开云体育

I run my WXtrax 24/7 on a solar system. It has run with a Baofang for probably 5 years. Get Outlook for Android<https://aka.ms/AAb9ysg> ________________________________ Sent: Sunday, December 31,

I don't have one of those cut-offs but in my solar go box is a solar controller and when it gets down to a certain voltage it will shut off. I have never noticed any issue of pulling power from any of

I've been using an Aprsworld APO3 battery cutoff for several years now and during that time i've had several TinyTrak units go bad and stop working. Do I just have a bad one or has anybody else had

I believe you are referring to the symbol table and getting the symbol you want. The symbol is not generated in the BTEXT.? There are specific "parameters" for that: These use normal characters, I

the Alt# I am using is [ALT94} Is there something else I shout use to get the symbol I need? And yes I see all the setting when I use the DISP command. Mike -N7ZEF

What is the [Alt#} command? You say you access the area where it wants the ? and esc3.? So you get into the Options Menu. You say you type disp and I assume you see all the settings. from the prompt

Thanks for the quick replys. However my question how can I type in the [alt #} command when it just ignores it? I can access the area where it want the ? and esc3 . I can do a disp. But when I go the

You mention TeraTerm, but not the interface device (computer serial device).Many users are powering the TT4 with the TT USB cable for changing settings. This works well for interfacing to the TT4,

You need to power cycle the tt4 while the connection is active. The lights dance then a ? Pops up and prompts you to push escape 3 times to get into the config. Onec in it then in the BTEXT and TSTAT

Howdy; I am trying to make some changes to my settings in TinyTrak4. I want to send the temp and voltage values when it beacons. I saw earlier using? ^ T and ^ V would do what I wanted. But I cannot

In case any of you were wondering, some of the parts for our MF-15 transmitters became extinct, and when we ran dry, so did the old MF-15. It was very much based on the TT3 encoder, and in fact, could

Enough! You two can go back and forth with direct messaging. This is a support group so support. Joe, N2QOJ - Owner / Moderator This thread is closed.

Ugh. “Political correctness” invoked in the face of a valid point, which is then willfully misinterpreted. Inappropriate, and boring. “Nobody’s treading on you, sweetie.” Where’s that

So you are saying that America does not need more digipeaters? (It does; fill-ins mostly) Or that I have a duty to be politically correct? I assume that this board is for the A PRS cognescenti, and

No, No, No, No!??? Keep in mind that for every digipeater you put on the air you HALVE the channel capacity!? That's right you 1/2 the number of packets the channel can pass. Digipeating is a

Hey folks! I just wanted to say thank you to everyone active here. Every day I get a new message from this group is a good day, because I know I'll learn something or see someone being really cool

Alan, ?First; Thanks for operating a fill--in digi,? America needs more digipeaters! If we ever reintroduce an MTT4B or MTT4BT, you can bet it will have a reset timer built in! 73, Allen AF6OF

I operate a fill-in digi, and use a smart plug to give me remote control if needed. After the second time over a couple of months my TT4B locked up, I programmed the smart plug to cycle the power

Ah, the deadly TT4 Hang....if it was a problem that I could replicate, it would probably be a lot easier to debug....sadly, its underlying cause has remained a complete mystery. It can take months to

I know a few people, myself included, who've had tt4s hang and become unresponsive until power cycled. It's a known issue that doesn't seem to have a solution other than power cycles. My buddy went