Re: Ordering parts without outrageous shipping costs
You don't even have to mail in your Digikey order, just the check. You can assemble the cart online and then choose to mail a check to pay. You wait a bit longer for your parts but you save money. On Wed, Dec 13, 2017 at 12:21 PM, D. Daniel McGlothin KB3MUN <kb3mun@...> wrote: On 12/13/2017 11:54, zfreak@... wrote:
I like digikey.com. They stock modern parts, and will ship via USPS...
...and, if you mail a check with the order, they ship free of charge to
US/Canada. See item "6 . Shipping CHarges" under part "II. COnditions of
Order" at .
73 de Daniel KB3MUN
|
Re: Ordering parts without outrageous shipping costs
Thanks Hans.... my only problem my junk box is not that well stocked.... I have new parts on order.
73 Kurt - W2MW
-------- Original Message --------
Subject: Re: [QRPLabs] Ordering parts without outrageous shipping costs
From: "Hans Summers" < hans.summers@...>
Date: Wed, December 13, 2017 1:17 pm
To: [email protected]
This inductor is not at all critical. Just use any inductor from the junk box!?
73 Hans G0UPL
|
hi all
regarding phase noise measurement ,
what is output frequency?
phase noise is not so bad , but spurs are very high depending of frequency (-40/-50db)
to solve it ,i made an injection locking oscillator with +-100khz capture range at aprox 103MHz.
?
another solutions??
73
|
Thanks Hans,
I figured that was the case. Thought I would check before I did much work. FYI here is a phase noise plot on my unit. Don't know much about PN application but I think it looks not bad. Or pretty good based on what my instrument can message. I see the frequency needs some tweaking. SA is GPSDO locked Thanks Dave
On Wed, Dec 13, 2017 at 10:24 AM, Hans Summers <hans.summers@...> wrote: Hi Dave
You have the fuses wrong on the blank chip you programmed.. The default fuse settings for the Tiny84A have the divide-by-8 clock flag enabled. So your ATtiny84A is running 8x too slowly, this explains why you have serial communication at 1200 baud not 9600 baud.?
I think that you should correct the fuse settings - I am not sure if there may be some other undesirable side-effects if the clock is 8 times too slow.?
73 Hans G0UPL
|
Re: Ordering parts without outrageous shipping costs
I see many sellers on eBay (USA) where you get a bunch (stock the parts box) shipped to you for less than $6.
is an example for $4.14 shipped for a pack of 20.
---------
Paul KE7HR
|
Hi Dave
You have the fuses wrong on the blank chip you programmed.. The default fuse settings for the Tiny84A have the divide-by-8 clock flag enabled. So your ATtiny84A is running 8x too slowly, this explains why you have serial communication at 1200 baud not 9600 baud.?
I think that you should correct the fuse settings - I am not sure if there may be some other undesirable side-effects if the clock is 8 times too slow.?
73 Hans G0UPL
On Wed, Dec 13, 2017 at 8:39 PM, Dave Miller <ve7hr@...> wrote: Hans or anyone else,
I am testing out my Progrock with the pr1.01a.hex file.
I cannot connect to it with 9600 Baud but works perfectly on the communication side with 1200 Baud.
Has anyone seen this?
Note I did program the Tiny84 myself from a blank IC.
Are there any setting I need to adjust when programming.
I have not looked at the output yet.
Thansk
Dave
Ve7HR
|
Re: Ordering parts without outrageous shipping costs
This inductor is not at all critical. Just use any inductor from the junk box!?
73 Hans G0UPL
On Wed, Dec 13, 2017 at 8:21 PM, D. Daniel McGlothin KB3MUN <kb3mun@...> wrote:
I
like .
They stock modern parts, and will ship via USPS...
...and, if you mail a check with the order, they ship free of
charge to US/Canada.? See item "6 . Shipping CHarges" under part?
"II. COnditions of Order" at
.
73 de Daniel KB3MUN
|
Re: Output vs. frequency behavior QCX 30m
Try squeezing / pulling out the turns on the yellow filter toroids. This made a? massive difference on my 20m QCX and I was able to go from 2.1W to 3.8W by doing just that.
We'll ignore that fact that it has now stopped TXing - that's another thread!
Steve G0KYA
|
Re: New Year's Eve Operation
Yes, I'll see what I can do.
|
Hans or anyone else,
I am testing out my Progrock with the pr1.01a.hex file.
I cannot connect to it with 9600 Baud but works perfectly on the communication side with 1200 Baud.
Has anyone seen this?
Note I did program the Tiny84 myself from a blank IC.
Are there any setting I need to adjust when programming.
I have not looked at the output yet.
Thansk
Dave
Ve7HR
|
Re: Output vs. frequency behavior QCX 30m
Steve K1RF,
How critical is the resonant circuit C30 and L4 for single band performance? ?Are we looking at a broad bell shaped curve response or a sharp peak? ?I think I read somewhere Hans picked the values by experiment because of the "floating" capacitance from the FETS etc. ?Maybe a mica capacitor would be in order for C30 if the original were heating up.
Bill N7EU
|
Re: Ordering parts without outrageous shipping costs
I
like .
They stock modern parts, and will ship via USPS...
...and, if you mail a check with the order, they ship free of
charge to US/Canada.? See item "6 . Shipping CHarges" under part?
"II. COnditions of Order" at
.
73 de Daniel KB3MUN
|
Re: Ordering parts without outrageous shipping costs
Kurt
while Hans said it was easy to remove L5, my went kaput also (not many days before your attempt) !? it my case it was mechanical stress.?
I found a 25 uH inductor in my stash, made decades ago - a little toroid coil encapsulated with leads.? the higher Q of this inductor seems to not be an issue for this application.? see if you have a ferrite core in your stash, and see how many turns in might take to get into vicinity of 25 uH.? meanwhile - I was also check the firm mentioned as my stash in pretty lean on RF chokes of the smaller variety.?
it was a good result - previously on some power ups the QCX VFO resolution could not be adjusted - as it would go to a different menu item when I pressed the button on the tuning knob - now it seems to be working, based upon just a few trials. ?
Curt
|
Re: Ordering parts without outrageous shipping costs
Kurt,? I like . They stock modern parts, and will ship via USPS. My last order of mostly surface mount parts shipped for less than $4. I can always find stuff to add to my cart to help me justify the four bucks shipping.
I think we're all spoiled by the cheap shipping we can get from Asia. I am still amazed that I can buy something for $0.99 and get it shipped to me, albeit slowly, for free from halfway around the world.? Regards, Mike M. KU4QO
On Wed, Dec 13, 2017 at 11:48 AM, Kurt Zimmerman <kurt@...> wrote: Greetings all;
? Well I was attempting to make the L5 inductor (100 micro Henry across pins 7 & 20)? mod when I apparently overheated it having it to fall apart... one of many boneheaded maneuvers on my part.? Last night I went to several on-line parts places only to find state side shipping costs on items less than $1 can go upwards of $10.? THAT"S CRAZY!? I can see spending $1-$2 which is still high for 5 axial inductors.??
Where do you order your parts from?? Is there a cheaper place I might be missing?
72;
Kurt - W2MW
|
Re: New Year's Eve Operation
Al what is your signal look like with the?5 watt PA out of line. Is it possible to disco it and just run your U3S barefoot. ? I am no expert for sure but I have?never seen a signal such as yours?from a U3S ...besides being ragged looking it wanders considerably up and down in frequency. ? Vernon? ? On 12/13/17 11:23 AM, "Al Holt" <grovekid2@...> wrote:
|
Re: Ordering parts without outrageous shipping costs
TaydaElectronics.com - they have a $5 minimum order requirement, but shipping is very cheap. Just get the bill up to $5, and chances are?that you will pay $1.50 or close to that in shipping. They don't have everything, but it's my go-to place for run of the mill stuff. Shipping might take a little bit longer than your Mouser or Digikey order, but I usually get my package after about a week (give or take a couple of days).?
|
Ordering parts without outrageous shipping costs
Greetings all;
? Well I was attempting to make the L5 inductor (100 micro Henry across pins 7 & 20)? mod when I apparently overheated it having it to fall apart... one of many boneheaded maneuvers on my part.? Last night I went to several on-line parts places only to find state side shipping costs on items less than $1 can go upwards of $10.? THAT"S CRAZY!? I can see spending $1-$2 which is still high for 5 axial inductors.??
Where do you order your parts from?? Is there a cheaper place I might be missing?
72;
Kurt - W2MW
|
Re: Output vs. frequency behavior QCX 30m
If you are trying to operate on both 30/40, the answer is likely that the
output stage, which is a class E amplifier, needs to operate reasonably close to
its optimum resonant frequency.? The series tuned part of the circuit (C30
and L4) can’t be tuned to a “compromise” frequency without degrading one or the
other or both frequencies.? Although broad enough for a single band, it
just won’t work that well if you are away from the resonant frequency because
its efficiency depends on its switching point of the output fets occurring at
near zero current.? As soon as its resonant frequency is moves
significantly away from it’s optimum single band frequency, the three output
fets will experience much higher current at the switching point and end up
dissipating a lot of power, reducing the output power.?
-Steve K1RF
toggle quoted message
Show quoted text
Sent: Wednesday, December 13, 2017 9:03 AM
Subject: Re: [QRPLabs] Output vs. frequency behavior QCX
30m
?
73
Enno,
I too find the same as you. I don't know the answer. It sure works
on both 30/40, which also is unexpected, after all I was trying to make mine
work on 20/30 !
I would like to have higher power output but have not
found the way to do it but I've not been trying very hard. I console myself that
the difference is only maybe 1dB. A doubling of the power would only be 3dB. I'm
pleased though that it works even better on 40m, which was
surprising.
However the little extra power on 40m, in practice, remember
of course that on 30m any antenna is going to perform better generally for any
given height, than on 40m, so in reality of on air practice, I think no
disadvantage in the slightly less power on 30m, aside from the fact it is only
around 1dB in my case, e.g. getting 2W instead of 3W, or 3W instead of 4W,
depending on the voltage. So I'm happy with it. I'd like to find some cheap PA
that would be a separate kit that would take power up to say 10W or so but could
not find any such from searching eBay.
|
Re: DVM/RF detector header Question
I also seem to remember some other folks getting low RF output because a toroid underneath the LCD screen would contact one of the tabs holding the screen in place. ?I bent the mounting tab flat against the LCD board on mine. ?I would do it to yours too just to be safe.?
|
R: Re: [QRPLabs] Boxing the QCX
Good info. I bought it in UK, shipping time is short than Thailand. For EU country there are import tax+vat too from Thai (not for UK).
Best regards
Fabrizio
Inviato dal mio dispositivo Samsung -------- Messaggio originale -------- Da: John Payne <payne0j@...> Data: 13/12/2017 15:51 (GMT+01:00) A: [email protected] Oggetto: Re: [QRPLabs] Boxing the QCX
For what it's worth, Tayda has the Hammond 1590BB painted for
$6.99.?
No affiliation or pecuniary interest, just trying to help.
W4CWZ
On 12/12/2017 10:16 AM, Jonathan
Bresler wrote:
toggle quoted message
Show quoted text
Martin,
Thank you.? Those look like very nice enclosures.
Jonathan
|
Shirley Dulcey KE1L
Kurt Zimmerman
Paul Jorgenson KE7HR
?
??