Welcome to the YaMoRC/Digikeijs English Forum
?
This Table of contents provides information about the YaMoRC and Digikeijs products in US English and JMRI.
Click on the "Read More" to see all the information.
Legal notice:
All instructions are written to the best of our knowledge and belief of the respective authors.
Nevertheless, no liability for any errors or omission in the Documentation is intentional!
?
General:
The Main website of the manufacturers YaMoRC and Digikeijs can be reached via the following link:
- Link to the
- YaMoRC Support for Documents. TBD
- Link to the Digikeijs Firmware:?The latest firmware for each product will be in its respect file directory if we have the latest firmware.
- This is an archive that was made and will have documents in other languages. Check before you download.
?
US Dealers:
- for YaMoRC and Digikeijs Products.
Click on any RED Model number below, it will send you to the files page for that device.
English Only Manuals and Photos, etc can be found on this Forum and elsewhere:
Central Station:
- DR5000 The first Command Station with all conceivable connection sockets and LED status lights, USB, LAN & WLAN
- Detailed Tutorial - Rudy's Model Railway Videos on DR5000
Booster:
- DR5033 3 amp Booster works with many different Command Stations
Switch and Servo Modules:
- DK50018 16 Channel Bluetooth accessory and switching decoder
- DR4018 16 Channel Multi-Protocol Switching Decoder
- Manual: DR4018 Advanced V1.2
- Video Series for the DR4018 or DK50018 on Preset 1 in JMRI to invert the outputs for LED Signals.
-
- Guide for Testing the DR4018/DK50018 for proper Preset Configuration.?
- DR4024 4-output multi-protocol servo decoder with 4 additional switching outputs
?
Feedback Modules:
- ?DR4088CS & CS-GND 16-input feedback module (S88)
?
- ?DR4088LN-CS, LN-GND & LN-OPTO 16-input feedback module (LocoNet)
-
?
- ?DR4088RB-CS & RB-OPTO 16-input feedback module (R-Bus)
?
- ?DR5088RC 16-input feedback module with RailCom (LocoNet)
?
Reverse Loop Module
- ? DR5013
- Video :?
Turntable Module
- ??? DR5052
?
Other Equipment
- ??? DR4050 DigiLEDs RGB Model Train Light Control
?
- ??? DR5022 DigiControl for the control of 2 trains via a swivel
?
- ??? DR5039 LocoNet-B to CDE
?
- ??? DR5097 DigiNetHub 10x LocoNet Hub
?
- ??? DR5098 DigiNetHub 10x X-Bus Hub
?
- ??? DR5099 DigiNetHub 5x X-Bus Hub & 5x LocoNet Hub
Software
- JMRI
?
- RocRail
-
- ITrain
- Train Controller
- Perecli RRA (Railroad Automation)
- ?
- ?
- ?
- ?
- ?
-
- AnyRail:
Throttles:
- Document showing the Apps that work with JMRI and DR5000 with download links.
- Roco WLANmaus Throttle Setup For The Digikeijs DR5000
- Test of the Proto-Throttle with the Digikeijs DR5000
- RtDrive Lenz With The Digikeijs DR5000
- ESU Mobile Control II Throttle With The Digikeijs DR5000
- DigiTrainsPro (Android Phone) DR5000 Setup (Now a monthly fee of 5 Eros for this version)
- Z21 App for Apple or Android Phones.?
?
Other Features:
- ?
?
?
?
Re: DR-5013 set-up and Rocrail
Thanks so much Iain for your input
I modified my setting according to your suggestions with no success. Obviously you are correct it is indeed the CS that is detecting the short. My question is
By
botter
·
#3976
·
|
Re: DR-5013 set-up and Rocrail
I have a DR5013 used in the way you suggest (but with a Z21 and iTrain) and suffer none of the issues you describe. For the record and correctness it is not RocRail that is detecting the short
By
Iain Morrison
·
#3975
·
|
DR-5013 set-up and Rocrail
I'm using the DR5013 short detection capabilities to manage a "simple" reverse loop .? Following? the manual's instructions? I didn't modify any of the factory settings (no value assigned to S0-S3
By
botter
·
#3974
·
|
Re: Difficulty acquiring locomotives with a Duplex throttle
I just upgraded to the UR93 as the UR92 had difficulties acquiring locos with the YD7001. Actually the main problem wasn't acquiring locos as much as it was consisting them. Now that I have upgraded
By
Jim Tatum
·
#3973
·
Edited
|
Re: Unable to operate a flashing LED with DR4018
For info
2 x 220 micro farads worked, no buzz.
I still don’t understand why a standard LED works from the output of the DR 4018 but a flashing one doesn’t. Pity because it means lots of extra
By
RobinP
·
#3972
·
|
Re: Unable to operate a flashing LED with DR4018
Thanks Iain. I am using a separate power supply which I thought was stabilised but probably isn’t. I will experiment with a small capacitor and see if that works.
Robin
By
RobinP
·
#3971
·
|
Re: Unable to operate a flashing LED with DR4018
Robin
How are you powering the DR4018? If you are using DCC then you will have
rectified DCC as the output and what you are hearing is the ripple from
that rectified voltage.
A small capacitor
By
Iain Morrison
·
#3970
·
|
Re: Unable to operate a flashing LED with DR4018
I posted a question earlier regarding the DR4018 not being able to operate a tiny LED with built in flasher, it operates a normal LED with no problems. The recommendation was to use a small relay
By
RobinP
·
#3969
·
|
Re: Issues with DR5033s with upgraded DR5000 w/YD9401 module
Except for 1 thing.
Karst, the developer, emphatically states below that you should not be using common power supplies for HBridge components.
I know people have stated that it works and it obviously
By
Oldngrey
·
#3968
·
|
Re: Issues with DR5033s with upgraded DR5000 w/YD9401 module
Update!
While working with Thomas Ose of?OMS(re)models.com, who is very familiar with this system and a friend of mine. We have it resolved. I had to reverse wiring on the 4 5033s and configure the
By
Jim Tatum
·
#3967
·
|
Re: Issues with DR5033s with upgraded DR5000 w/YD9401 module
Jim,
Hover your mouse over the IB box. It says "The ID with which the YD7001 reports itself in Slot 0".
Sounds like I would never need to know it unless I was doing logging analysis.
By
Oldngrey
·
#3966
·
|
Re: DR5033 with Lenz DCC
Adam,
Thanks for the idea/solution.? I'm familiar Arduinos.? I use them to drive my servo controlled switch machines.? To finish it, Ryan fro Iron Planet Hobbies offered to reprogram the DR5033s
By
Mike L <mjlinden58@...>
·
#3965
·
|
Re: Issues with DR5033s with upgraded DR5000 w/YD9401 module
Thanks Oldngrey,
I found that one of the DR5033 was not set properly and matched it to the other 3 units. Looking at the Expert tab, I am wondering what this setting should be? IB or YD? And what
By
Jim Tatum
·
#3964
·
|
Re: DR5033 with Lenz DCC
I have a DR5000 with 2 DR5033 running 2 regions and the DR5000 running DCC accessories such as my DCC concepts Digital IP point motors - which I believe are pretty much like a tortoise but with a DCC
By
Adam Eddy
·
#3963
·
|
Re: Issues with DR5033s with upgraded DR5000 w/YD9401 module
Jim,
According to the DR5033 manual
I thougt common ground wiring referred to using a common track across all boosters not common power supplies.
You can configure the DR5033 from the YD7001. Just
By
Oldngrey
·
#3962
·
Edited
|
Re: DR5033 with Lenz DCC
Karst,
Thank you once again for the response. ?I understand that you do not like the auto reverse feature of the DR5033 however the Digikejis documentation says that the DR5033 has that feature.
By
Mike L <mjlinden58@...>
·
#3961
·
|
Re: Issues with DR5033s with upgraded DR5000 w/YD9401 module
I have a converted DR5000 with 4 DR5033 connected to a single regulated
power supply and this has shown no problems before or after the
conversion. I have all the DR5033 fuse protected but then that
By
tmose2012
·
#3960
·
|
Re: Issues with DR5033s with upgraded DR5000 w/YD9401 module
Thanks to all who responded and I greatly appreciate the feedback and recommendations. To be honest I researched the Digikeijs DR5000 and DR5033s, I did not find any information stating that it was
By
Jim Tatum
·
#3959
·
Edited
|
Re: Issues with DR5033s with upgraded DR5000 w/YD9401 module
For YaMoRC devices with HBridge it is not !! Every HBridge needs it's own double Isolated Switch-Mode powersupply. !!!
Not complying leads to Common Ground wiring, which is NOT supported and might
By
karst.drenth
·
#3958
·
|
Re: Purging locos YD7001
I could be wrong, but…
I thought that release would remove the locomotives from the slot they were occupying.
Whereas Dispatch would maintain the slot, allowing someone else to pickup the loco or
By
Heath @ Human[c]ity Junction
·
#3957
·
|