开云体育

-----Original Message-----
From: Miroslav Pokorni [mailto:mpokorni2000@...]
Sent: Tuesday, January 08, 2002 5:16 AM
To: TekScopes@...
Subject: Re: [TekScopes] WTD: Manual for C1002 Camera


I do not quite understand why do you want to sell that camera if you do
not have manual, but if you persist, I might consider buying it. What is
your asking price?

Do you know what is difference between C1001 and C1002? I just assumed
that both have 9 pin D connector for all connections, but maybe that is not
so.

Regards
Miroslav Pokorni
----- Original Message -----
From: Richard W. Solomon
To: TekScopes@...
Sent: Monday, January 07, 2002 3:27 PM
Subject: RE: [TekScopes] WTD: Manual for C1002 Camera


I "reverse engineered" the power connector and figured out the pin-out.
So
far I have not
gotten anywhere on getting a manual. If all else fails, I'll probably
just
put it up for sale
and move on to something else.
I got this with a lot of Tektronix scope cameras, got two C-50's left
and
this orphan.

Regards,
Richard S.
-----Original Message-----
From: Miroslav Pokorni [mailto:mpokorni2000@...]
Sent: Monday, January 07, 2002 12:05 AM
To: TekScopes@...
Subject: Re: [TekScopes] WTD: Manual for C1002 Camera


Hello Dick,

I own two of C1001 cameras and do not have any documentation. Perhaps
we
can share notes.

So far, I found out that camera part was made by NEC and puts out an
NTSC
signal. There are several adapters to mount camera to scope, probably
the
most useful are:

1.. 016-0248-01 for small screen 7000 series scopes (not 7600,
though
and 7600 is not recommended; probably image is too big)
2.. 016-0269-03 for 2400 and 'new' 400 (465)
3.. 016-0306-01 for 'old' 400 series (485, 454 etc.)
I am looking for #1 adapter while #2 came with one of cameras. I am
also
looking for documentation and selected accessories; I do not think that
original board for PC would be very useful, that might be a pre-ISA slot
and
even if you have the slot in your PC, drivers might be missing or
incompatible with available Wander from Redmond.

What I found so far is:

1.. The 9-pin connector takes in 12 V, around 300 mA at pins 1
(positive) and 3 (ground) and signal is on pins 4 (shield/ground) and 5
(video); there are two other pins used which bring in calibration
voltages
and go only to BNC and two test points.
2.. Someone on this forum suggested to use 'Snappy' for frame
capture;
that device is available on e-bay for around $10, but manufacturer seems
to
be out of business. I played a bit with this camera, with limited
success.
The Snappy has a 'monitor' mode, a quasi real time but that was not good
enough to adjust focus, so I set focus to infinite and looked at the
picture
of nearby window; that way basic camera operation was verified. With
great
difficulties I managed to focus camera for oscilloscope image. Adjusting
light intensity exhausted last shreds of my patience and now camera has
to
wait. However, the best results I got when TV receiver's video input was
used, a real real-time image.
I would like to find out how this camera or frame capture board were
triggered to capture desired frame. I presume that was done by trailing
edge
of scope gate signal.

Out of curiosity, how much did you pay for your camera? The first one
I
paid around $70 (with shipping) while second one was mine for $20 (with
shipping) and I do not see the difference. The cheaper one came with
scope
adapter and a cable (9 pin male D connector on both ends) and is higher
serial number; it is just as you would expect on e-bay, no rime.

I tried this forum for more information or parts, but no luck so far.
Let's hope you have better luck.

Regards
Miroslav Pokorni

----- Original Message -----
From: w1ksz
To: TekScopes@...
Sent: Wednesday, January 02, 2002 3:45 PM
Subject: [TekScopes] WTD: Manual for C1002 Camera


I picked up this TEK Video Camera (mounts on Scope face).
Does anyone have a manual I can buy or copy ? Or have any info on
this camera ?

Thanks, Dick, W1KSZ


Yahoo! Groups Sponsor
ADVERTISEMENT




To unsubscribe from this group, send an email to:
TekScopes-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.






Yahoo! Groups Sponsor
ADVERTISEMENT




To unsubscribe from this group, send an email to:
TekScopes-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.






Yahoo! Groups Sponsor
ADVERTISEMENT




To unsubscribe from this group, send an email to:
TekScopes-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.






Yahoo! Groups Sponsor
ADVERTISEMENT




To unsubscribe from this group, send an email to:
TekScopes-unsubscribe@...



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.