Re: Shari node not receiving my HT
It was the carrier (item I) in simple USB configurations menu. I
am too scared to fiddle any more and perhaps breaking what isn't
broken...
73 (Kind regards),
Hendrik (ZS6HBS)
Please visit my QRZ page at
On 7/12/2024 3:48 PM, N8AR via
groups.io wrote:
toggle quoted message
Show quoted text
SHARI PiXX working with "usb" instead of "usbinvert" for COSFROM
is very strange.? Are you referring to CTCSSFROM instead of
COSFROM.? Have you looked at simpleusb.conf to see if it set to
"usb" there???
|
Re: AllStarLink.org - New ASL3 version just released - HUGE upgrade for all Pi & PC versions
toggle quoted message
Show quoted text
On Sun, Jul 14, 2024, 3:33 PM Brad Kellison N8PC < bradn8pc@...> wrote: Follow the directions on the site. It should have the install docs on them
On Sun, Jul 14, 2024, 10:50 AM Richard Anderson via <koolray_67= [email protected]> wrote: Just tried to do upgrade and I don't have "apt" or "dpkg"
Any help?
|
Re: AllStarLink.org - New ASL3 version just released - HUGE upgrade for all Pi & PC versions
Tried ASL3 and Allmon3, couldn't get it to work properly. Couldn't send dtmf tones and it would only let my node connect to another node once and once only. Tried with several nodes, same thing. At least Hamvoip worked right off the bat.
|
Re: AllStarLink.org - New ASL3 version just released - HUGE upgrade for all Pi & PC versions
|
Re: AllStarLink.org - New ASL3 version just released - HUGE upgrade for all Pi & PC versions
Follow the directions on the site. It should have the install docs on them
On Sun, Jul 14, 2024, 10:50 AM Richard Anderson via <koolray_67= [email protected]> wrote: Just tried to do upgrade and I don't have "apt" or "dpkg"
Any help?
|
Re: AllStarLink.org - New ASL3 version just released - HUGE upgrade for all Pi & PC versions
AllStarLink.org......where else ? Where it says in big green letters "Download for PC/Raspberry PI"
|
Re: AllStarLink.org - New ASL3 version just released - HUGE upgrade for all Pi & PC versions
where is the IMG file to download?
|
I was looking for the bash command to get the setup for audio tuning, I found it in a PDF I had lost. (Part of the reason for asking)
But I found it.. Thanks.
|
What photo are you referring to?
|
Re: ASL3 DTMF not recognized
I used your settings and updated ASL3 and all is working! Thanks so much.
Joe AF1E
|
What is the command to the second photo?
|
Re: AllStarLink.org - New ASL3 version just released - HUGE upgrade for all Pi & PC versions
Michael, That was what I did on both of my PiHAT U and V. COS LED lit up when I keyed up the node. [events] ;;;;; Events Management ;;;;; ;status,2 = c|f|RPT_NUMLINKS ? ? ? ? ? ? ? ; Say time of day when all links disconnect. cop,62,GPIO4:1 = c|t|RPT_RXKEYED cop,62,GPIO4:0 = c|f|RPT_RXKEYED
?
|
Re: Beep after transmission
I changed mine to linkunkeyct = ct3
Now I have a low pitch tone that no longer rips my ears.
You get the original tone if you kerchunk and you're not connected.
On 2024-07-12 11:39, Patrick Perdue
wrote:
toggle quoted message
Show quoted text
There are? a few ways, depending on how granular you want to
make it.
On my simplex nodes, I like to disable the courtesy tone of
link received transmissions, but still have the one that plays
for incoming local transmissions, so I know I'm keying the node.
To disable all telemetry, including courtesy tones (other than
ID) as well as disabling all hangtimes, in rpt.conf, change
duplex=1
to
duplex=0.
To just disable the courtesy tone you hear when a network
transmission ends, look for the definition in rpt.conf for
linkunkeyct.
By default, this is
linkunkeyct = ct8
and comment out that line.
hth
N2DYI
On 7/12/2024 6:55 AM, Sander [VK6PI]
via groups.io wrote:
Hi,
how can I disable the beep after every transmission from
the Allstar node (ShariPi)? "Roger beep" is that how it's
called?
Cheers,
Sander - VK6PI
|
Re: Shari node not receiving my HT
Glad to hear that your node is working now. Now, my node is broken, and it’s not detecting any transmit audio from my Yaesu FT-5D. I think I’ll have to start again with a new image and configure it to my screenshots of a working node.
Dave KY0L
On Fri, Jul 12, 2024 at 8:35?AM Hendrik Steyn via <groothendrik.steyn= [email protected]> wrote:
Thanks for all the help. I found the culprit! I changed the
USBInvert option to plane USB and now it's working -- even the
DTMF tones.
73 (Kind regards),
Hendrik (ZS6HBS)
Please visit my QRZ page at
On 7/11/2024 8:00 PM, Dave via
wrote:
I have a Shari PiHat-4U, and it is working with
ASL3.?
Here are my configuration parameters:
asl-menu:
8. Interface Tune CLI:
sa818-menu:
There
are new updates for ASL3 available.? Please apply them.
Here are the settings for the SA818 and simpleusb that I am
using for ASL3.? Please try them.
|
Re: Beep after transmission
There are? a few ways, depending on how granular you want to make
it.
On my simplex nodes, I like to disable the courtesy tone of link
received transmissions, but still have the one that plays for
incoming local transmissions, so I know I'm keying the node.
To disable all telemetry, including courtesy tones (other than
ID) as well as disabling all hangtimes, in rpt.conf, change
duplex=1
to
duplex=0.
To just disable the courtesy tone you hear when a network
transmission ends, look for the definition in rpt.conf for
linkunkeyct.
By default, this is
linkunkeyct = ct8
and comment out that line.
hth
N2DYI
On 7/12/2024 6:55 AM, Sander [VK6PI]
via groups.io wrote:
toggle quoted message
Show quoted text
Hi,
how can I disable the beep after every transmission from
the Allstar node (ShariPi)? "Roger beep" is that how it's
called?
Cheers,
Sander - VK6PI
|
Re: Shari node not receiving my HT
SHARI PiXX working with "usb" instead of "usbinvert" for COSFROM is very strange.? Are you referring to CTCSSFROM instead of COSFROM.? Have you looked at simpleusb.conf to see if it set to "usb" there???
|
Re: Shari node not receiving my HT
Thanks for all the help. I found the culprit! I changed the
USBInvert option to plane USB and now it's working -- even the
DTMF tones.
73 (Kind regards),
Hendrik (ZS6HBS)
Please visit my QRZ page at
On 7/11/2024 8:00 PM, Dave via
groups.io wrote:
toggle quoted message
Show quoted text
I have a Shari PiHat-4U, and it is working with
ASL3.?
Here are my configuration parameters:
asl-menu:
8. Interface Tune CLI:
sa818-menu:
There
are new updates for ASL3 available.? Please apply them.
Here are the settings for the SA818 and simpleusb that I am
using for ASL3.? Please try them.
|
Hi,
how can I disable the beep after every transmission from the Allstar node (ShariPi)? "Roger beep" is that how it's called?
Cheers, Sander - VK6PI
|
Re: Shari node not receiving my HT
I have a Shari PiHat-4U, and it is working with ASL3.?
Here are my configuration parameters:
asl-menu:
8. Interface Tune CLI:
sa818-menu:
There are new updates for ASL3 available.? Please apply them.
Here are the settings for the SA818 and simpleusb that I am using for ASL3.? Please try them.
|
Re: Shari node not receiving my HT
There are new updates for ASL3 available.? Please apply them.
Here are the settings for the SA818 and simpleusb that I am using for ASL3.? Please try them.
|
Hendrik Steyn
Brad N8PC
Steve-N8AR
Richard Anderson
Joe Spears AF1E
Scott, KB3JQQ
