开云体育

Try sudo su -

rpi-rw

Show me what it says?

On Thu, Sep 13, 2018, 14:21 Nomis Bayan Jr. <nolyn78@...> wrote:

HI Colby,

Yes you are correct, I have not issue the unlink. I just want to make sure it is solid stable link with the reflector.I restarted the Rpi3 several times but no luck.

On Thu, Sep 13, 2018 at 11:11 AM Colby Ross W1BSB <colbypr@...> wrote:

Ok. If you did not issue _______U after you finished using the repeater, it will stay linked to whatever repeater you linked it to.

?

Pi-Star shouldn’t have any problems going into read-write mode. Just restart it. Additionally, you should restart it after you add your repeater to the DPlus_Hosts.txt file as well.

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Thursday, September 13, 2018 14:09
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

HI Colby,

My RPI 3 somehow went bad, I could not get into rpi-rw. I may have to update them when I get home tomorrow. Just to update you on the link, the gateway is till linted to the XRF reflector via dashboard.

?

On Wed, Sep 12, 2018 at 10:36 PM Colby Ross W1BSB <colbypr@...> wrote:

Yes it most go in dplus. Then restart pistar and issue KM6VLBBL and it should link.?

?

Colby?

?

On Thu, Sep 13, 2018, 01:32 Nomis Bayan Jr. <nolyn78@...> wrote:

Hi Colby,

As I recalled, I tried it first on the DPlus_Hosts.txt, then I did on the DExtra. I will try again tomorrow. it is getting late , working out of town, returning to San Diego on Friday. Thank you everyone.

?

On Wed, Sep 12, 2018 at 10:28 PM Colby Ross W1BSB <colbypr@...> wrote:

It should be put into dplus hosts and not dextra. I'm not sure where you added it but it will only accept dplus connections. These occur on port 20001?

?

Colby?

?

On Thu, Sep 13, 2018, 01:23 Nomis Bayan Jr. <nolyn78@...> wrote:

Hi Colby, I have tried that also, but let me try it again. Yes it will say Linking no linked.

?

On Wed, Sep 12, 2018 at 10:03 PM Colby Ross W1BSB <colbypr@...> wrote:

Yes, you have to link to a specific module, in your case which is B, so the proper link command is KM6VLBBL

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Thursday, September 13, 2018 01:02
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

HI Colby,

I was able to add the repeater information to the pi-star host file, but it will say "Linking to KM6VLB L" not "Linked to KM6VLB L", Am I missing some on the gateway configuration?

?

On Tue, Sep 11, 2018 at 8:03 PM Colby Ross W1BSB <colbypr@...> wrote:

Nomis

?

It has been quite some time since I used pi-star, I never used it with D-Star, only for DMR. I know the repeater can be added to the host files, but I’m not quite sure if there is an easy way to do this. You might want to head over to their forum and check it out, they have a pretty good support team.?

?

I just can’t for the life of me remember if they actually had an option that easily added the repeater in the host files or not.

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Tuesday, September 11, 2018 22:33
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

Hi Colby,

I was trying to connect my Zumspot with RPi 3 to the repeater gateway, since it can connect 20 dongles and was not successful. Someone mentioned that I need to update my pi-star to add the repeater information.?

?

On Mon, Sep 10, 2018 at 6:20 PM Colby Ross W1BSB <colbypr@...> wrote:

You can only have one reflector linked to your repeater at a time. However, if the XRF repeater you have linked cross-links their module with another, it would effectively link 2 XRF reflectors with a common module.

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Monday, September 10, 2018 21:19
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

Hi Colby,

Sorry, typo error. Two XRF reflectors. I tried it will not accept.

?

On 9/10/2018 6:17 PM, Colby Ross W1BSB wrote:

You can link your repeater to an XRF reflector, but you already know how to do that. Just issue the standard link command from your radio XRFXXX<Module>L

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Monday, September 10, 2018 21:16
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

Hi Colby,

Can I link to XRF reflector to the repeater?

?

On 9/9/2018 7:26 PM, Nomis Bayan Jr. wrote:

Hi Colby,

Stepped out and did some yard work. Once again, appreciated all the help. Have a great day.

?

On 09/09/2018 04:40 PM, Colby Ross W1BSB wrote:

I was still logged in from before and never logged out, I logged out but forgot what the IP address was so I can’t check it again. I think you are good to go if you removed the port forward though. Because the connection was already established, your firewall would maintain it until it drops even if the port is closed. Your code is up to date with the fixes now though, so you should be good to go.

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 19:37
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

HI Colby,

I removed the SSh, when you told me so and I was not sure if you were able to get into my system, but if you do then please let me know. I will return the ssh.

?

On 09/09/2018 04:00 PM, Colby Ross W1BSB wrote:

Tom discovered an issue with the linking section of QnetGateway and pushed up a fix. I applied that fix to your system as I was still logged in, as well as ensuring the max_dongles was set at 20. I restarted the qngateway and qnlink programs for you so you are on the most up to date code with your desired number of linked dongles.

?

I do not believe there is a timeout option in the sourcode. There isn’t any mention of it in the configuration, so I believe it will stay linked until someone manually unlinks it.

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 18:54
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

Hi Colby,

One of guys was asking me questions;

1. How many hotspot can connect to the gateway? My answer is it is dependend on the settings, I think it was set for 5 and I changed it to 20.

2. If a station use the repeater to kink to another reflector or repeater and forgot to unlink, is there a time duration that the repeater will auto unlink. Not sure what the answer.

?

On 09/09/2018 12:43 PM, Colby Ross W1BSB wrote:

It is, the first system using the ICOM stack of QnetGateway. There are a few others out there running it on hotspots and dongle type devices.? It was my pleasure to help

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 15:42
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

HI Colby,

It was a pleasure to obtain assistance from you. This group is the best group I ever joined. You went an extra miles to help. When I did the XLX server, i reached out to different groups of ham and to other fellow ham and never get a response, but was able to run them after 6 months of not giving up with no linux experience.

You have mentioned that My system was the first real system using the QnetGateway. Thank you for developing this software.

?

On 09/09/2018 12:25 PM, Colby Ross W1BSB wrote:

No problem. Don’t forget to remove the port forward (10022 to port 22) for SSH, that should never be open unless you really need it to be.

?

It was my pleasure to help. You are the first real system that is using QnetGateway outside of our test system we developed it on.

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 15:22
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

HI Colby,

Somehow I have to get use to these commands. Thank you again and the time you have spent to assist me in setting up the gateway and the Icom repeater.

?

On 09/09/2018 12:13 PM, Colby Ross W1BSB wrote:

Well I saw you were trying to talk over the link command.

?

So you issue the XRF072AL command to link, and then switch to Use Reflector CQCQCQ to talk through the reflector.

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 15:12
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

HI Colby,

Hi hot spot stoppped. It was probably on his side. Do you want me to open the ssh so you maybe able to go back when you have the chance, about the smart quad?

?

On 09/09/2018 12:07 PM, Colby Ross W1BSB wrote:

Were you both using the CQCQCQ use reflector? That is the same as for a repeater if you were trying a local QSO to the repeater.

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 15:01
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

Hi Colby,

We were testing and having a qso, but we could not hear each other.

?

On 09/09/2018 10:46 AM, Colby Ross W1BSB wrote:

Norm give me a call at 2073314368

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 13:44
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

Hi Colby, Transmitted more than once at QW1BSB. Did you copy the voice?

?

?

On 09/09/2018 10:37 AM, Colby Ross W1BSB wrote:

I can hear you keying it up, try saying something. Leave it in your UR field at all times

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 13:37
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

I entered the "QW1BSB" on the direct input(UR) and ptt twice. nothing happens.

?

On 09/09/2018 10:27 AM, Colby Ross W1BSB wrote:

Put QW1BSB in the UR field of your radio you’re using to communicate with your ICOM repeater. You may have to key it twice to get it to subscribe, it should come back with a confirmation tone once you have logged in.? I want to make sure the ircDDB routing portion is working as well, then I will try a reflector link with you to make sure.

?

Just put QW1BSB in your UR field, key it once, and then key it again. You should subscribe, and I’ll try to get in contact with you. Just leave QW1BSB in your UR field to talk on it.

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 13:25
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

Hi Colby,

I just connected to the XRF072A reflector and transmit. It is working, thank you so much.Now I need someone transmit and start a qso.

?

?

On 09/09/2018 10:08 AM, Colby Ross W1BSB wrote:

Give me a few minutes. I'm not at my computer. But yes you can safely comment out the IP addresses in the config. The defaults work out of the box. Send me the output of the route command too please.?

?

Colby?

?

On Sun, Sep 9, 2018, 13:02 Nomis Bayan Jr. <nolyn78@...> wrote:

Hi Colby,

Run it again and here is the result. It has stopped. Do you want me to return the # on all the IP on qn.cfg?

root@nolyn78dell:/home/nolyn1978/QnetGateway# systemctl restart qngateway qnlink ; journalctl -u qngateway -f
-- Logs begin at Sun 2018-09-09 09:41:14 PDT. --
Sep 09 09:52:10 nolyn78dell systemd[1]: Started QnetGateway.
Sep 09 09:52:10 nolyn78dell qngateway[1524]: VERSION QnetGateway-7.0.1
Sep 09 09:52:10 nolyn78dell qngateway[1524]: Reading file /usr/local/etc/qn.cfg
Sep 09 09:52:10 nolyn78dell qngateway[1524]: ircddb.login = [KM6VLB]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: OWNER=[KM6VLB]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: ircddb.host = []
Sep 09 09:52:10 nolyn78dell qngateway[1524]: ircddb.port = [9007]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: ircddb.password = [1111111111111]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: module.b.type = [icom]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: module.b.ip = [172.16.0.1]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: module.b.port = [20319]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: module.b.frequency = [448.26]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: module.b.offset = [0]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: module.b.range = [15]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: module.b.agl = [30]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: module.b.latitude = [32]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: module.b.longitude = [127]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: module.b.url = []
Sep 09 09:52:10 nolyn78dell qngateway[1524]: gateway.local_irc_ip = [0.0.0.0]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: gateway.external.ip = [0.0.0.0]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: gateway.external.port = [40000]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: gateway.internal.ip = [172.16.0.20]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: gateway.internal.port = [20000]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: gateway.regen_header = [true]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: gateway.aprs_send = [true]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: gateway.send_qrgs_maps = [true]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: aprs.host = []
Sep 09 09:52:10 nolyn78dell qngateway[1524]: aprs.port = [14580]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: aprs.interval = [40]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: aprs.filter = []
Sep 09 09:52:10 nolyn78dell qngateway[1524]: log.qso = [false]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: log.irc = [false]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: log.dtmf = [false]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: link.outgoing_ip = [127.0.0.1]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: file.echotest = [/tmp]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: file.dtmf = [/tmp]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: file.status = [/usr/local/etc/rptr_status]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: link.port = [18997]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: link.ip = [127.0.0.1]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: timing.play.wait = [1]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: timing.play.delay = [19]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: timing.timeout.echo = [1]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: timing.timeout.voicemail = [1]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: timing.timeout.remote_g2 = [2]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: timing.timeout.local_rptr = [1]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: Repeater callsigns: [KM6VLB-A] [KM6VLB-B] [KM6VLB-C]
Sep 09 09:52:10 nolyn78dell qngateway[1524]: aprs hash code=[17083] for KM6VLB
Sep 09 09:52:10 nolyn78dell qngateway[1524]: startWaiting for irc connection status of 2
Sep 09 09:52:10 nolyn78dell qngateway[1524]: irc status=0
Sep 09 09:52:11 nolyn78dell qngateway[1524]: IRCClient::Entry: connected2
Sep 09 09:52:15 nolyn78dell qngateway[1524]: irc status=0
Sep 09 09:52:17 nolyn78dell qngateway[1524]: IRCDDBApp::setBestServer s-grp1s2
Sep 09 09:52:17 nolyn78dell qngateway[1524]: IRCDDBApp::setCurrentNick km6vlb-1
Sep 09 09:52:20 nolyn78dell qngateway[1524]: irc status=1
Sep 09 09:52:21 nolyn78dell qngateway[1524]: IRCDDBApp: state=2 choose new 's-'-user
Sep 09 09:52:22 nolyn78dell qngateway[1524]: IRCDDBApp: state=3 tableID=1
Sep 09 09:52:24 nolyn78dell qngateway[1524]: IRCDDBApp: state=3 tableID=0
Sep 09 09:52:25 nolyn78dell qngateway[1524]: QnetGateway...entering processing loop
Sep 09 09:52:25 nolyn78dell qngateway[1524]: IRCDDB RPTRQTH: KM6VLB_B +32.00000 +127.00000 La_Mesa,_CA_________ ____________________
Sep 09 09:52:25 nolyn78dell qngateway[1524]: IRCDDB RPTRURL: KM6VLB_B
Sep 09 09:52:25 nolyn78dell qngateway[1524]: IRCDDB RPTRSW: KM6VLB_B QnetGateway-7.0.1
Sep 09 09:52:25 nolyn78dell qngateway[1524]: IRCDDB RPTRQRG: KM6VLB_B 00448.26000 +000.00000 000.01 0030.0
Sep 09 09:52:25 nolyn78dell qngateway[1524]: g2=4, srv=5, MAX+1=6
Sep 09 09:52:25 nolyn78dell qngateway[1524]: APRS beacon thread started
Sep 09 09:52:25 nolyn78dell qngateway[1524]: get_irc_data thread started
Sep 09 09:52:25 nolyn78dell qngateway[1524]: Waiting for ICOM controller...
Sep 09 09:52:25 nolyn78dell qngateway[1524]: Trying to connect to APRS...
Sep 09 09:52:25 nolyn78dell qngateway[1524]: Waiting for up to 15 seconds for APRS_HOST
Sep 09 09:52:26 nolyn78dell qngateway[1524]: Connected to APRS
Sep 09 09:52:27 nolyn78dell qngateway[1524]: IRCDDBApp: state=6 initialization completed
Sep 09 09:53:14 nolyn78dell qngateway[1524]: irc status=7, probable connect...

?

On 09/09/2018 09:49 AM, Colby Ross W1BSB wrote:

You can comment out the IP addresses in qn.cfg, as the defaults just plain work.

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 12:49
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

Hi found the error I just change the IP back to 172.16.0.20, I made an error and entered 172.16.0.1. Let me run again.

?

On 09/09/2018 09:41 AM, Colby Ross W1BSB wrote:

Actually, I think I know what might be wrong. Restart the server, I think more than one instance of qngateway is running causing a bind issue.

?

Reboot the server, and when it comes back up, type journalctl -u qngateway -f and see what it says.

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Colby Ross W1BSB
Sent: Sunday, September 9, 2018 12:38
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

Show me ip a and /etc/network/interfaces again

?

Colby

?

?

From: [email protected] <[email protected]> On Behalf Of Nomis Bayan Jr.
Sent: Sunday, September 9, 2018 12:34
To: [email protected]
Subject: Re: [QnetGateway] Failure on Qngateway Service

?

Hi Colby,

It is working. Except it say "can't open " and "Failed to bind 172.16.0.20". I do not know how to stop the so I could copy the rest.

?

On 09/09/2018 09:00 AM, Colby Ross W1BSB wrote:

Alternatively you can put “ before /tmp and after qnvoice so it reads qnvoicefile = “/tmp/qnvoice.txt”

?

?

?

?

?

?

?

?

?

?

?

?

?

?

?

?

--

Regards,

Nomis A. Bayan Jr.

?

--

Regards,

Nomis A. Bayan Jr.

?

--

Regards,

Nomis A. Bayan Jr.

?

--

Regards,

Nomis A. Bayan Jr.

?

--

Regards,

Nomis A. Bayan Jr.

--

Regards,

Nomis A. Bayan Jr.