|
Locked
Configuring AURSINC Shari PiHat - Portable SR-FRS1W Ham Allstar Radio Interface Compatible with Raspberry Pi 2/3/4
#Allstar_Setup
Hello fellow members,
My first time here and I need your help. I recently purchased the AURSINC Shari PiHat - Portable SR-FRS1W Ham Allstar Radio Interface Compatible with Raspberry Pi 2/3/4 from amazon. I am using the latest image from hamvoip,?RPi-Z2W-2-3-4_V1.7-01_Allstar with my RPi 3B+. Following the setup procedures found in HamVOIP, I was able to run through all the configurations except the SA818 Program with the following error:?? Sending Frequency, Sub Audible Tone, and Squelch Information...
Frequency, Sub Audible Tone, and/or Squelch information were incorrect
Command Sent:
? ? ? ? AT+DMOSETGROUP=1,438.0155,438.0155,0000,1,0000
Any idea? I captured the screen from MobaXterm, see below: . ? |
|
Re: Can not change frequency or CTSS code
What Ed said is right on the money and I wish I would have known about kitsforhams.com when I bought my Chinese knockoff. I haven't any problems with mine and it is in band, but you can tell the quality is typical Chinese, which is not very good. Whenever this one I have shoots craps, I am ordering from kitsforhams.com.
t |
|
Re: Can not change frequency or CTSS code
Hi Mike,
I can not find any record in our database of you purchasing a genuine SHARI PiXX from Kits for Hams ().? If this is incorrect, please let us know by sending an email to kitsforhams@....? So, since you said it is new, I am guessing that you have purchased the Chinese knock-off clone of our SHARI - probably from Amazon.? This Chinese seller not only tried to copy our hardware design, they call it SHARI and are directing purchasers to us for documentation and support!? Pretty bold!? I will say that this programming problem is unique to the Chinese clone as your input looks correct and any version of SA818-prog will program a genuine SHARI for valid frequencies in the 2 meter or 70 cm ham bands.. After testing this Chinese clone about a year ago (when the SA818-prog program did work), I? posted? (see message 2661), about the problems with this Chinese clone rip-off of our SHARI including the fact that the one I tested does not comply with the spurious emissions requirements of the Part 97 rules and regulations for ham radio and can be programmed outside the allocated ham bands but does not have FCC authorization for use on these frequencies - both of which made it illegal for sale in the US. As I have stated before in previous messages on this group, we do not intend to support this Chinese clone.? We have a database of all of our SHARI purchasers and if we cannot verify you are a SHARI owner by looking at our list, we will contact you for verification.? I also ask that you spread the word about the support issues and technical problems with this Chinese clone.?? To all of our genuine SHARI purchasers, thank you for your support.. Steve - N8AR |
|
Can not change frequency or CTSS code
New to this group and to Allstar
I purchased a Rasberry Pi2 and a Shari PiHat UHF,? NOT a kit and went by the directions multiple times and keep getting the following error (see Picture) Everything works on the default frequency and CTSS code but the default is out of band. I made connections and can hear other nodes so everything is working. I am thinking I must of skipped something in setup but just can figure it out. Any suggest would be gratefully appreciated. Thanks Mike, N2GMU?? |
|
Re: Information were incorrect
#Allstar_Setup
I am having same problem I just posted something before i saw this post.?
Mine works out of band i mean 450.050 with a CTSS of 67.0 this is was the default in the Shari I get the ame error as you when i try to change. See picture |
|
Re: Information were incorrect
#Allstar_Setup
I tried to look up which version of SHARI you purchased from us but could not find your email address you used to join the group?in our database.? What is your call and Is this a SHARI PiXX or a SHAR PiHat?
|
|
Re: Information were incorrect
#Allstar_Setup
We need Steve N8AR to step in. I believe he has set up the frequency setting program... so that out of band (may be this is SAT sub band) cannot be programmed.
Try 440.44000 ? That's what I use and it works.. I vaguely recall something about not being able to program every frequency the SA-818 allows.. Are you sure yours is UHF???? Just covering bases... Larry W8LM |
|
Information were incorrect
#Allstar_Setup
I'm doing something wrong and I don't know what it is. I will appreciate help. Happy New Year.
|
|
Re: Node Connected Announcement
¿ªÔÆÌåÓýConnect.sh /Disconnect.sh will handle Allstar/echolink/IRLP and Extensions connect and disconnect announcements. if thru Hamshackhotline or HamsOverIP then you need to edit your extensions.conf file to remove lines that announce your node number.On 12/26/2022 1:18 PM, WD5M David M.
wrote:
|
|
Re: Node Connected Announcement
On Wed, Dec 21, 2022 at 12:49 PM KB9WOO <kb9woo@...> wrote: I swore I saw this when I first installed Allstar (HamVoip).? I want to disable the announcement of my local node number when a connection is established.? Currently the announcement states "node xxxx connected to node xxxx".? I'd rather it only announce the remote node number is connected and leave out the local node number.? Am I imagining seeing this? This annconnect.sh script for connpgm/discpgm in rpt.conf might provide this capability. It can also be called from Supermon smlogger.? See <>. David McAnally WD5M |
|
Locked
Re: SHARI PiHatU ... Red & Yellow led's not working - Solved
Larry,
I've never seen anyone use a Pi for Bitcoin. It's way too underpowered.? I'm frustrated by the supply shortages too, but that's not the issue.?? Your point about being for youth/students/schools is valid.? Which would make it not meant for us as well right? Let's just stay positive and focus on what we control.?? Mike |
AD?BY
Steve-N8AR
Larry Macionski
Brad N8PC
David McAnally, WD5M
Mike Webb [WG5EEK]