开云体育

Problem: When using Vara FM the radio operates correctly, allowing sending and receiving of messages. When Vara HF is used the radio will not ‘key’, preventing transmission. Software: Winlink

Problem: When using Vara FM the Yaesu FT-100D operates correctly, allowing sending and receiving of messages. When Vara HF is used the radio will not ‘key’, preventing transmission. Hardware: ASUS

Thanks, Rick for the link to the paper. That's a keeper, for sure. Since I've only recently started working with Winlink, I was curious about some of the other modes, such as ARDOP and WINMOR. Winlink

VARA Shakeout Earthquake exercise on Oct 19 International Winlink Event * USGS is holding a big, international earthquake exercise on October 19.? Winlink will be transmitting some of the reports to

Greetings, I am new in using the subject programs.? I have registered VARA with Jose. My computer is a Win 10 Enterprise system. I have a number of questions, so here goes in no special order. 1. I

George, I have a Yaesu FT-710 that presents COM6 and COM7 on my computer. In the Winlink VARA HF session set up, I use Yaesu 991/A for the radio selection, COM6 for the radio control port and on the

It is for new machines, but when you get to using older machines for low demand tasks - such as, perhaps, digital radio ops, I've found that older macs, pound for pound, tend to remain workable, and

Dave, Sounds like you are on the right track.? I think you will see good performance and reliability on the path your on. ?I have been involved in Winlink since 1986 and written several HF protocols

Rick, Actually, I've been accumulating all the stuff I need to set up exactly what you describe. I'm located in Ann Arbor, MI and am planning to put up a packet/Vara FM node on 2 meters here. I have

For an alternative (I realize it may be heresy to even say "Windows" to a Mac group!!!) you can read about a low-cost alternative that several are using on VARA and VARA FM.? The available $100-200?

Thanks for your help, PatMc. I hope to be able to get to it later this week.73George KE8TSL

Hey George, I’m running an FT-991a to a W10 mini-PC and it does sound like a driver problem. You need to install the driver with the computer disconnected. Disconnect your radio, uninstall the

And, unfortunately, you have to be prepared to invest quite a lot simply to be in a position to start developing for the Mac... Reasonable specification hardware is more expensive than comparable

Thanks, Matt for your clear directions on how to access the Device Manager to see what was there. I found two items there: one for Com Port 3 and one for Com Port 4. I deleted the Com Port 4 item (I

HI Pat,I have a Yaesu FTdx10 connected to a laptop running Windows 10. I downloaded the CP210x Com Port driver from the Yaesu website but it may not have activated properly. I am trying to figure out

Just to be clear, many of those "other" sound card rig-interface devices perform PTT activation through an I/O pin on the (C-Media) USB sound IC, instead of through a "serial line" (COM-port) signal.

1)?? The only common vox-activated soundcard interfaces are the SignaLink USB, one of the RigExpert models,? and my home-brew tone-activated sound card at <http://WA8LMF.net/tonekeyer.htm> . . All

George, How are you connected to your radio?? Internal sound card or external (e.g., SignaLink or DRA). External sound cards typically use VOX for keying; no serial port required.? With internal

George, There was no attachment. Your email client does not support secure email signatures. I removed it for this reply. Try: Step 1: Open the Device Manager. Step 2: From the menu bar, click View.

Thank you, Matthew for these 7 downloads. But, before I open them, can you give me some details on what each is for? I certainly do not want to download any malware by mistake.Thanks,George KE8TSL