solder.? It says locate jumper 1,2,5,9,10,13 and short them with solder on the control unit.? Well there are no jumpers that are available to bridge.? The only thing I found was a IC that has 14 pins (Q5) on the board that you could short the pins too.? I have a bad feeling about this and wonder if anyone has addressed this on one of these boards?? They don't give enough detail about where this is on the board.? Waiting for more input on this subject.

Thanks

Richard Hopkins - W5TXK
rhopkins1951@...?

For advice....

Thanks

Dan,

You might also post thin in the larger Fox Tango group to have more eyeballs on
your question.


Donald KX8K



On Sat, 10 Jun 2023 08:12:07 -0700, "Daniel Velez" <Djvnet@...> wrote:

On the FTM500 when I'm in menu 84 setting the Beacon Status Tex and i select Text 1 and then "Freq & SQL & Shift" i am then presented a text input form that has 7 spaces, a colon, and more text input area. I have no idea what goes here and what the formatting is for.? I have searched high and low for this on the internet and in the manual and I just can't find an explanation of those strange spaces and the colon and additional spaces.
Can someone advise?
73 de Dan

----------------------------------------------------
Some ham radio groups you may be interested in:
/g/ICOM /g/Ham-Antennas
/g/HamRadioHelp /g/Baofeng
/g/CHIRP

On the FTM500 when I'm in menu 84 setting the Beacon Status Tex and i select Text 1 and then "Freq & SQL & Shift" i am then presented a text input form that has 7 spaces, a colon, and more text input area. I have no idea what goes here and what the formatting is for.? I have searched high and low for this on the internet and in the manual and I just can't find an explanation of those strange spaces and the colon and additional spaces.?
Can someone advise?
73 de Dan

See?. Jumper JP6 gets shorted out & the radio reset to transmit/receive 25?-75 MHz. As it comes from the factory they will only xmt in ham bands. There is interest in using 40.68 for tnx & receive using FT8.
A wire or tool across JP6 avoids the soldering.

73 de

Jack
W2INF