开云体育

When you hit the green button on the YD7001, and the booster LEDs show a short, does the YD7001 also show a short? Are you double gapped between the YD7001 and DR5033? FYI, I have this same

Are you 100% sure you do not have any of your track feeders swapped? Or that you don’t have any tools laying across the tracks or anything between the two rails that might be causing a short

Really!? ?That’s why all my digital IPs keep losing their addresses!

Can anyone tell me why this doesn't work? At switchon I get a short notification from the LEDs on the DR5033. The track is not getting any power. The DR5033 is visible from the YD7001.

Great, thanks again. -- Dave, Portland Church Hope Model Railway Facebook / Instagram ( https://www.instagram.com/church.hope.model.railway?igsh=YnV1bXVuMjVyZTQ0&utm_source=qr )

I would say yes, especially if you are using DCC Concepts IP digital turnout motors - helps to stop them losing their addresses Iain

Thank you Iain. As I have purchased 2 is it worth placing the 2nd one on the accessory bus? Dave -- Dave, Portland Church Hope Model Railway Facebook / Instagram (

You just place them anywhere – and one will be enough Iain Morrison <https://wimorrison.com> https://wimorrison.com Sent: 23 February 2024 09:16 To: [email protected] Subject: YaMoRC,

Hi I am using a Z21 to control my main track bus and a DR5000 for the accessory bus. I have an oval layout with the track and bus wired as a U shape, ie not a ring. I want to add track snubbers to

I am running version 8.2.5 -- Heath @ Human[c]ity http://www.humancity.org ( http://www.humancity.org/ ) http://www.riversidetransfer.nyc ( http://www.riversidetransfer.nyc/ )

s88n with loconet unplugged. With S88N unplugged and LN plugged in, it shows I have sensors from 1-345. The good news is when testing the sensors, they are showing up correctly, meaning what I

Did you disconnect the LN network and checked what the S88 network number was on the YD7001? -- Dennis Cherry Owner/Moderator

JMRI is also seeing 345 sensors instead of 160. -- Heath @ Human[c]ity http://www.humancity.org ( http://www.humancity.org/ ) http://www.riversidetransfer.nyc ( http://www.riversidetransfer.nyc/ )

I am not sure what is going on with my addressing, but it is showing sensors up to 345 when setting the loconet sensors to the address in my initial drawing. I am setting the address by pushing the

I tend not to share all the electronics I am using as people seem to think I am nuts with everything I am using on the layout. But I am having fun! -- Heath @ Human[c]ity http://www.humancity.org (

Yep, looked OK to me Iain Morrison <https://wimorrison.com> https://wimorrison.com Sent: 21 February 2024 18:20 To: [email protected] Subject: Re: YaMoRC, Digikeijs, JMRI, English Please

So will my addressing plan work? -- Heath @ Human[c]ity http://www.humancity.org ( http://www.humancity.org/ ) http://www.riversidetransfer.nyc ( http://www.riversidetransfer.nyc/ )

No issue using hubs, but as your picture was incomplete it made them appear superfluous. Iain Morrison <https://wimorrison.com/> wimorrison.com Sent: 21 February 2024 16:58 To:

The DR4088LN is to the left of the Command Station. 33-48 Everything else is to the right of the Command Station. 49-160 Using the first hub allows me to go in two directions. This also allows me to

Why are you using the Loconet hubs? You can simply plug into the DR4088LN Iain Morrison <https://wimorrison.com/> wimorrison.com Sent: 21 February 2024 15:06 To: