开云体育

Dear Roger, We are a hamradio group inside PA. We run a RDF project and like to ask if it is possible for you to give support to our DF dataformat. UIVIEW will display the DF bearings on the map. We

In article <3878835F.C7B7922A@...>, Ev Tupis (W2EV) <propnet@...> writes That's the correct version. The problem of DDE not working can occur when you get the DLL from the wrong

In article <000001bf5a9b$8004eb60$0201a8c0@...>, UI-View <ui- view@...> writes Set "MCOM ON" on the TNC you are using with UI-View/WinPack. UI-View works differently to most

Jim, this may not have displayed because it is an invalid plot. ......................................~ ........................................~~ The "1" after the "W" represents a "good plot", but

Please excuse the ignorance, is there a FAQ about APRS and/or UI-View ? I've been subscribed to the list for a while now and have a few hundred questions I don't want to clog things up with ! TIA ---

Hi Maurice The output is in miles not Km I could change it to be either if so wished Could you send me a log file of some local traffic and I will investigate the problem for you. see UI- Does that

Hi, I use UI-view 2.16beta with AGWPE 2000 (latest version) I'm also running UI-path 1.6 and have the following problems: The distance to the other stations is not correct |ON4BAM|0,0|Heard

Hi Jim, In almost every case, such problems have been solved by performing either: RESTORE D (which restores your TNC to factory default settings...including the need to re-enter your MYCALL) -or-

Roger Barker wrote: Hi Roger, Nice catch! I may very well have an "incompatible" version of the .DLL. I installed from the Windows98 SR2 CD-ROM. Doing a search for DDEML.DLL, I find it in the

In the not too distant future I think the D7+GPS+single port laptop system will work fine, it just needs a little work for the next beta. Of course, this doesn't get over the original problem if you

A fudge - is to have the GPS connected to a TNC (MYCALL-7) and low power txrx running into a helical ant (or even dummy load). This TNC in GPS mode beacons your location. This part of the package

Hi All, Although I am a beginner to UI-View/APRS, I'm definitely not new to Packet! I have a Kantronics KPC-9612 and have set it up to beacon GPS information, however the packets it sends are not

In article <000d01bf5a8d$9c0009c0$23212121@down>, Andy Pritchard <apritch@...> writes To try and avoid a possible red herring - Could there be some confusion here between UI-Path and UI-MH?

In article <000801bf5a87$dd3cd720$a6e2abc3@default>, Mike.G1ZRN <mike.g1zrn@...> writes BPQ32 is for use with 32 bit programs. You can't use it with either UI-View or WinPack, because they

In article <PBDgukAr78d4EwR5@...>, Roger Barker <roger@...> writes [snip] And someone is now probably going to tell me that WinAPRS does it! ;-) So, I expect the real answer is

Hi Ev The ini file has no significance as for as im concerned. The file was a solution G6HIB found to make it work on his system. UI-Path should and does! work without a ini file if run from the

Hi, A bit off topic and I haven't had chance really to look back and see if this has been asked already.... Has anyone got a WORKING URL for BPQ32/BPQ4.09/BPQ4.09a please? Or maybe you could email it

Ok, Andy... You just *had* to post this information, didn't you? :o) I was about to scrap UI-View and UI-Path because I couldn't get it to work on my computer, and then you go and post some screen

Hi, For those using host software under UI-View, BPQ 32 bit software is available from the following site http://www.btinternet.com/~wyreforest.repeatergroup/wfrg.htm on the "Software page" I haven't

In article <001201bf5a66$a7783420$ca21883e@g7mvo2>, Mark Armfield G7MVO <mark@...> writes There probably isn't a problem. The chance of a ping getting through and the ack getting