Re: Trouble connecting to ALS3 node
I used the repeaterbook app and checked the frequency I wanted to
use
and 5 MHz up and down within 25 miles of my site. All good here.
On 2024-11-26 09:39, Jon Spreha via
groups.io wrote:
toggle quoted message
Show quoted text
?
> It's worth mentioning that 446.1 mHz is indeed an
active repeater input in some places.
?
As a new ham, myself.... other than listening to your ALSN
frequency with no PL tone and checking repeaterbook in your
area, is there any other thing we should do to stay out of the
"hardway" column ?
?
I did notice when I setup my hotspot sans a PL tone that I
was getting some stray signals into my node, not full
conversations just some noise.? I tossed a PL tone on it and I
have yet to hear any noise.? ? ?This just reminded me to remove
the RX tone on my HT to make sure I am not hearing anything.?
Jon N7JMS
|
Re: Trouble connecting to ALS3 node
?
> It's worth mentioning that 446.1 mHz is indeed an active repeater input in some places.
?
As a new ham, myself.... other than listening to your ALSN frequency with no PL tone and checking repeaterbook in your area, is there any other thing we should do to stay out of the "hardway" column ?
?
I did notice when I setup my hotspot sans a PL tone that I was getting some stray signals into my node, not full conversations just some noise.? I tossed a PL tone on it and I have yet to hear any noise.? ? ?This just reminded me to remove the RX tone on my HT to make sure I am not hearing anything.?
Jon N7JMS
|
Re: Trouble connecting to ALS3 node
It's worth mentioning that 446.1 mHz is indeed an active repeater
input in some places.
Someone in Brooklyn who had a SHARI and didn't change it's
frequency found that out the hard way once.
On 11/25/2024 12:40 AM, N8AR via
groups.io wrote:
toggle quoted message
Show quoted text
My Yaesu DR-1X automatically shifts the TX frequency by 600
kHz at 446.100 MHz until I change it.? Check and make sure yours
is set to simplex.? ?CONFIG>RPT SHIFT>SIMPLEX
|
Re: Trouble connecting to ALS3 node
Well, that did the trick? Thanks for troubleshooting, greatly appreciated!?
73
My Yaesu DR-1X automatically shifts the TX frequency by 600 kHz at 446.100 MHz until I change it.? Check and make sure yours is set to simplex.? ?CONFIG>RPT SHIFT>SIMPLEX
|
Re: Trouble connecting to ALS3 node
My Yaesu DR-1X automatically shifts the TX frequency by 600 kHz at 446.100 MHz until I change it.? Check and make sure yours is set to simplex.? ?CONFIG>RPT SHIFT>SIMPLEX
|
|
|
Re: Trouble connecting to ALS3 node
In simpleusb menu Item V do COS and PTT change when you key your HT?
|
Re: Trouble connecting to ALS3 node
Yaesu HT w/ CTCSS - Tone enabled Duplex type - 1 half duplex hotspot
thanks
The settings look fine.
?
Are you sure you have CTTS enabled on your HT?
?
What mode did you select in ASL3 setup?? It needs to be duplex=1 in rpt.conf
|
Re: Trouble connecting to ALS3 node
The settings look fine.
?
Are you sure you have CTTS enabled on your HT?
?
What mode did you select in ASL3 setup?? It needs to be duplex=1 in rpt.conf
|
Trouble connecting to ALS3 node
?I am unable to connect to SHARI (Pi4)ALS3 node with HT.? Brand new (device), install of ALS3, on new sd card.? I can receive from the node to HT.? My settings are listed below.......
Thanks 73
?
|
This works! I've used it myself on hamvoip image
toggle quoted message
Show quoted text
I like small displays on pi-star hotspots (0.96") so I can confirm it's on, running normally, internet connected, and what the ip address is. This is most important on a hotspot I may move between locations. Ken, N2VIP ?
Such a display could essentially show the same info that is available in Supermon, Allmon, or lsnode. If it were a nextion it would be possible to also enable simple commands like link and unlink. ?
I have such an interface on my mmdvm hotspot, it’s not that useful. Mostly a novelty.? I only use it to power cycle the node.?
Honestly if you’re somewhere where you can stare at your node, you can just have a cheap tablet or old smartphone with a browser available to just access Supermon/Allmon/Allscan/etc.?
/jim N6KRJ?
---- On Fri, 22 Nov 2024 20:10:15 -0800 Ken N2VIP< ken@...> wrote ----
Dennis,
It's not my idea, I just fleshed out what Jeff mentioned.
There is no 'contact info' to share, since there are no DMR IDs nor a database to query, so all it could really display is SHARI status info.
This does not, to the best of my knowledge, exist - I'm just discussing possibilities. Ken, N2VIP ? Ken,
?
I would like to see that! Would it be on a 3.5 inch display? It sounds like it would look similar to the Zumspot Elite.
?
73’蝉
--
Dennis - KD9ULM
|
?
Ken,
?
I’m in agreement with you on your points you mentioned. It doesn’t need to be flashy, just something simple with information that you mentioned.
Dennis - KD9ULM
|
I like small displays on pi-star hotspots (0.96") so I can confirm it's on, running normally, internet connected, and what the ip address is. This is most important on a hotspot I may move between locations.
toggle quoted message
Show quoted text
On Nov 23, 2024, at 10:37, Jim N6KRJ via groups.io <n6krj@...> wrote:
?
Such a display could essentially show the same info that is available in Supermon, Allmon, or lsnode. If it were a nextion it would be possible to also enable simple commands like link and unlink. ?
I have such an interface on my mmdvm hotspot, it’s not that useful. Mostly a novelty. ?I only use it to power cycle the node.?
Honestly if you’re somewhere where you can stare at your node, you can just have a cheap tablet or old smartphone with a browser available to just access Supermon/Allmon/Allscan/etc.?
/jim N6KRJ?
Dennis,
It's not my idea, I just fleshed out what Jeff mentioned.
There is no 'contact info' to share, since there are no DMR IDs nor a database to query, so all it could really display is SHARI status info.
This does not, to the best of my knowledge, exist - I'm just discussing possibilities. Ken, N2VIP ? Ken,
?
I would like to see that! Would it be on a 3.5 inch display? It sounds like it would look similar to the Zumspot Elite.
?
73’蝉
--
Dennis - KD9ULM
|
Such a display could essentially show the same info that is available in Supermon, Allmon, or lsnode. If it were a nextion it would be possible to also enable simple commands like link and unlink. ?
I have such an interface on my mmdvm hotspot, it’s not that useful. Mostly a novelty. ?I only use it to power cycle the node.?
Honestly if you’re somewhere where you can stare at your node, you can just have a cheap tablet or old smartphone with a browser available to just access Supermon/Allmon/Allscan/etc.?
/jim N6KRJ?
toggle quoted message
Show quoted text
Dennis,
It's not my idea, I just fleshed out what Jeff mentioned.
There is no 'contact info' to share, since there are no DMR IDs nor a database to query, so all it could really display is SHARI status info.
This does not, to the best of my knowledge, exist - I'm just discussing possibilities. Ken, N2VIP ? Ken,
?
I would like to see that! Would it be on a 3.5 inch display? It sounds like it would look similar to the Zumspot Elite.
?
73’蝉
--
Dennis - KD9ULM
|
|
|
Scott, KB3JQQ
Steve-N8AR
Dennis
Jim N6KRJ
Martin OE9SAU