开云体育

I have a Shari! Question on programming, The first option of programming is Channel Spacing... the options are 0 and 1, what is the effect of each?? My Second question is the Squelch Setting .. you have options of 1-9, is 1 low (tight) and 9 High (Lose)? I cant find this info anywhere..... Thanks....

This sounds like a fun addition to my micro-shack and will give my unloved Pi 2 something to do (hi). Steve Matzura WB2KTV

If you have a Shari you want to part with, contact me off of the list. email good on QRZ. jb N4NQY

Our order for assembled SHARI SMT boards is now in production. The good news is the bare PC board fabrication is complete. However the order shows a projected PCB SMT assembly time of 55 to 70 days. Steve - N8AR

While the world melts down due to COVID-19, and we wait for the supply of SHARI's to come back, I wanted to ask a quick question. Can the SHARI be used with a standard USB hub? I'm hoping to order one, but I'm wanting to mount mine on top to make it a bit more portable and prevent damage to the USB connectors. I wasn't sure how the two USB connections were set up, if one was power and the other was control, or what. I plan to use it to replace the Motorola on my "portable" Allstarlink hub which uses the Hamvoip image. Mike

Hello, This email message is a notification to let you know that the following files have been uploaded to the Files area of the [email protected] group. /Setting the RX Level in HamVOIP Allstar.pdf Uploaded By: N8AR <n8ar73@...> Description: This is a short document which describes the method I use to set the RX level in HamVOIP Allstar to optimize DTMF decoding. Cheers, The Groups.io Team

Hey guys, Anyone know the numbers you use for setting PL on the shari? I wanna change the pl on my node, but forgot how to do it. Cheers, Jed

Hey guys, So i'm going through the 8181-prog. I got everything, but it asked for a volume level, what should i set that as? Thanks, Jed

Hello, This email message is a notification to let you know that the following files have been updated in the Files area of the [email protected] group. /SHARI Allstar Node Setup Procedure-Version 1.2.pdf Uploaded By: N8AR <n8ar73@...> Description: This is Version 1.2 of a procedure to setup an Allstar Node using SHARI and the HamVOIP image. Pay particular attention to the Channel Setting of "1" when programming the SA-818. Cheers, The Groups.io Team

Hello, This email message is a notification to let you know that the following files have been uploaded to the Files area of the [email protected] group. /shari-pixx-prog Uploaded By: N8AR <n8ar73@...> Description: This file (shari-pixx-prog) is the 818-prog Python program we have been using to program SHARI with the added capability to issue the "Close Tail Tone" command. Since this command turns on/off CTCSS reverse burst, the setting in the program is called CTCSS Reverse Burst. Setting it to 0 means no reverse burst (and thus a squelch tail) while setting it to '1' turns on reverse burst. Cheers, The Groups.io Team

There is a discussion on the HamVOIP ARM-allstar list about how to remove the 'squelch crash' when using SHARI. This is typically done using CTCSS with reverse burst. For this to work, the radio you are using to talk to your SHARI must support reverse burst. The SA818 used in SHARI can be programmed to send/not send reverse burst but that command is not included in the 818-prog program that we have been using to program SHARI. It turns out that the default setting for the SA818 in SHARI is reverse burst turned on. I use a Kenwood TH-F6A and hear no squelch tail with it turned on. I have modified the 818-prog program to include the capability to set reverse burst to off/on. When using the program '0' means no CTCSS reverse burst and '1' means send CTCSS reverse burst. The new program is called shari-pixx-prog and has been uploaded to the File section of this group. If you want to experiment with reverse burst, you can upload it to the /usr/local/sbin folder of your Pi using WinSCP. After you upload it be sure to make it executable by right clicking on it from within WinSCP and checking the three executable boxes (boxes labeled X). You run the program the same way you run 818-prog. Steve - N8AR

Hello everyone, I put together a 2 meter shari kit and I can not get the transceiver chip to #program using the #818-prog. It seems to be stuck on Sending Freq information Any ideas what could be the cause of this or where to start to trouble shoot it? The Pi sees the SHARI as a serial device on ttyUSB0 csh341 uart converter attached to ttyUSB0 -- -Edmund Liddle, KE8ANU

I'm looking to purchase two SHARI's, namely one 2m and one 70cm. Is there any issue with running two on a single Pi? Reason being there are times when I will have a 2 meter only radio, so I kind of want to have the ability to choose either one. The 70cm is also going to function as a repeater from my mobile at times, if I go through with it. I may change plans before then, but just curious.

Steve N8AR, I see the Shari uses the FL1 Low Pass filter device to suppress harmonics from the SA-818 UHF Module. I was wondering what amount of suppression you get from this device? Thanks, Vince - NY5AR

Hello, I received the 2 meter and 70cm shari kits this week. I put the 2 meter and 70cm antennas on my MFJ antenna analyzer. The 2 meter antenna has a high SWR 10:1 at 146.52 on the 2 meter ham band. The antenna is labeled for 154 MHz. The 70cm antenna is designed for the lower end of the 70cm band it is labeled for 433MHz. at 446.00 the SWR is greater than 5:1 I was wondering how well the transceiver chips will handle a high SWR on the 2 meter band and 70cm band. -- -Edmund Liddle, KE8ANU

I received my Pi4U yesterday (assembled unit) and I followed the instructions and was up and running in a half hour. I did already have a Node Number and Password however. I did not even have to make audio adjustment. Many thanks and I have another way to be un-bored during COVID-19 restrictions. -- jb N4NQY

I am wanting to setup a shari to use DCS instead of PL. In all the docs, and scripts, its indicated that you use a 4 digit number to enter the pl tone. when I look at the SA818 manual, it looks like all the dcs codes are 6 digit hex. 025 540F6B Will those codes work if entered in to the script, or does something else need to be done?

Added 3 1000 word photo's to PHOTO area. #1 - SA818 soldering jig. #2 - Smoke Test 5.03V #3 - Smote Test 0.14A.