开云体育

Hi Hans, I have just brought one, not too bad for ?24.00. I have noticed that I will have to put a 3.3v regulator (L78L33) and a couple of caps in line to use the 5v GPS supply on your board. 73

Hi Andy I too would love to get my RaspberryPi setup as a grabber (low energy costs). Since there is no audio in, then it would need a USB sound dongle I presume... No idea about software but fingers

Hi All I have only just joined the group and have built 2 QRSS bacons one for 10.140mhz and 7mhz. Have done nothing but test them so far... My intention is to set-up a grabber on 7Mhz I have several

Hi Steve Many thanks for the info and advice.. will wait till I hear later from you on results. Am anxiously awaiting delivery of the kit. I have had stuff from Maplins in 7 days, stuff my son sends

Thanks Hans... I liked that one because it's easy to add an external antenna... Might take a chance and order one.. Philip G4JVF

Philip, http://www.dpieshop.com/trimble-silvana-acm-with-condor-gps-sma-antenna-connecto&#92; r-p-717.html<http://www.dpieshop.com/trimble-silvana-acm-with-condor-gps-sma-antenna-connector-p-717.html

All, Just to add to what Steve already said about the GPS: 1) When the GPS is enabled (menu configuration), you MUST have the 1pps GPS signal present, because it is used for the timekeeping. When

Tony & all You can also set the time in the last configuration menu item. When you press the left button after setting the minutes digit, the set time (hours and minutes) takes effect and the seconds

Been looking around what's available in GPS modules... I know little about GPS but just hoovering up information.. :) Came across this site which has a good selection and some modules seem a decent

Hi Alan, Thanks for the message and raising the subject of GPSs. Hans and I are doing quite a bit of work with GPS at the moment and hope to recommend some that we know will work with the kit. We

Hi folks Have ordered the kit last week and after reading the online instruction I noted the GPS interface. Question – what type GPS receiver is used. I have a GPS receiver with external antenna

I am conducting some basic stability tests on this kit whilst waiting for the LCD display to arrive. In this minimal boot-up mode the bias on the LED/varicap is about 50% of the supply and there is a

Hi Colin, Welcome to the group and thanks for buying the kit. What mode have you configured the beacon to transmit in? How do you know it is transmitting all the time? Your RX may be picking up the

Hi everyone, My name is Colin and my call signs are DD5CF and G1ZOS I am new to the group and also to digital modes, I have just finished building the ultimate QRSS kit for 30m, is it realy supposed

Has anyone downloaded the new Argo build 141. I really like it. Need some one to explain the grabber upload proceedure as I am somewhat internet challenged. Paul k5wms

All, This is to announce a new QRSS kit by Steve G0XAR and Hans G0UPL. The kit supports WSPR, QRSS, DFCW, FSK/CW, CW, Hell (full speed and half-speed), Slow Hell, and customisable patterns. The WSPR

Hi Giorgo, There is a bug in the code, the main loop is exiting directly. I don't think I can send attachment to the list. Send me a personal e-mail and I will send you the corrected code I used to

Hi QRSS friends, Here an "highly experimental" code for both Arduino (Atmel AVR) or LaunchPad (Texas Instruments MSP430) using Energia (Arduino fork). With this code, a micro-controler and an R-2R

Hi, I am quite new to QRSS and this is my first post here. After few weeks of testing with a W3PM beacon I wanted to build a stand alone 30 meters beacon so after receiving the Hans kit I put is