开云体育

I think what he means by "bloat" is that there are a lot of non-essential packages installed by default on Raspian, especially when installing new software via apt-get. I know of several other

Good morning. I?ve looked up and down that page and cant see a download link. Aparently, F6BVP is working on an update that should?ve been out mid- April. Paulo, CT2IWW

I am using F6BVP's distribution of Raspbian/FPAC/FBB. It's great. Packet Radio BBS, FPAC NetRom Node RaspBerry Pi setup howto http://f6bvp.org/AX25_BBS_Node_RaspBerry_Pi_install.html Packet Radio

I had no intention of putting in KISS mode...Did it once...Had to do a hard reset to get it out of KISS mode. I intend to use it in COMMAND mode or as a digipeater.

Be careful using that KPC+ in Kiss mode as?they are?known for causing delayed packets. They work fine in command mode as a standalone digi.. Max KG4PID ________________________________ To:

I originally bought it and a Kantronics KPC3+ so I can do Packet radio and not have to lug around my laptop. This is primarily for races that we support on an island. What is a good software to

Thanks all again, I am working on a number of Raspberry Pi projects and Arduino projects with a few very old PICAXE projects finished in the side awaiting pretty cases. My C programming is slow as I

Looking back into previous topics in the group I didn't not see much about different distrobutions. I currently have my Pi/TNC loaded with raspbian, but like others have mentioned its quite bloated. I

Sorry, I didn't make very good notes as this is all I have. 1. Install the standard Raspbian motion package via apt-get. 2. Unzip the motion-mmal tarball into your home folder. 3. Then try running

From what I have seen when I did a look up for motion-MMAL, moiton-MMAL is the actual motion program but is a 'special' build by the Pi community to support the Pi camera module. Here's a link that

I am using one of this for my RPi/TNC-Pi combo. It will need some modification but nothing a Dremel tool and cutting wheel can’t handle. Bruce, KQ4TV

Thanks to everyone who send info for motion-mmal, I have at least a dozen bookmarks now. One question: do I install motion first followed by motion-mmal per the info provided here ? Since

Here's one that apparently has room for the TNC-PI. http://www.amazon.com/gp/product/B00B88ANKU/ref=oh_details_o08_s00_i00 Unfortunately most of these cases are plastic and not a nice

Check out the 'Howto' at the RPi site http://www.raspberrypi.org/learning/webcam-timelapse-setup/ http://www.raspberrypi.org/learning/webcam-timelapse-setup/ Paul 5B8BA

I've seen designs for RPi cases made from Lego - a couple more layers of bricks should do the job. Paul 5B8BA

Take a look at Bud's "Pi Sandwich". It's great for this application. They are available in lots of different places, but here's a link to it

I would love to see varieties on this theme. W4RFQ and I (ka2dew) are working on a housing that will hold the Raspberry PI plus 3 TNC-PI and a 12v power-pole input supply for the stack with backup

Yep. That was a good segment for Peter. I have watched ALTV since the start. Ham Nation and Ham Radio Now are great too. Anyone want to do a Podcast? RadioPi comes to mind as a name. On

Does anyone make a case tall enough to hold a RasPi and the TNC-Pi? All the ones I've seen are too short. Max KG4PID

If this helps out, here's a book that I found interesting about doing just that: Raspberry Pi for Secret Agents Here's the pdf download that I found after I had checked it out at the