开云体育

Mine connected to Radiomail by selecting the VR-N76 in Radiomail itself. Same with aprs.fi. It doesn't seem to connect via the BT page in settings for those, but I have tried with multiple iPhones and

Hello Mark, Yes, I tried autotune and ping - no response. The last time something like this happened, I found it was because I was selecting VARA FM Radio only. Once I selected VARA FM Winlink,

Have you tried running an "Auto Tune", from the VARA FM "Settings -> SoundCard..." window? On your 'monitor' radio, you should hear all 10 signal bursts at increasing audio levels. Many radios stop

Has anybody gotten their hybrid RMS gateway successfully configured? I’m running relay, packet and trimode but I don’t want to tie up my 705. I’m using a g90 and ft-2980, is it possible to put

FWIW, I have tried a range of TX drive levels, but still no joy. Since the hardware works with my packet setup, I have to think it is something in RMS Express or the VARA-FM setup, but I changed

I had finally figured out how to use Winlink with VARA-FM and an AIOC into both a Baofeng and an Anytone 878. I also use the same hardware configuration for Direwolf/Outpost packet BBS operation.

Got it running. In Windows 11 there ?is a legacy program for sound under More sound settings and under the mic Custom tab there is a AGC box I had to click off that got turned on from a Microsoft

There are two radio shacks at my home. Mine upstairs connects to the east side antennas. My spouse’s shack connects to west side antennas. My Yaesu 857 connects to HF and Fm Winlink with no problem

After a freakish warmup here in central Michigan to 50 F / 10C for the last two days (it was -2 F / -19 C Sunday night), the snow and ice melted allowing me to get outside and do some antenna work. I

Hello, Facundo, I use an IC-7300 for HF Winlink. The Icom driver software puts two com ports on the computer. Only one works with RMS Express email. For the 2m Winlink gateway I am using a Rigblaster

Brian, Can't imagine what could cause this. Which DRA (and if it is a VOX capable, is it jumpered for VOX?)? Anyway, this is a Vara group, so I don't really want to continue down this path here.

Make sure your TX level is not set too high. Most Icom rigs will not go into TX if the audio drive is too high. -Scott, NS7C

Except there is no COM port in his configuration. The RIM 9600 uses the HID GPIO line for PTT. HIDs are sharable across multiple applications without conflict.

There are 2 versions...9600 and 1200 baud.? Which one do you have?? Settings will have to match. -- Roy Dugger, KD6R

I would assume this cable would work. I am using it with a FTM-6000. https://digirig.net/product/yaesu-ftm-cable/ Tyler Griffiths N7UWX See where I am:https://aprs.fiN7UWX-5

Lawrence - did you ever get this resolved? I'm having the symptoms.? I'm using Yaesu's CT-164 10pin to 6pin cable connected to the digirig 6 pin (male) 1200 baud to TRRS audio.? I've also used the

George, this is a very timely post as I was trying to do exactly the same yesterday. I followed the recipe that Steve K3FZT posted, but I am having issues with the PTT. I am using an IC-9700 as the

It's trivial UNTIL you want to run two or more sound card apps on the same sound device at the same time (such as both AX. 25 packet with the UZ7HO Soundmodem -AND- VARA ).? Then all hell breaks

I am relatively new to this. I use VARA HF with an Icom IC-7300 and VARA FM with Alinco DR-135 and Repeater Builder 9600 interface. Both use PTT, just by checking the box for RA-board in VARA setup.

VOX (as in a SignaLink or the "DATA VOX" function on some Yaesu radios) has huge advantages.? You avoid the hassle of serial ports, especially on modern computers that force you to use a