¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. YaMoRC-Digikeijs
  2. Messages
Expanded Topics Messages Polls
Date
Re: YD7001 Power Supply Voltage

 

Indeed, as the 7001 FW is a backport of the 7100. But the YD7001 lacks the measurement hardware.

in a couple of weeks I will publish a hardware patch to the 7001 PCB that enables Voltage measurements.
Re: YD7001 Power Supply Voltage

 

This is the same for me. I was told yesterday in the Facebookgroup that this is "by design" for the YD7001.


The new YD7100 will show the correct voltage.
Re: YD9401 to JMRI

 

Hmm, Timeout is set to 0.

I jjust updates the YD9401 and it went from v1.1.3 to 1.1.1, so maybe that will fix my issue.
--

Heath @ Human[c]ity
Re: YD9401 to JMRI

 

I have been running much like Vinny but recently upgraded. I had disconnect problems until Karst told me to set the timeout setting for the LocoNet connection to zero. I think that is the change you need to make. Search the channel for that advice.
Vinny, let me know if you need help, I'm just up the road from you in Cary.

Regards,
Bob Gamble


On Wed, Oct 4, 2023 at 8:03?AM Vinny DeRobertis <vinny.derobertis@...> wrote:
My DR5000 has been working with JMRI using the Ethernet connection for years. I only use the USB for configuration. I have not upgraded to Yamorc yet. I will look at the setup and follow with you.


--

- Bob
Re: YD9401 to JMRI

 

My DR5000 has been working with JMRI using the Ethernet connection for years. I only use the USB for configuration. I have not upgraded to Yamorc yet. I will look at the setup and follow with you.
YD7001 Power Supply Voltage

 

I hope I am doing something wrong again.....
I connected a 15v DC power supply (Meanwell 15P1J) to the YD7001. The 15v DC is confirmed by my multimeter.

However in the YD7001 app (Build 59) the power supply window shows 19.0v and the track voltage window shows 17.8v.
My RRampMeter from DCC Specialties shows 14.1 volts on the track which is roughly what I expected.

I do recall buying a DR5000 with a 19v power supply initially since that was all there was available, but bought a 15v power supply rather than the supplied one as I run HO and not O scale. Is that a clue?
Re: YD9401 to JMRI

 

I spoke too soon. It only works for about 5 minutes and then stops working.

As much as I would prefer to use the network connection between the YD7001 and JMRI, I am going to go back to USB for the reliability.
--

Heath @ Human[c]ity
Re: Addressing S88N devices

 

Oh fantastic, I do have the YD7001.
--

Heath @ Human[c]ity
Re: Tip: Updating software / Firmware on YD7001

 

I have both USB and the netowkr connected. But in the panel, I selected USB.

From your comment, it sounds like maybe I need to unplug the network cable completely.
--

Heath @ Human[c]ity
Re: Tip: Updating software / Firmware on YD7001

 

You obviously have not connected the YD7001 to USB.
Re: Addressing S88N devices

 

It will simply take the next 16 addresses (assuming YD6016CS) after the YD6016LN-ES that its connected into.

Yes, that will work in the default-mode:

?



Where you can set the start address at "First Contact" ( note !! 0-based !! )

?

On Mon, Oct 2, 2023 at 02:26 PM, Human[c]ity Junction wrote:

For example, could I set the first one at 101 and the second one at 201 and the third one at 301.

Also that is possible:

?

Of course this is only possible with the YD7001. The DR5000 does not have this feature... ;)?

?

Greets,

Karst

?

P.S. Also YD6016LN has this option :)?
Re: Integrating YD7001 into my home network

 

On Mon, Oct 2, 2023 at 12:42 PM, Alex Nadeau wrote:
I would like to have people who come over be able to log into my home network, and the YD7001 be there on their phone apps.

Simplest way of doing so is: Find a LAN cable, plug it into your home-router / access-point.? That's it. It will work. That is, if you user WiThrottle - like products on the phones.

Otherwise ( e.g. Z21, App WLANmaus etc ) it might be wise to set the YD's IP-address to static, or ( maybe better ) set your DHCP server (router / access-point) to hand out a fixed IP to the YD.

?

When that all works, you might want to turn-off the YD's WiFi to free up a considerable amount of resources in the YD.

Greets,

Karst
Re: Addressing S88N devices

 

¿ªÔÆÌåÓý

It will simply take the next 16 addresses (assuming YD6016CS) after the YD6016LN-ES that its connected into.

?

From: [email protected] <[email protected]> On Behalf Of Human[c]ity Junction
Sent: Monday, October 2, 2023 10:27 PM
To: [email protected]
Subject: YaMoRC, Digikeijs, JMRI, English Addressing S88N devices

?

Is there a way to set a specific address to an S88N device, or is the address completely based on where it falls in the data wiring path?

For example, could I set the first one at 101 and the second one at 201 and the third one at 301.

Or do they need to be consequtive?

What if I added a LN module in front of the string of S88N modules?

Thanks
--

Heath @ Human[c]ity
Addressing S88N devices

 

Is there a way to set a specific address to an S88N device, or is the address completely based on where it falls in the data wiring path?

For example, could I set the first one at 101 and the second one at 201 and the third one at 301.

Or do they need to be consequtive?

What if I added a LN module in front of the string of S88N modules?

Thanks
--

Heath @ Human[c]ity
Re: Tip: Updating software / Firmware on YD7001

 

What is the latest firmware for the YD9401? I have 1.1.3 and I get an error if I try to update.


--

Heath @ Human[c]ity
Re: Replacement enclosures

 

Thanks Ryan!!
--

Heath @ Human[c]ity
Re: YD9401 to JMRI

 

I got it working.?


LB Server is port 5561, once I figured that out everything is now working.?
--

Heath @ Human[c]ity
Re: Integrating YD7001 into my home network

 

This is how my system is setup.??just plugged the command station into my network and it¡¯s available.?


Are you setting it up over WiFi or can you hardwire the command station.?
--

Heath @ Human[c]ity
Integrating YD7001 into my home network

 

Hey all!

Could someone help me in integrating the DY7001 into my network? I would like to have people who come over be able to log into my home network, and the YD7001 be there on their phone apps. I DO NOT want a separate SSID/Network. IF that is possible.

Thanks!
Re: YD9401 to JMRI

 

Vinny, I was never able to get the DR5000 to consistantly work over the network, so I was using the USB connection.

Robert, thanks for this information. So I am assuming that you are not running the LocoNet Server on JMRI, and the YD is the LocoNet server for the system. I will give this a try later.

Thanks
--

Heath @ Human[c]ity
1021 - 1040 of 4747