Re: Looking for Sony-Tektronix 318 Logic Analyser Operator's Guide
To all who responded on this topic: H?kan Hintze (he proves to be an open treasure pit again!) sent me a scan of the 318|338 operator's manual. I will upload it to TekWiki (another invaluable
By
Raymond Domp Frank
·
#155263
·
|
Re: 2467B geometry
Chuck: UGH! I understand your frustration. This is the best setting of GEOM = full CCW? The 4 I have are either 100% or just slightly off grid. Only the 2467B is noticable. Tip on scope photo
By
Jean-Paul
·
#155262
·
|
Re: Help needed to repair the Telequipment D54 Oscilloscope
Did you ever make any headway on this? ..I've got a 'functional' D54 so maybe ...stare and compare Jim
By
Jim Tibbits
·
#155261
·
|
Re: DC508 HELP with PHOTOS option 7
Hi Dennis, Se page 17-3 http://dadaelectronics.com.au/doc/Audio/Tektronix/TM500/TM5X_RIB_FREE.pdf You need to interconnect 14B, 15B, 16B, 17B, 18B and 18A Best regards Miguel -----Mensaje
By
Miguel Work
·
#155260
·
|
Re: Looking for Sony-Tektronix 318 Logic Analyser Operator's Guide
Thanks for considering that, Kyle, You probably understood that I'm not looking for the self-evident parts in a user manual but hoping for some nice surprises. It seems likely that the 318 has more
By
Raymond Domp Frank
·
#155259
·
|
Re: Tek Blue Paint - the story goes on ... :-)
If you are worried about attacking the aluminum, avoid the use of oven cleaner as posted above. Oven cleaner is based on sodium hydroxide (lye). While it is not problem for cast iron as in a metal
By
ditter2
·
#155258
·
|
Re: DC508 HELP with PHOTOS option 7
Hi Miguel, Because of your posts about Option 7 I decided to finish hooking up my DC508 Option 7 to my TR502 Tracking Generator. The one thing I am missing is the wiring diagram for the TM503 Main
By
Dennis Tillman W7pF
·
#155257
·
|
Re: Looking for Sony-Tektronix 318 Logic Analyser Operator's Guide
Hi Raymond, I have a 318, but don¡¯t recall if there¡¯s a manual in the top zippered pouch. I¡¯ll check and if so look at how feasible it would be to scan it. Personally, I¡¯ve never looked for a
By
Kyle Rhodes
·
#155256
·
|
Re: Looking for Sony-Tektronix 318 Logic Analyser Operator's Guide
And one more point, Roy: The short answer is: dunno. It's my experience that often, wading through an operator manual saves time in getting acquainted with a piece of equipment, even if I know how it
By
Raymond Domp Frank
·
#155255
·
|
Re: Looking for Sony-Tektronix 318 Logic Analyser Operator's Guide
Hi again Roy, 1 mega-sample? Raymond
By
Raymond Domp Frank
·
#155254
·
|
Re: Looking for Sony-Tektronix 318 Logic Analyser Operator's Guide
Hi Roy, You're frighteningly close to touching on the very reason for groups like this to exist... Raymond
By
Raymond Domp Frank
·
#155253
·
|
Re: 577 Curve tracer ringing CRT and noisy step generator
Power supply measurements not bad +12V measured +11.98DC 0.001AC ripple -12V measured -11.73DC 0.001AC ripple +200V measured 211.4VDC 0.386AC ripple -30V measured -29.97DC 0.001AC ripple +30V measured
By
DW
·
#155252
·
|
Re: Looking for Sony-Tektronix 318 Logic Analyser Operator's Guide
Well, if you regard signature analysis as fun, then you can do that. The 308 was more limited, but if you're looking at vintage electronics that uses signature analysis, that's not a bad thing to have
By
Harvey White
·
#155251
·
|
Re: Looking for Sony-Tektronix 318 Logic Analyser Operator's Guide
Hi: It seems the Army one has a reasonable operator's section (Chapter 4?). What part isn't detailed enough? My question is why: what can one do with a 50 MHz (1 mega-sample) logic analyzer...that you
By
Roy Thistle
·
#155250
·
|
Re: Tektronix 015-0580-00 Pocket Signal Generator
This generator was designed as a sales tool, to be used to demonstrate a particular feature in the TDS600 series which had a competitive advantage at the time. I don't recall the feature, perhaps
By
ditter2
·
#155249
·
|
Re: WTB 7104 Instruction Manual Revised Jul 1987 (070-2314-00)
Bill I (and I am sure Q-Service does too) appreciate your moral character... 8^) Dave ArtekManuals -- Dave Manuals@... www.ArtekManuals.com
By
Dave / NR1DX
·
#155248
·
|
Re: WTB 7104 Instruction Manual Revised Jul 1987 (070-2314-00)
Dave: After researching the source of this 7104 manual FEB 1989 I see that I did buy it from QSERVICE Nikolaos Kapetanakis for $US 9.49. So I don't feel good at all in sending this PDF to anyone
By
Bill
·
#155247
·
|
Re: Off Topic -- DC508 replacement display
Good job!!!!! -----Mensaje original----- De: [email protected] [mailto:[email protected]] En nombre de scskits Enviado el: martes, 9 de octubre de 2018 23:47 Para: [email protected] Asunto:
By
Miguel Work
·
#155246
·
|
Re: DC508 HELP with PHOTOS option 7
Thanks!! Now is working, some traces in option board were shorted, manufacturing defect in PCB, I was going crazy, I almost did not see it. Some photos /g/TekScopes/album?id=86699
By
Miguel Work
·
#155245
·
|
Re: PG506 Repair - 20v & 50v standard amplitude is low
Solved.... After tearing into the PG506 for a while and re-verifying the divider networks to no avail, I discovered a bad BNC cable between the 3456A and GenCal resistor decade I was using. The darn
By
N3SWR
·
#155244
·
|