开云体育

foam tape to the inside of the cutters trim with a razor blade generally, it will hold the bit you've nipped 73, -bob ah7i

It is neither a high voltage nor high current application. Just about any small Schottky diode should work. <simon.oliver90@...> wrote:

Alan, Yes, the RF module's description is confusing. I couldn't ascertain whether pin 22 (Vbatt) would source current to charge the battery or not. By measuring the battery voltage in my unit (it

Still cant get my QCX to display anything other than blocks. Not even got to the alignment part yet. Might the Diode trick work? I have a spare Schottky Diode but not sure of its specs.

My application was approved on October 25th. I applied on September 20th. Al, N8WQ

place a small bowl at that distance HI (; I usually hold the cutters so that my index finger is on the end of the pin that I'm cutting, this way it just falls off when opening the cutters... the pin,

I have repeated this info from Hans. 73 Ken G4APB Sent: 10 March 2017 09:18 To: [email protected] Subject: Re: [QRPLabs] What is the Jumpter configeration on LPF board NOT to have all ouputs go

I second Pete's suggestion, a full case.?? That would be wonderful!I think many would use it. I am working on the stand now. Paul? K0ZYV To: [email protected] Sent: Friday, October 27, 2017 9:58 AM

What do you mean regarding encoder noise ? Make sure you try Hans solution as well, /g/QRPLabs/message/17414 It makes sense as you have already tried lowering C47 and it has an effect

Nice work! It printed nicely. Now it would be really great if you or someone with design experience could go to the next step and make a full 3D case for the OCX.? Thanks again Phillip.? Pete WK8S

I tried to de-solder L5, but it didn't survive :-( So until I can get a replacement I've linked the top L5 hole (Pin 20 and C36 end) to the Pin 7 end of L6. And now mine starts up first time every

You will never lose any SMD parts using the sticky PEN instead of tweezers... :) http://kitman.eprodavac.cz/adhezivni-smd-pero-stickypen-70/ (

Hans, Just tried schottky from pin 7 to 20 with 470uf tacked on to the 10uf I put there earlier, so 480uf in total at C47, and starts up fine first time. 73 Simon VK3ELH

Hello Hidehiko I do not know why your WSPR spots are different. Others have reported many WSPR reports with the QCX. I think more information would be useful. Are you using a GPS? Have you received

Hi Hans, I would just like to echo the supportive comments Martin (G0PJO) has made. I do hope you will not get disheartened by some of the whingeing comments. We need people with your knowledge and

Mike, OK, I often find myself banging my head on the wall as well! I've added the link to AVRDUDESS so time is not wasted. 73 Alan G4ZFQ

I dont mind bugs. ?Trying to work out whats causing them testing a theory and learning along the way. All part of the fun. Keep up the great work Hans. Lou, what band is your QCX? Mine is on 40m. Be

Eddie, my experience has been the opposite of yours - I find the audio quite loud on my 40m QCX. In fact, I tried using a pair of computer headphones with an inline volume control and had to reduce

Hi Daniel You probably right. My logic is that spikes/pulses can be reduced with low value caps say 0.1uF........... Larger caps say 470uF level out slow changing voltage levels but take a longer time

Hi Alan Sorry for my rantings ~ I have spent more time getting the software update to work than it took to build it. The instructions you wrote are fine (just me not reading) I was trying to run