开云体育

I have a DR5000 with 2 DR5033 running 2 regions and the DR5000 running DCC accessories such as my DCC concepts Digital IP point motors - which I believe are pretty much like a tortoise but with a DCC

Jim, According to the DR5033 manual I thougt common ground wiring referred to using a common track across all boosters not common power supplies. You can configure the DR5033 from the YD7001. Just

Karst, Thank you once again for the response. ?I understand that you do not like the auto reverse feature of the DR5033 however the Digikejis documentation says that the DR5033 has that feature.

I have a converted DR5000 with 4 DR5033 connected to a single regulated power supply and this has shown no problems before or after the conversion. I have all the DR5033 fuse protected but then that

Thanks to all who responded and I greatly appreciate the feedback and recommendations. To be honest I researched the Digikeijs DR5000 and DR5033s, I did not find any information stating that it was

For YaMoRC devices with HBridge it is not !! Every HBridge needs it's own double Isolated Switch-Mode powersupply. !!! Not complying leads to Common Ground wiring, which is NOT supported and might

I could be wrong, but… I thought that release would remove the locomotives from the slot they were occupying. Whereas Dispatch would maintain the slot, allowing someone else to pickup the loco or

Jay, Thank you for the clarification. I use similar devices to you with WiThrottle, Engine Driver, WLANMaus but also the Z21 App on iPhone or Android. I have turned off the YD7001 Wifi and use a

After I updated to the YD7001 I accidently crossed the track A/B wires on the YD7001 to where they were no longer common with the DR5033's. Swapping the wires on the YD7001 cured the short circuit I

Moving back on topic in a moment: I am moving from a Digitrax system to the YaMoRC/Digikeijs world with a few DR5033's and a YD7001. I got them a few months ago when YaMoRC stock was briefly available

Brian I am going to take a shot at clarifying what Karst was saying about Release ..... In the WiThrottle protocol there are two commands that are supported - Release and Dispatch.? What they do is

Hi Brian, Well I actually meant thet releasing (purging) a refresh-slot is the responsibility of the controlling party. Not some kind of "garbage-collection" in the controll *ed* device, just because

Hi, Ah... you seem to be a bit impatient... Posting a ticket last night ;) Signing with your name is also considered polite around here. Your question: No you cannot. Our decoders do not have CV's

It think I know some one Vienna Austria that has a couple for sale. Richard

Jim, I will be following along as I am building a layout that has a YD7001 and a DR5033. Have you tried adjusting the speed at which the YD7001 triggers a short? It might just be reacting faster

Karst, Thanks for your response, I understand you may not implement the functionality. The Roco Z21 has implemented automatic release/purging of locos that have been stopped and are no longer

Where can you get a YD9401 in the US? Iron Planet is out of stock. Are they the only dealer? Thank, -bruce Bruce G Alcock | OK N-Rail | 405-381-4314<tel:405-381-4314> |

I have upgraded my DR5000 with the YD9401 module and followed all instructions as posted in this group and the the instruction found on the YaMorCo website. I have 2 issues at present. 1. The YD7001

Well Mike, As a "first" the DR5033 is NOT a reverse loop controller :O? That it worked in the first Loop, is based on pure luck... As a matter of fact, people using the DR5033 in this way, caused a

Hi Brian, Well, all you ask or expect to be present in the YD7001 is not there, and will not be there... Why ? Well, simple: Your WiFiTrax system is obviously not capable of handling a standard