开云体育

Indeed, as the 7001 FW is a backport of the 7100. But the YD7001 lacks the measurement hardware. in a couple of weeks I will publish a hardware patch to the 7001 PCB that enables Voltage

This is the same for me. I was told yesterday in the Facebookgroup that this is "by design" for the YD7001. https://www.facebook.com/groups/yamorc.kunden/permalink/3490020587888649/ The new YD7100

Hmm, Timeout is set to 0. I jjust updates the YD9401 and it went from v1.1.3 to 1.1.1, so maybe that will fix my issue. -- Heath @ Human[c]ity http://www.humancity.org ( http://www.humancity.org/

I have been running much like Vinny but recently upgraded. I had disconnect problems until Karst told me to set the timeout setting for the LocoNet connection to zero. I think that is the change you

My DR5000 has been working with JMRI using the Ethernet connection for years. I only use the USB for configuration. I have not upgraded to Yamorc yet. I will look at the setup and follow with you.

I hope I am doing something wrong again..... I connected a 15v DC power supply (Meanwell 15P1J) to the YD7001. The 15v DC is confirmed by my multimeter. However in the YD7001 app (Build 59) the power

I spoke too soon. It only works for about 5 minutes and then stops working. As much as I would prefer to use the network connection between the YD7001 and JMRI, I am going to go back to USB for the

Oh fantastic, I do have the YD7001. -- Heath @ Human[c]ity http://www.humancity.org ( http://www.humancity.org/ ) http://www.riversidetransfer.nyc ( http://www.riversidetransfer.nyc/ )

I have both USB and the netowkr connected. But in the panel, I selected USB. From your comment, it sounds like maybe I need to unplug the network cable completely. -- Heath @

You obviously have not connected the YD7001 to USB.

Yes, that will work in the default-mode: Where you can set the start address at "First Contact" ( note !! 0-based !! ) Also that is possible: Of course this is only possible with the YD7001. The

Simplest way of doing so is: Find a LAN cable, plug it into your home-router / access-point.? That's it. It will work. That is, if you user WiThrottle - like products on the phones. Otherwise ( e.g.

It will simply take the next 16 addresses (assuming YD6016CS) after the YD6016LN-ES that its connected into. Sent: Monday, October 2, 2023 10:27 PM To: [email protected] Subject: YaMoRC,

Is there a way to set a specific address to an S88N device, or is the address completely based on where it falls in the data wiring path? For example, could I set the first one at 101 and the second

What is the latest firmware for the YD9401? I have 1.1.3 and I get an error if I try to update. -- Heath @ Human[c]ity http://www.humancity.org ( http://www.humancity.org/

Thanks Ryan!! -- Heath @ Human[c]ity http://www.humancity.org ( http://www.humancity.org/ ) http://www.riversidetransfer.nyc ( http://www.riversidetransfer.nyc/ )

I got it working. LB Server is port 5561, once I figured that out everything is now working. -- Heath @ Human[c]ity http://www.humancity.org ( http://www.humancity.org/

This is how my system is setup. just plugged the command station into my network and it’s available. Are you setting it up over WiFi or can you hardwire the command station. -- Heath @

Hey all! Could someone help me in integrating the DY7001 into my network? I would like to have people who come over be able to log into my home network, and the YD7001 be there on their phone apps. I

Vinny, I was never able to get the DR5000 to consistantly work over the network, so I was using the USB connection. Robert, thanks for this information. So I am assuming that you are not running the