¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. YaMoRC-Digikeijs
  2. Messages
Expanded Topics Messages Polls
Date
Re: Want to buy: DR4088CS or LC-CS for new layout

 

Yes, I understand if I buy new that I could get the YaMoRC version.

I am trying to save a little money and buy used where possible.

Thanks
--

Heath @ Human[c]ity
Re: Want to buy: DR4088CS or LC-CS for new layout

 

You need to purchase the YAMORC equivalent
?

On Thu, 17 Aug 2023 at 01:59, Human[c]ity Junction <heath@...> wrote:
Hello,

I am working ont he wiring for my new layout and I just realized I am short a DR4088CS. Does anyone have one that they are no longer using that they would be willing to part with?

I am building a few of these for my layout. Block Detection with Relays to turn on/off power to each block.


Please email me directly if you have a DR4088CS or LN-CS that you would be willing to sell.

Thanks
--

Heath @ Human[c]ity

Attachments:

--

Many Thanks

Iain Morrison
Want to buy: DR4088CS or LC-CS for new layout

 

Hello,

I am working ont he wiring for my new layout and I just realized I am short a DR4088CS. Does anyone have one that they are no longer using that they would be willing to part with?

I am building a few of these for my layout. Block Detection with Relays to turn on/off power to each block.


Please email me directly if you have a DR4088CS or LN-CS that you would be willing to sell.

Thanks
--

Heath @ Human[c]ity
Re: YD9401 Upgrade Tip

 

Thanks John.? I have download the YD7001 manual. I will be very helpful when we start our conversion of the DR5000 with the YD9401 upgrade on Friday at the club.? Hopefully upgrade will arrive today or tomorrow in the post.

Jay Lennox, Toronto
Re: YD9401 Upgrade Tip

 

¿ªÔÆÌåÓý

I believe you can get the manuals here
Hope that¡¯s helpful

JC


XR

On 15 Aug 2023, at 23:11, Jay Lennox <jay.lennox@...> wrote:

?Hi

The YD9401 upgrade modules from Iron Planet Hobbies will be delivered tomorrow.? We plan to convert the first of our two DR5000s on Friday.? I have already requested a key so we will be ready to go.? Thanks to various posts here, and YouTube videos, upgrade process should be straight forward.

One question.? Documentation for the YD7001.? I checked the YaMoRC website and cannot find a manual - probably not looking in the right place on the site.? Does anyone know if a manual exists, or other material we can use to review the settings in our new command station?

Thanks.

Re: YD9401 Upgrade Tip

 

Hi

The YD9401 upgrade modules from Iron Planet Hobbies will be delivered tomorrow.? We plan to convert the first of our two DR5000s on Friday.? I have already requested a key so we will be ready to go.? Thanks to various posts here, and YouTube videos, upgrade process should be straight forward.

One question.? Documentation for the YD7001.? I checked the YaMoRC website and cannot find a manual - probably not looking in the right place on the site.? Does anyone know if a manual exists, or other material we can use to review the settings in our new command station?

Thanks.

Re: Zoom Room Today

 

Sorry I missed it. Notification was too late to organise myself for 4am (6pm GMT) in Australia. I read the message that came in overnight 2 hours after it had started. The joy of Timezone shifts ?

Re: Zoom Room Today

Les Waters
 

Dennis

Thank you very much for providing this facility. ?I am based in the UK.

I have successfully upgraded my DR5000 to a YD7001. ?But I know I will need help in moving forward. ?For some years I have been using TC Gold Version 9 with an ECoS 50200. ?I will not be upgrading to TC version 10. ?So, I am thinking of using iTrain/YD7701 in future. ?I am no expert in using the various DCC protocols so I will find this ¡°whereby¡± facility most useful if there are seminars/discussions on this type of setup.

Thanks again.

Les

Re: YD9401 Upgrade Tip

 

Glad you got it working again.
--
Dennis Cherry
Owner/Moderator

Re: YD9401 Upgrade Tip

 

After several times yesterday inputting the IP address into WLANMaus I tried again tonight and the flashing stopped and I am able to control a locomotive (Broadway Limited PRR P5a) with the WLANMaus.

Charles Long

Re: Zoom Room Today

 

Thanks:

I am back on again today doing testing.

Just missed Charles looking, was at lunch.
--
Dennis Cherry
Owner/Moderator

Re: Zoom Room Today

 

Dennis, Wereby was a helpful episode yesterday.
Thank you;
Jerry F

Re: JMRI YD7001 network communication not working

 

I wanted to wait a day or two to answer, but so far so good. I had one disconnect after the change but wanted to do a cold start just to ensure it wasn't some residual stuff. I did have it stay connected for several hours without any problem.

Regards,
Bob Gamble


On Mon, Aug 14, 2023 at 12:38?PM karst.drenth <karst.drenth@...> wrote:
On the Expert tab you need to set the LocoNet LBServer timeout to zero

did this also solve your disconnects Bob ??


--

- Bob

Re: JMRI YD7001 network communication not working

 

On the Expert tab you need to set the LocoNet LBServer timeout to zero

did this also solve your disconnects Bob ??

Re: Servo Controller Alternatives

 

Hi all,

Another company well worth checking out is the Swedish company MGP?

They have a very nice 'Servo5' servo controller board, very well priced and Loconet compatible. Programmable via a bluetooth module and an Android phone app, deals with frog polarity also with on-board relays.

MGP produce a range of Loconet compatible (and properly licensed) products, which is great for use with either a DR5000 or the future YAMORC command station. We've been using them for a few years now at our N Scale club here in Sydney Australia.

Thanks!

Jarryd

Re: Zoom Room Today

 

Would have showed up from France, except I didn¡¯t see the notice until to late.?

Much appreciated your giving the times in CDT and GMT. I know that I¡¯m at GMT+2 not sure what I am at with respect to the other.?

Bon soir

Richard Trilling?
On 13 Aug 2023 at 23:58 +0200, Dennis Cherry <dbcherry@...>, wrote:

We had 4 members show up today, 3 from the US and 1 UK member

The conversion was good as each one had a different problem, however we did not have enough time as the time limit was 40 minutes to fix any problems.

I have now taken the step and have 1 year of unlimited time on the Whereby YaMoRC room.

It is open 24 hours a day to all, as the 4 members said yes to using the Whereby Room.

I hope the Room is used to help our members out 1 to 1 on a problem and the other Room members watching learn at the same time or help out also.

I am looking forward to have Presenters to talk about certain topics in the near future. These will be scheduled in advanced and also will be recorded and put out on YouTube.

--
Dennis Cherry
Owner/Moderator

Re: Zoom Room Today

 

We had 4 members show up today, 3 from the US and 1 UK member

The conversion was good as each one had a different problem, however we did not have enough time as the time limit was 40 minutes to fix any problems.

I have now taken the step and have 1 year of unlimited time on the Whereby YaMoRC room.

It is open 24 hours a day to all, as the 4 members said yes to using the Whereby Room.

I hope the Room is used to help our members out 1 to 1 on a problem and the other Room members watching learn at the same time or help out also.

I am looking forward to have Presenters to talk about certain topics in the near future. These will be scheduled in advanced and also will be recorded and put out on YouTube.

--
Dennis Cherry
Owner/Moderator

Re: Servo Controller Alternatives

 

Hi, not sure about in the US but here in the UK MegaPoints respond very quickly to emails and are always helpful. The responses come from info@....?


--
Dave, Portland

Re: JMRI YD7001 network communication not working

 

FYI. Configured the system as described by Bob Gamble below. Worked like a charm.
Thanks again.
-Chris

Re: JMRI YD7001 network communication not working

 

Thanks Bob,

Very helpful. Will reconfigure later today.?
I am hardcoding the address until I get things working, then I will use mDNS.

-Chris

1241 - 1260 of 4750