开云体育

Nico, I may have missed a few things in the last emails, so let me recapitulate a few things.? A:?If you have the Byonics USB cable you need to download and install the USB drivers from the Byonics

Excellent. Thanks much!

That should work. I would just leave it connected, make changes to the config, then after hitting <Write Config> disconnect and reconnect the cable. But your way works as well.

Ohboyohboy, that seems convoluted. Thank you for the reply, Rob. Not sure if I would have figured this out by myself via trial and error. I was not going to use the null-modem cable in addition to the

I assume the RTG-30 follows the Byonics standard of sending commands at startup (boot) for entering the bootloader. Typically, you would disconnect (cycle) the 12V power which has a regulator to the

I set up my old RTG-30 (bought in 2012) on my boat, and it's working fine. However, I need to change the settings to change the SSID and symbol from car to boat. When I initially tried to do this I

Hi Allen, Sorry to resurrect an old thread, but I just wanted to verify something after digging out my RTG-30. For your FINDU hack, do I just leave the "Edit Telemetry" all blank in TT3 and then just

Curious - did you put the old version back in the TT4 to see if it still works?If you don't have the firmware file, I can probably find it.OR ...Have you tried any versions between 0.6 and

Many thanks to all those who have replied with suggestions. I have re-installed the firmware ensuring that I have installed the correct firmware ( TT4_Alpha_v0.72_644.TT4). I have also been through

1. You say that pins 2 and 3 must be crossed on the programming cable and I understand that. But on both the PC pins and the MT8k pins you have pin 2 as Rx and pin 3 as Tx. ?Should it instead be pin

Rob, Thanks for jumping in there! I keep odd hours and I am not always around. Steve, Rob is right on everything. To directly address your question about connecting the MT-8000 FA to a USB-A

Rob, Yes, that is exactly what I’m looking for. Thank you - this helps a lot. But I do have a couple of questions. 1. You say that pins 2 and 3 must be crossed on the programming cable and I

I didn't see a response from Byonics, so I'll give some feedback.The MT8k connector is designed to connect to a GPS, so has the same pinout as the computer.You will need to cross pins 2 and 3 for the

Thank you Allen. I downloaded the manual, read it through and loaded the configuration software on my Windows 11 PC. I have a GPS module that I think will work with the 8000FA and several male and

It might be wise to make sure that you did not inadvertently install one of the .tt4 firmware versions for the MTT4B products, which are not compatible with the standard TT4 devices. 73, Allen AF6OF

No new PTT setting in 0.72. I'd recommend you to do a RESTORE to put the TT4 back to a factory state, and see if the problem still exists. It so, it would probably be a hardware issue, like the PTT

Well, the PTT activates (RED LED) so it isn't the CD line. FIRST - let me ask the most important question:?? >>> Did you save you settings (EXPORT) before updating the firmware? If the answer is

Hi, I have upgraded a Tiny Trak4 v7 board to version 0.72 firmware from 0.6. After configuring it I now have no PTT action at the radio. The red led comes on on the TT4 but it doesn't trigger the PTT

Almost forgot to answer my own question. Although I thought the TT4 expected hex values, the truth is the TT4 will decode the long string of text and break it into hex values, convert them to the

On the computer side, I shorted 4 to 6 (DTR / DSR)and 7 to 8 (RTS / CTS) and tried again => it worked as John said! I may never understand how an application has settings for a certain use, but