开云体育

ctrl + shift + ? for shortcuts
© 2025 开云体育
  1. YaMoRC-Digikeijs
  2. Messages
Expanded Topics Messages Polls
Date
YD7001 stuck in demo mode etc.

 

After installing a YD 9401 into my DR5000? and dowloading the config software, I then installed it,? the activation message did not appear.
?
The config software was re installed again still no joy, it was also tried on an other desk top computer and laptop with the same issue both pc are windows 10 latest version.?
?
At one point I did see serial number but still not working it is just stuck in Demo mode with only the Track power leds on.
?
The DR5000/ YD7001 has a new power supply YD7460 3.3A 18V.
?
I would also like to use the Z21 WLAN MAUS if possible.?
Re: DR4024 Servo decoder installation file.

 

Thanks Iain. You've come to the rescue yet again! I'll add it to the files section in the next few days.?

Matt?
Re: DR4018 CV Settings for Signal lights

 

开云体育

I have 4 x DR4018 running 32 x 2 aspect signals with CV47=2. The signals show steady lamps and fade gracefully between the aspects when changed.

?

You may have set the brightness too low and are seeing flickering because of this.

?

From: [email protected] <[email protected]> On Behalf Of Rodney via groups.io
Sent: 16 December 2024 21:47
To: [email protected]
Subject: DR4018 CV Settings for Signal lights

?

Has anyone been able to get the DR4018 to issue a steady Signal light when CV47 is set to 2 ?
DR4018 CV Settings for Signal lights

Rodney
 

Has anyone been able to get the DR4018 to issue a steady Signal light when CV47 is set to 2 ?
Re: Can the DR60710 power supply cause damage to controllers it provides power to ?

 

It is nothing to do with having an earth in the outlet, although you should use such if using earthed equipment. In Europe (where outlets are earthed) anything which is exposed and powered like track has to fed from a supply that doesn't carry the earth through the power supply. Double insulation or class II is the easiest way to make sure that is true. I don't know what the rules are in Canada, I think in the USA you are free to take more risk.
?
Mike Ruby
Re: DR4024 Servo decoder installation file.

 

开云体育

?

Feel free to upload it ?

?

Iain Morrison

07767 456746

?

?

From: [email protected] <[email protected]> On Behalf Of Matt Wolstenholme via groups.io
Sent: 16 December 2024 13:54
To: [email protected]
Subject: DR4024 Servo decoder installation file.

?

Hi?

?

Please does anyone have a copy of the DR4024 servo decoder installation software and instruction manual they could upload? The file in the files section is empty.

?

Thanks (with fingers crossed!)

?

Matt?
DR4024 Servo decoder installation file.

 

Hi?
?
Please does anyone have a copy of the DR4024 servo decoder installation software and instruction manual they could upload? The file in the files section is empty.
?
Thanks (with fingers crossed!)
?
Matt?
YD7001 | Resetting Command Station after Short

 

Hello, (I have not read the manual, my apologies in advance.
?
Today during an operations session, there were many shorts, a good amount caused by operator error, but other from normal things. All the shorts were quickly cleared, but I then had to manually reset the YD7001. My layout is not that big, so originally I was not planning to install circuit breakers. But, I would also like a solution that will try to reset track power after a few seconds, only completely shutting down if the short is not cleared quickly.
?
Is it possible to set the YD7001 to retry track power after like 5 seconds, try 3 times, then require a manual restart after 15 seconds? Or some other similar scenerio?
Or do I need to get circuit breakers installed if I want this feature?
?
Thanks
--

Heath @ Human[c]ity
Re: Can the DR60710 power supply cause damage to controllers it provides power to ?

 

Karst,
??? our club is in Toronto Canada and we will be replacing all of our Digikeijs booster and command station power supplies. ? I assume that thee 3 prong version, GSM60A, is the better choice for us in North American because all of our AC outlets have a ground wire. ? ?
?
Is this correct??
?
Or are there technical reason we should go with the B version anyway.
?
Andris
Re: YD7001 questions - booster, consisting

 

Or try to look at other messages in this group....

/g/YaMoRC-Digikeijs/topic/109954783#msg4676
Re: YD7001 questions - booster, consisting

 

On Sat, Dec 14, 2024 at 02:58 PM, Bruce Alcock wrote:
Are there instructions on connecting JMRI to the YD001?
You could try JMRI's instructions for the DR5000
Re: YD7432 Reverser - recommended length of the Sensor track

 

Ok, great setup ??
Re: YD7001 questions - booster, consisting

 

No, the YD70xx need a minimum of 14DC.
?
that renders 12.8V to track out.
Re: YD7001 questions - booster, consisting

 

I think my last question is answered if I can use the GSM60A12 - that will give me 12 volt output.
Are there instructions on connecting JMRI to the YD001?
?
Re: YD7001 and decoder pro

Mario
 

Good evening.
What if it is a USB connection?
Thanks
Re: YD7001 and decoder pro

Mario
 

Buenas noches.
?Y si se trata de una conexión USB?
Gracias
Re: YD7432 Reverser - recommended length of the Sensor track

 

OK thanks Karst. My layout is also 00/H0 and the longest locomotive is about 28cm so with S1 and S2 planned at approx. 60cm each and the Track Out still having a length of over 4m I'm well within the specs.
All other track sections are supplied using YD6016 / DR4088 current sensors.
Re: YD7432 Reverser - recommended length of the Sensor track

 

I have it tested here with only 10cm length in H0. Also works, but that pre-requires your sections adjacent to S1 and S2 to also be suplied with a currecnt sensor.?
Re: YD7432 Reverser - recommended length of the Sensor track

 

longest Loco's length to be on the safe side.
Re: Can the DR60710 power supply cause damage to controllers it provides power to ?

 

Andris
?
The only additional comments that I will make on this topic is that Karst, in one of the previous posts, corrected his suggestion that we use the GSM60A supplies and instead stated that we should use the GSM60B supplies.? I cannot recall the reason for the change, but it should be somewhere in this topic.
?
Jay Lennox - Toronto
161 - 180 of 4744