开云体育

In article <3878835F.C7B7922A@...>, Ev Tupis (W2EV) <propnet@...> writes That's the correct version. The problem of DDE not working can occur when you get the DLL from the wrong

In article <000001bf5a9b$8004eb60$0201a8c0@...>, UI-View <ui- view@...> writes Set "MCOM ON" on the TNC you are using with UI-View/WinPack. UI-View works differently to most

Jim, this may not have displayed because it is an invalid plot. ......................................~ ........................................~~ The "1" after the "W" represents a "good plot", but

Please excuse the ignorance, is there a FAQ about APRS and/or UI-View ? I've been subscribed to the list for a while now and have a few hundred questions I don't want to clog things up with ! TIA ---

Hi Maurice The output is in miles not Km I could change it to be either if so wished Could you send me a log file of some local traffic and I will investigate the problem for you. see UI- Does that

Hi, I use UI-view 2.16beta with AGWPE 2000 (latest version) I'm also running UI-path 1.6 and have the following problems: The distance to the other stations is not correct |ON4BAM|0,0|Heard

Hi Jim, In almost every case, such problems have been solved by performing either: RESTORE D (which restores your TNC to factory default settings...including the need to re-enter your MYCALL) -or-

Roger Barker wrote: Hi Roger, Nice catch! I may very well have an "incompatible" version of the .DLL. I installed from the Windows98 SR2 CD-ROM. Doing a search for DDEML.DLL, I find it in the

In the not too distant future I think the D7+GPS+single port laptop system will work fine, it just needs a little work for the next beta. Of course, this doesn't get over the original problem if you

A fudge - is to have the GPS connected to a TNC (MYCALL-7) and low power txrx running into a helical ant (or even dummy load). This TNC in GPS mode beacons your location. This part of the package

Hi All, Although I am a beginner to UI-View/APRS, I'm definitely not new to Packet! I have a Kantronics KPC-9612 and have set it up to beacon GPS information, however the packets it sends are not

In article <000d01bf5a8d$9c0009c0$23212121@down>, Andy Pritchard <apritch@...> writes To try and avoid a possible red herring - Could there be some confusion here between UI-Path and UI-MH?

In article <000801bf5a87$dd3cd720$a6e2abc3@default>, Mike.G1ZRN <mike.g1zrn@...> writes BPQ32 is for use with 32 bit programs. You can't use it with either UI-View or WinPack, because they

In article <PBDgukAr78d4EwR5@...>, Roger Barker <roger@...> writes [snip] And someone is now probably going to tell me that WinAPRS does it! ;-) So, I expect the real answer is

Hi Ev The ini file has no significance as for as im concerned. The file was a solution G6HIB found to make it work on his system. UI-Path should and does! work without a ini file if run from the

Hi, A bit off topic and I haven't had chance really to look back and see if this has been asked already.... Has anyone got a WORKING URL for BPQ32/BPQ4.09/BPQ4.09a please? Or maybe you could email it

Ok, Andy... You just *had* to post this information, didn't you? :o) I was about to scrap UI-View and UI-Path because I couldn't get it to work on my computer, and then you go and post some screen

Hi, For those using host software under UI-View, BPQ 32 bit software is available from the following site http://www.btinternet.com/~wyreforest.repeatergroup/wfrg.htm on the "Software page" I haven't

In article <001201bf5a66$a7783420$ca21883e@g7mvo2>, Mark Armfield G7MVO <mark@...> writes There probably isn't a problem. The chance of a ping getting through and the ack getting

Hi all Can someone tell me how to get UIVIEW to ping other stations, I can sometimes ping stations if I can hear them direct, but I have had no look using a reverse digi path. I just get the message