开云体育

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. SubaruVanagon
  2. Topics

Warren’s Conversion - Clutch and Pressure Plate, Fuel Tank Refresh, and Coolant Pipes

 

I really doubt the veracity of any warranty from any manufacturer on any of the parts I purchase. ?It’s just a reality of today’s world that many (most) big companies just don’t care. ?So I approach every purchase as a “buyer beware” type of thing.
?
John, I bled my tensioner as well, but it sure was a slow process and I’m not sure I went as slow as they recommend. ?But remember, if you don’t install it right away, I think you should store it right side up (as in the orientation that it will be installed), just to keep any air bubbles from migrating to the wrong place.
--
Warren
89 Westy?
88 Tintop
70 Westy
 

Sure, but good luck with any kind of warranty claim. I showed Gates a collapsed cogged idler from a Gates Kit and all I got was crickets. It was SKF too! Luckily, no engine damage.
 

开云体育

Bled my new tensioner today. I’ve never heard of doing this but apparently it’s a thing. Tried the old one too as a test and it was a bit easier to compress but not much. Likely was ok.?


On Wed, Mar 12, 2025 at 9:15?PM SubieVanagon via groups.io <wklail@...> wrote:
That looks great! ?Let us know how well it works, how difficult to install, etc.?
--
Warren
89 Westy?
88 Tintop
70 Westy

IMG_1705.jpeg
IMG_1704.jpeg

 

Did mine like that 13? years ago and no issues..Just did it on a friends?van last week, also smooth install.? Its nice since its all pre-set?tp push?up, just connect the one crossover and since its flexible its easy.

Andy Vanis

USA and Whatsapp +1(505) 304-5306



On Wed, Mar 12, 2025 at 10:15?PM SubieVanagon via <wklail=[email protected]> wrote:
That looks great!? Let us know how well it works, how difficult to install, etc.?
--
Warren
89 Westy?
88 Tintop
70 Westy
 

That looks great! ?Let us know how well it works, how difficult to install, etc.?
--
Warren
89 Westy?
88 Tintop
70 Westy
 

IMG_20150215_142133.jpg

Andy Vanis

USA and Whatsapp +1(505) 304-5306



On Wed, Mar 12, 2025 at 10:05?PM Andrew Vanis <andrewvanis@...> wrote:
a permanent fuel tank solution is possible

IMG_20150215_124959.jpg
IMG_20150208_173614.jpg

Andy Vanis

USA and Whatsapp +1(505) 304-5306



On Wed, Mar 12, 2025 at 8:10?PM SubieVanagon via <wklail=[email protected]> wrote:
After much struggling I got the fuel tank removed.? My original intention was to remove it in order to install the stainless coolant lines, but as I got into the job it was obvious that all the hoses and fittings needed to be replaced.? I’m thinking there won’t be a better time than now to take this on.? So I will replace all the fittings and hoses.? This is a California bus so there is no rust on the tank at all ( just lots of dirt).? Tomorrow I will seal it up and powerwash it and paint it with a Rustoleum paint of some sort.? Some people paint them with high zinc content paints, but I’m not sure that is necessary.
?
--
Warren
89 Westy?
88 Tintop
70 Westy
 

a permanent fuel tank solution is possible

IMG_20150215_124959.jpg
IMG_20150208_173614.jpg

Andy Vanis

USA and Whatsapp +1(505) 304-5306



On Wed, Mar 12, 2025 at 8:10?PM SubieVanagon via <wklail=[email protected]> wrote:
After much struggling I got the fuel tank removed.? My original intention was to remove it in order to install the stainless coolant lines, but as I got into the job it was obvious that all the hoses and fittings needed to be replaced.? I’m thinking there won’t be a better time than now to take this on.? So I will replace all the fittings and hoses.? This is a California bus so there is no rust on the tank at all ( just lots of dirt).? Tomorrow I will seal it up and powerwash it and paint it with a Rustoleum paint of some sort.? Some people paint them with high zinc content paints, but I’m not sure that is necessary.
?
--
Warren
89 Westy?
88 Tintop
70 Westy
 

Please let me know if any of my experiences in this process can be of benefit to you! ?Essentially all of us doing these conversions are in this together.?
--
Warren
89 Westy?
88 Tintop
70 Westy
 

开云体育

Oh man you’re not wrong. I put in my hopefully last dealer order this week. Some sensors, new coolant bypass pipe, the two small throttle body hoses etc and also got all of my new timing belt components. Pretty excited to slap the heads on.?

Sure would be nice if someone sold an actual complete kit, some of the items they don’t include are baffling. At the end of the day I went RMW because I didn’t like some of the things about the SC one, so I guess I shouldn’t complain.


On Wed, Mar 12, 2025 at 7:03?PM SubieVanagon via groups.io <wklail@...> wrote:
The instructions from RMW so far seem to be pretty good. ?I got the clutch kit from RMW, which is a Sachs kit. ?It came with the clutch, pressure plate, release bearing, pilot bearing, and the spline alignment tool. ?The pilot bearing is not needed because RMW’s flywheel already has the pilot bearing installed. As I mentioned, there was no suggestion to use blue thread locker on the bolts, but I did it anyway. ?
?
I originally ordered my motor mounts from eBay but they were not the same. ?Now I can’t remember where I got the ones that actually matched the originals from the Subaru. ?But they were about $60 for the pair if I recall correctly. ?
?
The one on the left was the one from eBay. ?It was listed as the same, but it was not the same size. ?It might have worked but I didn’t want to chance it so I returned them.
?
?
The mounts I eventually purchased were identical to the originals. ?I will try to figure out where I purchase them. ?So many purchases!!!?
?
Warren
89 Westy?
88 Tintop
70 Westy
 

John A. ?At what stage are you in your conversion? ?Seems like we’re running parallel projects here. ?I appreciate your comments and feedback. ?
--
Warren
89 Westy?
88 Tintop
70 Westy
 

After much struggling I got the fuel tank removed. ?My original intention was to remove it in order to install the stainless coolant lines, but as I got into the job it was obvious that all the hoses and fittings needed to be replaced. ?I’m thinking there won’t be a better time than now to take this on. ?So I will replace all the fittings and hoses. ?This is a California bus so there is no rust on the tank at all ( just lots of dirt). ?Tomorrow I will seal it up and powerwash it and paint it with a Rustoleum paint of some sort. ?Some people paint them with high zinc content paints, but I’m not sure that is necessary.
?
--
Warren
89 Westy?
88 Tintop
70 Westy
 

The instructions from RMW so far seem to be pretty good. ?I got the clutch kit from RMW, which is a Sachs kit. ?It came with the clutch, pressure plate, release bearing, pilot bearing, and the spline alignment tool. ?The pilot bearing is not needed because RMW’s flywheel already has the pilot bearing installed. As I mentioned, there was no suggestion to use blue thread locker on the bolts, but I did it anyway. ?
?
I originally ordered my motor mounts from eBay but they were not the same. ?Now I can’t remember where I got the ones that actually matched the originals from the Subaru. ?But they were about $60 for the pair if I recall correctly. ?
?
The one on the left was the one from eBay. ?It was listed as the same, but it was not the same size. ?It might have worked but I didn’t want to chance it so I returned them.
?
?
The mounts I eventually purchased were identical to the originals. ?I will try to figure out where I purchase them. ?So many purchases!!!?
?
Warren
89 Westy?
88 Tintop
70 Westy
 

开云体育

How do you feel about the instructions so far? I’m not a fan. Also what clutch did you use and lastly where did you get the engine mounts? The dealer wants a million dollars for them here.

Thank you sir, great write up?


On Wed, Mar 12, 2025 at 12:59?PM SubieVanagon via groups.io <wklail@...> wrote:
Today I started to remove the fuel tank and those pesky expansion tanks. ?I got the fuel filler neck out after shedding a bit of blood due to a nice scrape. ?The grommet on top of the expansion tank was rotted off and actually down inside the tank. ?No wonder I was always smelling gas. ?
?
So next is removing the fuel tank itself and the plastic coolant pipes that run front to back. ?I believe the stainless pipes I purchased from Van Cafe are made to work with their conversion kit. ?
?
In the meantime, I installed the clutch and pressure plate on the Subaru engine, torqued the bolts evenly to 22 ft lbs and, although I did not see it recommended in the RMW literature, I used a bit of blue thread locker on them. ?
?
--
Warren
89 Westy?
88 Tintop
70 Westy
 

Today I started to remove the fuel tank and those pesky expansion tanks. ?I got the fuel filler neck out after shedding a bit of blood due to a nice scrape. ?The grommet on top of the expansion tank was rotted off and actually down inside the tank. ?No wonder I was always smelling gas. ?
?
So next is removing the fuel tank itself and the plastic coolant pipes that run front to back. ?I believe the stainless pipes I purchased from Van Cafe are made to work with their conversion kit. ?
?
In the meantime, I installed the clutch and pressure plate on the Subaru engine, torqued the bolts evenly to 22 ft lbs and, although I did not see it recommended in the RMW literature, I used a bit of blue thread locker on them. ?
?
--
Warren
89 Westy?
88 Tintop
70 Westy

21 - 34 of 34