Re: AllStarLink.org - New ASL3 version just released - HUGE upgrade for all Pi & PC versions
AllStarLink.org......where else ? Where it says in big green letters "Download for PC/Raspberry PI"
|
Re: AllStarLink.org - New ASL3 version just released - HUGE upgrade for all Pi & PC versions
where is the IMG file to download?
|
I was looking for the bash command to get the setup for audio tuning, I found it in a PDF I had lost. (Part of the reason for asking)
But I found it.. Thanks.
|
What photo are you referring to?
|
Re: ASL3 DTMF not recognized
I used your settings and updated ASL3 and all is working! Thanks so much.
Joe AF1E
|
What is the command to the second photo?
|
Re: AllStarLink.org - New ASL3 version just released - HUGE upgrade for all Pi & PC versions
Michael, That was what I did on both of my PiHAT U and V. COS LED lit up when I keyed up the node. [events] ;;;;; Events Management ;;;;; ;status,2 = c|f|RPT_NUMLINKS ? ? ? ? ? ? ? ; Say time of day when all links disconnect. cop,62,GPIO4:1 = c|t|RPT_RXKEYED cop,62,GPIO4:0 = c|f|RPT_RXKEYED
?
|
Re: Beep after transmission
I changed mine to linkunkeyct = ct3
Now I have a low pitch tone that no longer rips my ears.
You get the original tone if you kerchunk and you're not connected.
On 2024-07-12 11:39, Patrick Perdue
wrote:
toggle quoted message
Show quoted text
There are? a few ways, depending on how granular you want to
make it.
On my simplex nodes, I like to disable the courtesy tone of
link received transmissions, but still have the one that plays
for incoming local transmissions, so I know I'm keying the node.
To disable all telemetry, including courtesy tones (other than
ID) as well as disabling all hangtimes, in rpt.conf, change
duplex=1
to
duplex=0.
To just disable the courtesy tone you hear when a network
transmission ends, look for the definition in rpt.conf for
linkunkeyct.
By default, this is
linkunkeyct = ct8
and comment out that line.
hth
N2DYI
On 7/12/2024 6:55 AM, Sander [VK6PI]
via groups.io wrote:
Hi,
how can I disable the beep after every transmission from
the Allstar node (ShariPi)? "Roger beep" is that how it's
called?
Cheers,
Sander - VK6PI
|
Re: Shari node not receiving my HT
Glad to hear that your node is working now. Now, my node is broken, and it¡¯s not detecting any transmit audio from my Yaesu FT-5D. I think I¡¯ll have to start again with a new image and configure it to my screenshots of a working node.
Dave KY0L
On Fri, Jul 12, 2024 at 8:35?AM Hendrik Steyn via <groothendrik.steyn= [email protected]> wrote:
Thanks for all the help. I found the culprit! I changed the
USBInvert option to plane USB and now it's working -- even the
DTMF tones.
73 (Kind regards),
Hendrik (ZS6HBS)
Please visit my QRZ page at
On 7/11/2024 8:00 PM, Dave via
wrote:
I have a Shari PiHat-4U, and it is working with
ASL3.?
Here are my configuration parameters:
asl-menu:
8. Interface Tune CLI:
sa818-menu:
There
are new updates for ASL3 available.? Please apply them.
Here are the settings for the SA818 and simpleusb that I am
using for ASL3.? Please try them.
|
Re: Beep after transmission
There are? a few ways, depending on how granular you want to make
it.
On my simplex nodes, I like to disable the courtesy tone of link
received transmissions, but still have the one that plays for
incoming local transmissions, so I know I'm keying the node.
To disable all telemetry, including courtesy tones (other than
ID) as well as disabling all hangtimes, in rpt.conf, change
duplex=1
to
duplex=0.
To just disable the courtesy tone you hear when a network
transmission ends, look for the definition in rpt.conf for
linkunkeyct.
By default, this is
linkunkeyct = ct8
and comment out that line.
hth
N2DYI
On 7/12/2024 6:55 AM, Sander [VK6PI]
via groups.io wrote:
toggle quoted message
Show quoted text
Hi,
how can I disable the beep after every transmission from
the Allstar node (ShariPi)? "Roger beep" is that how it's
called?
Cheers,
Sander - VK6PI
|
Re: Shari node not receiving my HT
SHARI PiXX working with "usb" instead of "usbinvert" for COSFROM is very strange.? Are you referring to CTCSSFROM instead of COSFROM.? Have you looked at simpleusb.conf to see if it set to "usb" there???
|
Re: Shari node not receiving my HT
Thanks for all the help. I found the culprit! I changed the
USBInvert option to plane USB and now it's working -- even the
DTMF tones.
73 (Kind regards),
Hendrik (ZS6HBS)
Please visit my QRZ page at
On 7/11/2024 8:00 PM, Dave via
groups.io wrote:
toggle quoted message
Show quoted text
I have a Shari PiHat-4U, and it is working with
ASL3.?
Here are my configuration parameters:
asl-menu:
8. Interface Tune CLI:
sa818-menu:
There
are new updates for ASL3 available.? Please apply them.
Here are the settings for the SA818 and simpleusb that I am
using for ASL3.? Please try them.
|
Hi,
how can I disable the beep after every transmission from the Allstar node (ShariPi)? "Roger beep" is that how it's called?
Cheers, Sander - VK6PI
|
Re: Shari node not receiving my HT
I have a Shari PiHat-4U, and it is working with ASL3.?
Here are my configuration parameters:
asl-menu:
8. Interface Tune CLI:
sa818-menu:
There are new updates for ASL3 available.? Please apply them.
Here are the settings for the SA818 and simpleusb that I am using for ASL3.? Please try them.
|
Re: Shari node not receiving my HT
There are new updates for ASL3 available.? Please apply them.
Here are the settings for the SA818 and simpleusb that I am using for ASL3.? Please try them.
|
Re: ASL3 DTMF not recognized
There are new updates for ASL3 available.? Be sure to apply them.
|
Re: ASL3 DTMF not recognized
You need to enable pre-emphasis/deemphasis.? You can do this in the SA818 or in simple USB.? You also need the PLfilter(simpleusb) or thehigh pass filter (SA818) enabled to filter out the CTCSS tone.
I prefer to do the filtering in the SA818.? Here are the settings I am using:
|
Re: ASL3 DTMF not recognized
Thanks for all of the help so far.? Here are my settings.? Let me know if you need more. Joe Speed is default 
|
Shari node not receiving my HT
Good afternoon,
On Monday I received my Shari USB radio that I use on a Pi4B. It
works well in Hamvoip, but not in ASL V3.
I got all kinds of errors while programming it via the
sa818-menu, untill I changed it to /dev/tty0USB. Now I can hear
Allison talking. When keying up, however, there is nothing
happening. I checked asterisk -rv, but nothing is coming in. All
the settings on the HT (RT3S) I'm using, is correct, because it
works in Hamvoip. ASL V3 also works with Repeater Phone on iOS.
Any ideas?
Below are some screenshots of simple USB and sa818-menu.
--
73 (Kind regards),
Hendrik (ZS6HBS)
Please visit my QRZ page at
|
Re: ASL3 DTMF not recognized
Please post screen clips of your simpleUSB and SA818 settings?
|
Richard Anderson
Steve-N8AR
Joe Spears AF1E
Scott, KB3JQQ
Hendrik Steyn
