开云体育

Robert Sorry my mistake , its PA2 , pin 38 . There is an option to send the raw tension in the PA2 , so my idea is to use an external temperature sensor more accurately and make scaling . For

Not sure what you are asking. I am not sure what PIN 2 refers to - PA2 is pin 38 whih already has a temperature sensor on it on most configurations.? If using that sensor, you can use ^T (deg F) or

Friends Can I make some formula on the raw signal from TSTATUS , PIN 2, ^7 ? I mean , if I put a temperature sensor , is it possible to do some scaling? -- *PY5LF * *Luciano Fabricio*

If you have not done so, I suggest setting the CDMODE command to TONES. 73, Allen AF6OF

For a remote site like that, perhaps a timer on the power source could turn it off at midnight for a minute or two and re-power. Internal watchdog timers and such can force a re-boot of code, but

My solar digipeater has been working well since last summer 2020.? Earlier in May this year it went silent for 10 days or so, until I was able to gain access to my fire tower installation 90ft. up.?

Thanks for chiming in Byon, it looks like I have most everything set up, it would be nice to be able to have a status message without it being mic-e via TPROTOCOL but i don't think the locals will get

Sent from the all new AOL app for Android What I took from the photos was that he already has both the Keyboard/ Display interface board AND the 20x4 Hitachi 44780-compatible LCD display, both from

What I took from the photos was that he already has both the Keyboard/ Display interface board AND the 20x4 Hitachi 44780-compatible LCD display, both from Byonics. Assuming he has the needed TT4 to

To Joe, WB9SBD - You are wrong on all counts. You don't need to be concerned about the Group limits. Are you on a dial-up service? LOL I jest. Thank you, Joe, Group Owner

And all these Giant ridiculous images if it hasn't maxed out what the group will allow I bet it surely pushed the group to it's max limit. all those images could have been 10% of the size they are

I tried to trim this down to the new thread. Greg, From the diagrams in information posted, it appears you purchased the the Byonics LCD interface board and appear to be looking for an LCD display to

Yes, my apologies to the group! I should have started a new thread but my fat fingers got the best of me!?Tnx for the feedback.Greg Sent from the all new AOL app for Android On Tue, May 18, 2021 at

I am totally confused.??Steven VK2BOS was asking about using GPIO pins using over the air commands. It appears the thread was hijacked for lcd interfacing? Steve VK2BOS,Did you get an answer to your

Greg, It appears that you've hijacked the thread "Driving GPIO pins," and created a lot of confusion for those following the thread. Don't know why you'd do that without any mention why. As far as I

Tnx,?I forgot the hookup, thanks for the info!73 de Greg Sent from the all new AOL app for Android On Tue, May 18, 2021 at 4:17 PM, vhsproducts via groups.io<vhsproducts@...> wrote: It

It strikes me as a lot of work to replicate a product ( Well, hopefully) that you can have in your hands from Byonics in two days, but a Ham's quest for knowledge ( And getting stuff done less

Looks similar to this one https://cdn-shop.adafruit.com/datasheets/TC2004A-01.pdf Byonics makes a display and interface for the TT4 https://www.byonics.com/downloads/tt4_display_v1.3.pdf I don’t

I sent you these pics. LCD with some I/O connections I thought to display APRS data?Greg Sent from the all new AOL app for Android

Sent from the all new AOL app for Android On Tue, May 18, 2021 at 2:05 PM, Robert Bruninga<bruninga@...> wrote: I need more info.? What is that board? thanks Bob (in chemo fog)