开云体育

Under general settings add a dash# to your dmr id -1 -10 On each different one Mark Hogan N5OBC

Hello all. I have two hotspots running right now. One for TGIF (set to my talk group) and the second is for Dstar. I want to run a hotspot at work and have it be able to connect to TGIF 31665 and also

Check out this thread https://forums.raspberrypi.com//viewtopic.php?p=1337231&sid=8c457573352d107dbd1590a37d8b8e6a#p1337231 Get BlueMail for Android <https://bluemail.me>

I use the "Overlay Root File System" option on my pi setups where I'm not doing graceful shutdowns. Following install/configuration of an image use "overlayfs" to preserve it, activated via "sudo

N5XMT wrote: Well, it *may* corrupt the SD card.? And then, it *may* not get automatically repaired during the boot process.? May-squared can be a really small number, depending on what's going on

Switching off power without a proper shutdown first will corrupt the SD card. ?Get BlueMail for Android ?

I use these HS-105 TP-Link?Kasa Smart WiFi Plug/outlet. They have worked quite well over the years! There is a Kasa app that goes on the Iphone or Android and you control the HS-105 with the

https://www.amazon.com/Female-Switch-YOUCHENG-Raspberry-2-Pack/dp/B08CKKQZ7V/ref=sr_1_5 USB-C https://www.amazon.com/LoveRPi-MicroUSB-Switch-Raspberry-Female/dp/B018BFWLRU/ref=pd_bxgy_sccl_2/146-9662

Check out this thread https://forums.raspberrypi.com//viewtopic.php?p=1337231&sid=8c457573352d107dbd1590a37d8b8e6a#p1337231 ?Get BlueMail for Android ?

Hello all. I have two Pi's running DMR and Dstar respectively so, I have MMDVM hats on both. I need a power button to turn ON and OFF the Pi's. Does anyone have a workable solution to this issue?

That worked, thank you so much! I’m back online!!!

Aaron, I have a Pi 4 with 8 GB of RAM running Hamclock (or just HC) about 20" from my elbow. It runs great. I've dedicated my Pi to that only. I can tell you I've run HC on my Pi 3 with 2 GB of RAM

Like previously mentioned I’m running the weewx-aprx extension and in the weewx.conf I added a binding to the archive instead of the loop. Pasted my conf below. [WeewxAprx] lat = 4638.04N

Lorin Tremblay via groups.io wrote: Confirmed; I see nice smooth data now being reported on aprs.fi. Question:? Where is this setting, and what is "it" that was changed? Greg? KO6TH

Problem solved , changed it from loop to archive and everything is there But i’m using the aprx extension, not the wxcn or xastir

It's wireless. I did have a problem with the way humidity was reported when I first started using the wxcn extension with weewx. wxcn provided three places for humidity whilst the aprs spec only

Is you vp2 wired or wireless, mine is wireless and the data is being captured by sdr over the ait.

http://www.gestionlgt.com/Chalet/ For me personally i modding aprx.py for mytest

Good question, Lorin. What does your data look like when viewed on your local system (via the web page)? If it's the same as what is seen on aprs.fi, then the issue must be upstream with the

My understanding is that all weewx reports use database (weewx.sdb) data, some of which is calculated and some is directly from the instrument values. Does this info on the weewx Acurite driver