|
Hi
I have a Tek 465 unfortunately the? Level/Slope? pot/switch is not working.
Is there by any chace a parts unit out there?
I will take two if available..
Many thanks
regards
Jim
Ei2BB
|
Check here??. You need the part number, through.
No affiliation... bla bla bla...
From: James R. Bartlett
To: Tekscopes@...
Sent: Monday, October 8, 2012 3:50 PM
Subject: [TekScopes] 465 Pot
?
Hi
I have a Tek 465 unfortunately the? Level/Slope? pot/switch is not working.
Is there by any chace a parts unit out there?
I will take two if available..
Many thanks
regards
Jim
Ei2BB
|
Thanks Gala
Forgot the part number , it is 311-1192-00.
Will try that place.
Many thanks
Regads
Jim
?
?
?
?
?
?
Check here??. You need the part number, through.
No affiliation... bla bla bla...
?
Hi
I have a Tek 465 unfortunately the? Level/Slope? pot/switch is not working.
Is there by any chace a parts unit out there?
I will take two if available..
Many thanks
regards
Jim
Ei2BB
|
I?think I was looking for that same pot a year or two
ago?(if it had 10k in both halves) and none were to be found at Veronia
Northern or elsewhere.
An eBay seller had something close enough, but I forget the
exact details.
tom jobe...
?
?
?
toggle quoted message
Show quoted text
----- Original Message -----
Sent: Monday, October 08, 2012 6:24
AM
Subject: Re: [TekScopes] 465 Pot
?
Thanks Gala
Forgot the part number , it is
311-1192-00.
Will try that place.
Many thanks
Regads
Jim
?
?
?
?
?
On 8 October 2012 13:59, Gala Dragos <gala_dragos@...> wrote:
?
Check here??.
You need the part number, through.
No
affiliation... bla bla bla...
?
Hi
I have a Tek 465 unfortunately the? Level/Slope? pot/switch
is not working.
Is there by any chace a parts unit out there?
I will take two if available..
Many thanks
regards
Jim
Ei2BB
|
Thanks Tom,
It is a 10k pot with a switch at the rear.
Seems to be a scarce item, No luck so far.
But I live in hope. Must be some out there somewhere.
The part number is 311-1192-00.
Thanks again
Jim
?
I?think I was looking for that same pot a year or two ago?(if it had 10k in both halves) and none were to be found at Veronia Northern or elsewhere.
An eBay seller had something close enough, but I forget the exact details.
tom jobe...
?
?
?
----- Original Message -----
Sent: Monday, October 08, 2012 6:24 AM
Subject: Re: [TekScopes] 465 Pot
?
Thanks Gala
Forgot the part number , it is 311-1192-00.
Will try that place.
Many thanks
Regads
Jim
?
?
?
?
?
On 8 October 2012 13:59, Gala Dragos <gala_dragos@...> wrote:
?
Check here??. You need the part number, through.
No affiliation... bla bla bla...
?
Hi
I have a Tek 465 unfortunately the? Level/Slope? pot/switch is not working.
Is there by any chace a parts unit out there?
I will take two if available..
Many thanks
regards
Jim
Ei2BB
|
Oh yeah, last batch of those were "found" after I asked nicely the guy at Vernonia.
There are equivalents, in plastic through.
These are?scarce?because they have been used in so many?devices, Tek465, Tek475, I think that even Tek485, and a whole
bunch of other tek modules.
From: James R. Bartlett
To: TekScopes@...
Sent: Monday, October 8, 2012 5:12 PM
Subject: Re: [TekScopes] 465 Pot
?
Thanks Tom,
It is a 10k pot with a switch at the rear.
Seems to be a scarce item, No luck so far.
But I live in hope. Must be some out there somewhere.
The part number is 311-1192-00.
Thanks again
Jim
On 8 October 2012 15:04, Tom Jobe <tomjobe@...> wrote:
?
I?think I was looking for that same pot a year or two ago?(if it had 10k in both halves) and none were to be found at Veronia Northern or elsewhere.
An eBay seller had something close enough, but I forget the exact details.
tom jobe...
?
?
?
----- Original Message -----
Sent: Monday, October 08, 2012 6:24 AM
Subject: Re: [TekScopes] 465 Pot
?
Thanks Gala
Forgot the part number , it is 311-1192-00.
Will try that place.
Many thanks
Regads
Jim
?
?
?
?
?
On 8 October 2012 13:59, Gala Dragos <gala_dragos@...> wrote:
?
Check here?http://www.vernonianorthern.com/TekParts/Tek311Page.php?. You need the part number, through.
No affiliation... bla bla bla...
?
Hi
I have a Tek 465 unfortunately the? Level/Slope? pot/switch is not working.
Is there by any chace a parts unit out there?
I will take two if available..
Many thanks
regards
Jim
Ei2BB
|
On 10/08/2012 02:08 PM, Gala Dragos wrote:
?
Oh yeah, last batch of those were "found" after I
asked nicely the guy at Vernonia.
There are equivalents, in plastic through.
These are?scarce?because they have been used in so
many?devices, Tek465, Tek475, I think that even Tek485,
and a whole bunch of other tek modules.
How about the 465M?
If so, I may be able to help.
From: James R. Bartlett
To: TekScopes@...
Sent: Monday, October 8, 2012
5:12 PM
Subject: Re: [TekScopes] 465
Pot
?
Thanks Tom,
It is a 10k pot with a switch at the
rear.
Seems to be a scarce item, No luck so
far.
But I live in hope. Must be some out
there somewhere.
The part number is 311-1192-00.
Thanks again
Jim
On 8 October 2012 15:04, Tom Jobe <tomjobe@...>
wrote:
?
I?think I was looking for
that same pot a year or two
ago?(if it had 10k in both
halves) and none were to be
found at Veronia Northern or
elsewhere.
An eBay seller had something
close enough, but I forget the
exact details.
tom jobe...
?
?
?
----- Original Message
-----
Sent: Monday,
October 08, 2012 6:24 AM
Subject: Re:
[TekScopes] 465 Pot
?
Thanks Gala
Forgot the part number ,
it is 311-1192-00.
Will try that place.
Many thanks
Regads
Jim
?
?
?
?
?
On 8 October 2012
13:59, Gala Dragos <gala_dragos@...>
wrote:
?
Check
here??.
You need the
part number,
through.
No
affiliation...
bla bla bla...
?
Hi
I have a
Tek 465
unfortunately
the?
Level/Slope?
pot/switch is
not working.
Is there
by any chace a
parts unit out
there?
I will
take two if
available..
Many
thanks
regards
Jim
Ei2BB
|
Hi Bert,
They are the same in any of the 400 series scopes.
Be delighted if you had two.
Many thanks
Jim
?
On 10/08/2012 02:08 PM, Gala Dragos wrote:
?
Oh yeah, last batch of those were "found" after I asked nicely the guy at Vernonia.
There are equivalents, in plastic through.
These are?scarce?because they have been used in so many?devices, Tek465, Tek475, I think that even Tek485, and a whole bunch of other tek modules. How about the 465M?
If so, I may be able to help.
From: James R. Bartlett To: TekScopes@...
Sent: Monday, October 8, 2012 5:12 PM Subject: Re: [TekScopes] 465 Pot
?
Thanks Tom,
It is a 10k pot with a switch at the rear.
Seems to be a scarce item, No luck so far.
But I live in hope. Must be some out there somewhere.
The part number is 311-1192-00.
Thanks again
Jim
?
I?think I was looking for that same pot a year or two ago?(if it had 10k in both halves) and none were to be found at Veronia Northern or elsewhere.
An eBay seller had something close enough, but I forget the exact details.
tom jobe...
?
?
?
----- Original Message -----
Sent: Monday, October 08, 2012 6:24 AM
Subject: Re: [TekScopes] 465 Pot
?
Thanks Gala
Forgot the part number , it is 311-1192-00.
Will try that place.
Many thanks
Regads
Jim
?
?
?
?
?
?
Check here??. You need the part number, through.
No affiliation... bla bla bla...
?
Hi
I have a Tek 465 unfortunately the? Level/Slope? pot/switch is not working.
Is there by any chace a parts unit out there?
I will take two if available..
Many thanks
regards
Jim
Ei2BB
|
I have a resource that says it crosses to
1-28(R4/S4) 311-1192-00 Res.,Var,Nonwir : 10K Ohm, 20%, 1W w/ Switch (Centralab BA-232-001) Slope/Level ...
This switch is used in 7B53 and other 7000 series time bases. So is not rare I assume.
It appears to make some sense. However, I cannot verify it as I do not have access to any of the scopes in question. Therefore I do not know the form factor.
I can verify that the slope switch on a 7B53 (and others) is a 10K pot with an inner shaft on that is indeed a switch. The outer shaft (pot portion) around 1/8 to 1/4 inch the inner shaft (switch part) 1/8 or less.
Anyway trying to be helpful. Hopefully it is.
Rob
From: TekScopes@... [mailto:TekScopes@...] On Behalf Of Bert Haskins
Sent: Monday, October 08, 2012 3:19 PM
To: TekScopes@...
Subject: Re: [TekScopes] 465 Pot
On 10/08/2012 02:08 PM, Gala Dragos wrote:
Oh yeah, last batch of those were "found" after I asked nicely the guy at Vernonia.
There are equivalents, in plastic through.
These are scarce because they have been used in so many devices, Tek465, Tek475, I think that even Tek485, and a whole bunch of other tek modules.
How about the 465M?
If so, I may be able to help.
From: James R. Bartlett <james.r.bart@...>
To: TekScopes@...
Sent: Monday, October 8, 2012 5:12 PM
Subject: Re: [TekScopes] 465 Pot
Thanks Tom,
It is a 10k pot with a switch at the rear.
Seems to be a scarce item, No luck so far.
But I live in hope. Must be some out there somewhere.
The part number is 311-1192-00.
Thanks again
Jim
On 8 October 2012 15:04, Tom Jobe <tomjobe@...> wrote:
I think I was looking for that same pot a year or two ago (if it had 10k in both halves) and none were to be found at Veronia Northern or elsewhere.
An eBay seller had something close enough, but I forget the exact details.
tom jobe...
----- Original Message -----
From: James R. Bartlett
To: TekScopes@...
Sent: Monday, October 08, 2012 6:24 AM
Subject: Re: [TekScopes] 465 Pot
Thanks Gala
Forgot the part number , it is 311-1192-00.
Will try that place.
Many thanks
Regads
Jim
On 8 October 2012 13:59, Gala Dragos <gala_dragos@...> wrote:
Check here . You need the part number, through.
No affiliation... bla bla bla...
From: James R. Bartlett <james.r.bart@...>
To: Tekscopes@...
Sent: Monday, October 8, 2012 3:50 PM
Subject: [TekScopes] 465 Pot
Hi
I have a Tek 465 unfortunately the Level/Slope pot/switch is not working.
Is there by any chace a parts unit out there?
I will take two if available..
Many thanks
regards
Jim
Ei2BB
|
Hi Rob,
Thanks for your input.
The information on the pot/switch is :
S.C. Co. Type 10K 19-7330???? 311-1192-00
The switch is marked ;??? S.C. Type? PE? B-16????? 1 Amp 125 Volt AC
UND LAB Inc Insp.
It is interesting that the pot has the Tektronix part number stamped on it.
Your information certainly widened the field so maybe I can get hold of a junker plug in.
Your description of the construction is spot on. 1/8 inch? outer shaft? the inner shaft appears to be a bit bigger than 1/16 inch, body diameter is .640 in?.
I will? start to search the Net.
Thanks again Rob.
Best wishes
Jim
Ei2BB
?
?
?
I have a resource that says it crosses to
1-28(R4/S4) 311-1192-00 Res.,Var,Nonwir : 10K Ohm, 20%, 1W w/ Switch (Centralab BA-232-001) Slope/Level ...
This switch is used in 7B53 and other 7000 series time bases. So is not rare I assume.
It appears to make some sense. However, I cannot verify it as I do not have access to any of the scopes in question. Therefore I do not know the form factor.
I can verify that the slope switch on a 7B53 (and others) is a 10K pot with an inner shaft on that is indeed a switch. The outer shaft (pot portion) around 1/8 to 1/4 inch the inner shaft (switch part) 1/8 or less.
Anyway trying to be helpful. Hopefully it is.
Rob
From: TekScopes@... [mailto:TekScopes@...] On Behalf Of Bert Haskins
Sent: Monday, October 08, 2012 3:19 PM
To: TekScopes@...
Subject: Re: [TekScopes] 465 Pot On 10/08/2012 02:08 PM, Gala Dragos wrote: Oh yeah, last batch of those were "found" after I asked nicely the guy at Vernonia. There are equivalents, in plastic through.
These are scarce because they have been used in so many devices, Tek465, Tek475, I think that even Tek485, and a whole bunch of other tek modules. How about the 465M? If so, I may be able to help. From: James R. Bartlett < james.r.bart@...>
To: TekScopes@... Sent: Monday, October 8, 2012 5:12 PM Subject: Re: [TekScopes] 465 Pot Thanks Tom, It is a 10k pot with a switch at the rear.
Seems to be a scarce item, No luck so far. But I live in hope. Must be some out there somewhere. The part number is 311-1192-00. Thanks again Jim On 8 October 2012 15:04, Tom Jobe < tomjobe@...> wrote:
I think I was looking for that same pot a year or two ago (if it had 10k in both halves) and none were to be found at Veronia Northern or elsewhere. An eBay seller had something close enough, but I forget the exact details.
tom jobe... ----- Original Message ----- From: James R. Bartlett To: TekScopes@... Sent: Monday, October 08, 2012 6:24 AM
Subject: Re: [TekScopes] 465 Pot Thanks Gala Forgot the part number , it is 311-1192-00. Will try that place. Many thanks Regads Jim On 8 October 2012 13:59, Gala Dragos < gala_dragos@...> wrote:
Check here . You need the part number, through. No affiliation... bla bla bla...
From: James R. Bartlett < james.r.bart@...> To: Tekscopes@... Sent: Monday, October 8, 2012 3:50 PM
Subject: [TekScopes] 465 Pot Hi I have a Tek 465 unfortunately the Level/Slope pot/switch is not working. Is there by any chace a parts unit out there? I will take two if available.. Many thanks regards
Jim Ei2BB
|
If I am not mistaken I have a junked/part-er 7000 series Time Base. Respond off list with address and if I do I¡¯ll send it gratis as long as you¡¯re willing to report success or failure with it for the scope in question. ? That way we can benefit the entire community. ? I hope this finds you well Rob
toggle quoted message
Show quoted text
From: TekScopes@... [mailto:TekScopes@...] On Behalf Of James R. Bartlett
Sent: Tuesday, October 09, 2012 5:59 AM
To: TekScopes@...
Subject: Re: [TekScopes] 465 Pot?
The information on the pot/switch is : S.C. Co. Type 10K 19-7330???? 311-1192-00 The switch is marked ;??? S.C. Type? PE? B-16????? 1 Amp 125 Volt AC It is interesting that the pot has the Tektronix part number stamped on it. Your information certainly widened the field so maybe I can get hold of a junker plug in. Your description of the construction is spot on. 1/8 inch? outer shaft? the inner shaft appears to be a bit bigger than 1/16 inch, body diameter is .640 in?. I will? start to search the Net. On 9 October 2012 01:06, Rob <rgwood@...> wrote: ? I have a resource that says it crosses to
1-28(R4/S4) 311-1192-00 Res.,Var,Nonwir : 10K Ohm, 20%, 1W w/ Switch (Centralab BA-232-001) Slope/Level ...
This switch is used in 7B53 and other 7000 series time bases. So is not rare I assume.
It appears to make some sense. However, I cannot verify it as I do not have access to any of the scopes in question. Therefore I do not know the form factor.
I can verify that the slope switch on a 7B53 (and others) is a 10K pot with an inner shaft on that is indeed a switch. The outer shaft (pot portion) around 1/8 to 1/4 inch the inner shaft (switch part) 1/8 or less.
Anyway trying to be helpful. Hopefully it is.
Rob
From: TekScopes@... [mailto:TekScopes@...] On Behalf Of Bert Haskins
Sent: Monday, October 08, 2012 3:19 PM
To: TekScopes@...
Subject: Re: [TekScopes] 465 Pot
On 10/08/2012 02:08 PM, Gala Dragos wrote:
Oh yeah, last batch of those were "found" after I asked nicely the guy at Vernonia.
There are equivalents, in plastic through.
These are scarce because they have been used in so many devices, Tek465, Tek475, I think that even Tek485, and a whole bunch of other tek modules.
How about the 465M?
If so, I may be able to help.
From: James R. Bartlett <james.r.bart@...>
To: TekScopes@...
Sent: Monday, October 8, 2012 5:12 PM
Subject: Re: [TekScopes] 465 Pot
Thanks Tom,
It is a 10k pot with a switch at the rear.
Seems to be a scarce item, No luck so far.
But I live in hope. Must be some out there somewhere.
The part number is 311-1192-00.
Thanks again
Jim
On 8 October 2012 15:04, Tom Jobe <tomjobe@...> wrote:
I think I was looking for that same pot a year or two ago (if it had 10k in both halves) and none were to be found at Veronia Northern or elsewhere.
An eBay seller had something close enough, but I forget the exact details.
tom jobe...
----- Original Message -----
From: James R. Bartlett
To: TekScopes@...
Sent: Monday, October 08, 2012 6:24 AM
Subject: Re: [TekScopes] 465 Pot
Thanks Gala
Forgot the part number , it is 311-1192-00.
Will try that place.
Many thanks
Regads
Jim
On 8 October 2012 13:59, Gala Dragos <gala_dragos@...> wrote:
Check here . You need the part number, through.
No affiliation... bla bla bla...
From: James R. Bartlett <james.r.bart@...>
To: Tekscopes@...
Sent: Monday, October 8, 2012 3:50 PM
Subject: [TekScopes] 465 Pot
Hi
I have a Tek 465 unfortunately the Level/Slope pot/switch is not working.
Is there by any chace a parts unit out there?
I will take two if available..
Many thanks
regards
Jim
Ei2BB
|
