开云体育

Yes. MMDVMHost (and DOH) use a floating point value from 0.0 to 100.0, which they then convert into an unsigned character with a range from 0 to 255 that the modem firmware expects. The QnetGateway

Thank you Tom. I may not be able to try this until next week. I think the default value I've seen in DOH and Pi-Star was 100. I thought the valid range was 1-100. But I could easily be mistaken. I

To talk to YSFGateway, local port should be 3200, and gateway port should be 4200.? Local port refers not to the device, but to MMDVMHost itself.? Even though they run together, MMDVMHost and

*RF Level* is now available in the "./qnconfig expert" menu. The default value is 255 (100%) and the range is 0 to 255. I have no idea how linear this parameter is for any given modem. Of course this

We’re talking about the local port under the fusion heading that should be 4200 correct? i’m looking at my fusion network heading, and I see: [System Fusion

GOtcha… sorry about that.

Sorry that I wasn't clear.? The Fusion Network port in MMDVM.qn SHOULD be 4200.? This is the port used for communication between MMDVMHost and YSFGateway. The port used for outbound connection from

So I went back, and updated my network port in YSFGateway.qn, and MMDVMhost.qQN to 42000, uninstalled, and then recompiled the program. YSF gateway is running, I can get confirmation from the hotspot

You shouldn't need to open ports to use YSF reflectors.? There is constant polling between YSFGateway and the reflector which keep everything open. From the log, it seems that YSFGateway is

Hi, I’ve been playing with the YSF portion of Qnet gateway, and it definitely connects to any of the YSF reflectors that I use, but I hear no audio. I suspect that I don’t have the necessary

So there is no reason then I shouldn’t have DMR enabled as well. I don’t have a dmr radio, but if dmr is not enabled, will YSF2DMR work?

You don't need to disable one to use the other.? There are to setting near the top of MMDVM.qn that control what is called 'Mode Hang'. 'RFModeHang' is the time in seconds that MMDVMHost will ignore

SO when you want to use the YSF side of the hotspot you just turn off the d-star side, or do you leave it running? I really like the interface now that this is working it is clean, and the dashboard

That happens.? I don't know for sure, but I think it is a temoprary DNS error.? I have waited a bit before trying to connect to one of those listed as 'unable to resolve address' and have been able

SO this looks like that everything started. I”ll have to get some help changing some settings in my FT-70 to make this work, but I do notice that a couple of reflectors could not get loaded: ***

For using YSFGateway, MMDVM.qn should have the following under System Fusion Network: System Fusion Network] Enable=1 LocalAddress=127.0.0.1 LocalPort=3200 GatewayAddress=127.0.0.1 GatewayPort=4200 #

HI there, What does your log path statement look like in MMDVMhost.qn, and YSFGateway.qn? It helps having some examples, since I’m using voiceover on the mac, and having a working example let’s

SO what if I just want to have YSFGateway across the board, what should it look like under MMDVMhost.qn?

Since you are having issues, my first suggestion would be that you configure and verify the functionality of each voice mode independently.? Disable Fusion and Fusion network and verify that D-Star

OK let’s see if this works? I need to have the RX at 439.000, and the TX at 434.000 that’s the way that I have this setup in my Th-d74. I should be able to use MMDVM host?