开云体育

Hello Eric, I don't understand why after executing Vara Install you would effectively make it unoperable by unregistering the needed OCX'es.... Pse explain. -- Cheers, Jan PH3J.

Could you be using the default data mode connector settings? (page 12-12 of the full 7300 manual, https://www.icomjapan.com/support/manual/2271) SET>CONNECTORS>DATA OFF MOD SET>CONNECTORS>DATA MOD The

My Kenwood TS890 does that too 73, Frank N3FLL

Like many on this forum, I also use Vara/VarAC with an IC-7300, I have no problems at all using it and the mode remains at USB-D. I am QRV by remote at the moment using Win4Icomsuite with VarAC. 73

Hi, I know this is a two year old thread, but I wanted to post a solution that I stumbled upon: The easiest way around this would be to run the "VARA Install.exe" again from a new VARA installation.

This is good advice, you need to look at the application(s) that are controlling the rig for the cause. Vara HF has no ability to change rig settings. -Scott, NS7C

I'm using an IC-7300 and VARA 4.8.7, and I haven't had that problem. In the WInlink Vara HF Session window, choose Settings, Radio Setup. There is a checkbox to Use Internal Soundcard. Be sure that is

Windows XP, 7, 8, 10, and 11 have all evolved device mangment including sound. They're competing with Apple, who designs and builds both the computer hardware and the operating system as closed black

Mine does the same. KM5VC ________________________________ Sent: Monday, June 3, 2024 6:19:23 AM To: [email protected] <[email protected]> Subject: [VARA-MODEM] VARA HF resetting Data mod on

Hi all, I've consistently been having an issue with VARA HF resetting my radio's (IC-7100) Data mod to ACC no matter how may times I set it to USB. I'm running Win 10 and VARA HF 4.8.7. A fellow club

Hi John, I would think your Signllink and Radio are fine. What is suspect is the computer. Try to switch computer as your variable and see what you find. Borrow a laptop from someone and give it a

John; Assuming you have a genuine Tigertronics (SignaLink) "SLCAB6PM" cable, the jumpers inside the SignaLink should be configured like so (this is how the "SLMOD6PM" module is wired): Note that

Mark, I am using the data cable that came with the SIgnalink.? It has the round 6-pin connector on one end (for the DATA connector on the radio) and the RJ-45 connector on the other end. I called

Jim, Initially, the values for Menu #s 46 and 47 were set at 4.? I moved them to 9 in hopes of getting some audio out to the Signalink, but no luck there, either. 73, John N5VCM

John; Since you don't (currently) have CAT rig-control set up, it appears that you're using the 'VOX' circuitry in the SignaLink to key the radio, and you're feeding transmit audio from the SignaLink

Jim, I am using the six pin connector that plugs into the DATA connector on the TS-480 main body. 74, John N5CM

John, Also check Menu #46 and 47 for your AF output and input levels, they might be set at 0, I have mine set at 3.

John, I have been running Winlink with VARA on my TS480HX for years now without any issues. I also use VarAC and other digital programs with it. I don't have a SignaLink but use a DRA-100 as my

The ARCP-480 software has NOTHING to do with using digimodes on the '480.? It's a virtual front panel that duplicates what you already have on the front of the radio.?? It's really intended for

Nothing yet, Ken, but I haven't given up. I have ordered cables to enable rig control on my TS-480 through a USB port on my computer.? I have downloaded the ARCP-480 software from Kenwood.? My cable