Re: #qmx PTT Control
#qmx
One more for the pile:
I have both QMX 80-20M and 20-10M versions, both are working like champs, excellent DX all around, running 014 firmware.?
But PTT isn't working at all on either version of the QMX, both on the "TX PTT +5V? and "TX PTT grounded"? (open collector, tested with a 10K pullup resistor to 5V) as enabled in band configuration. No output on either, not when transmitting from WSJT (with PTT configured for CAT), not from from by pressing the "p" button in diagnostics in the terminal interface, and not from pressing T either. It's just not working on either radio with pretty much identical behavior.?
I'll be glad when this gets fixed up. Meanwhile, is there any work-around? Any point on the board where we can pull a PTT signal from? What about the terrible hack of a current sensor on the QMX power input that triggers a relay? Might be more preferable than soldering to the board.
Coincidentally, I've also only noticed this as I begin to experiment with the 50W amp.
Cheers,
Andy KA1PLU
|
Just had a thought, you do have Minicom not running when you try to connect to Wsjtx don't you?
toggle quoted message
Show quoted text
Hmmm... I've never used Minicom so don't know why it would comeup at the Configuration screen rather than the normal initial screen.?
Did you get the first 5 items on the webpage for QDX is alive and talking?
Did you check the items following? ?
What results?
If nothing else stands out you'll need to do a "forced firmware update" and reload the firmware - See the bottom of the web page. I've never done that, but it doesn't sound difficult. The EPROM chip is between the CPU and the edge of the circuit board.
Cliff, super, thanks,
? restarting the qdx, rebooting the pc.
? I started up everything again.
? in Minicom I see the?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TCXO frequency ? ? ? ?25000000 ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Sideband ? ? ? ? ? ? ? ? ? ?USB ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Default frequency ? ? 14074000 ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VOX ? ? ? ? ? ? ? ? ? ? ? ? ? ?DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Rise threshold ? ? ? ? ?80 ? ? ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Fall threshold ? ? ? ? ? 60 ? ? ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum cycles ? ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum samples ? 480 ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Discard cycles ? ? ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?IQ mode ? ? ? ? ? ? ? DISABLE ? ? ?
Screen, I am not at the ?normal config screen, and CAT does not work from wsjtx on the win10 computer.
I am still with no CAT running, and a "wrong screen". ?I saw the correct screen 3 days ago. and was able to excercise the configuration options. ?I cant get there now.
Can I find the key stroke needed to manually change from the TCXO Screen to the Config Screen that QRP-LABS says to look for on power?
--
K1TE, BRADSHAW LUPTON, Buzzards Bay Radio Club,. WB2TEV, on hhe Cape Cod Canal, an hour south of Boston, MA
|
I'd use putty from the Pi.
Minicom is an old terminal emulater. Used it on 386 computers. It sounds like the way it handles end-of-line is not configured properly. If I remember correctly it can either send CR/LF LF or CR at end-of line. Maybe more. Also could be sending X-ON/X-OFF characters. If it's sending extra characters when you hit enter it will send you to screens you don't want. Can't help you with minicom. It's been too long.
Try installing putty and use it in serial mode.?
--
John KY4WW
|
Hmmm... I've never used Minicom so don't know why it would comeup at the Configuration screen rather than the normal initial screen.?
Did you get the first 5 items on the webpage for QDX is alive and talking?
Did you check the items following? ?
What results?
If nothing else stands out you'll need to do a "forced firmware update" and reload the firmware - See the bottom of the web page. I've never done that, but it doesn't sound difficult. The EPROM chip is between the CPU and the edge of the circuit board.
toggle quoted message
Show quoted text
Cliff, super, thanks,
? restarting the qdx, rebooting the pc.
? I started up everything again.
? in Minicom I see the?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TCXO frequency ? ? ? ?25000000 ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Sideband ? ? ? ? ? ? ? ? ? ?USB ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Default frequency ? ? 14074000 ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VOX ? ? ? ? ? ? ? ? ? ? ? ? ? ?DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Rise threshold ? ? ? ? ?80 ? ? ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Fall threshold ? ? ? ? ? 60 ? ? ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum cycles ? ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum samples ? 480 ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Discard cycles ? ? ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?IQ mode ? ? ? ? ? ? ? DISABLE ? ? ?
Screen, I am not at the ?normal config screen, and CAT does not work from wsjtx on the win10 computer.
I am still with no CAT running, and a "wrong screen". ?I saw the correct screen 3 days ago. and was able to excercise the configuration options. ?I cant get there now.
Can I find the key stroke needed to manually change from the TCXO Screen to the Config Screen that QRP-LABS says to look for on power?
--
K1TE, BRADSHAW LUPTON, Buzzards Bay Radio Club,. WB2TEV, on hhe Cape Cod Canal, an hour south of Boston, MA
|
Re: #qnx #firmware ALPHA 1_00_015 called 00000000.zip
#qnx
#firmware
Hi All I've only had a chance to try 15 alpha this evening so apologies if this has all already been said.? I've been testing it by dabbling in the EUDX contest at between 24 to 28 wpm.? I use iabic B with paddles swapped:
- Sidetone seems clickier and somehow busier than it did on 14, not as easy to listen to.? I think this might be why some have commented that it sounds faster than set, It does sound fast but actually matches the RBN pretty well.
- It sometimes elongates a dit so e becomes t.? Seems to happen most at the e of the eul in my call.??
- Sometimes seem to hesitate then rush to catch up so the characters bunch up
- I don't think any of these anomalies happen at the beginning of an over.? Its almost as if some memory or buffer is getting used up then it starts to become erratic.? Is a memory leak possible with a QMX?? ??
- I've also noticed that the tune/SWR function is stuck on 80m.
- Sometimes it misses characters, it sometimes leaves a gap, sometimes misses then rushes and bunches the next character.??
I'm not very good at systematically testing and these issues are not happening all the time but will definitely happen a few times in a qso and once it starts happening it gets more frequent (I think).? Hope these observations help the overall gathering of info.? Good luck Hans! 73 Peter GM0EUL
|
Re: Request for QMX troubleshooting guidance
Lloyd,
With power off, check the resistance from TX to ground. Is it low/shorted?
Check for continuity from the MCU TX pin to the '08 TX inputs. Is the solder joint at the MCU pin good?
JZ
On Sat, Feb 3, 2024, 3:35?PM Lloyd Milligan < himself@...> wrote: Hello, ? I have just completed assembly of the 20-to-10 meter QMX. Controls and inputs are good (firmware 1_00_014). Receive works very well¡ªgreat sensitivity. However, no RF output on any band. ? On key-down, CLK2 makes it through the XORs but not through the 7408. The latter¡¯s Tx inputs (2, 3, 10, 13) do not change state on key-down (The IC has power and the CLK2 inputs have signal). Thus there is no RF input to the BS170s. I would be grateful for a suggestion as to where to check next. ? Thank you, Lloyd (wa4efs)
|
Cliff, super, thanks,
? restarting the qdx, rebooting the pc.
? I started up everything again.
? in Minicom I see the?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TCXO frequency ? ? ? ?25000000 ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Sideband ? ? ? ? ? ? ? ? ? ?USB ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Default frequency ? ? 14074000 ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VOX ? ? ? ? ? ? ? ? ? ? ? ? ? ?DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Rise threshold ? ? ? ? ?80 ? ? ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Fall threshold ? ? ? ? ? 60 ? ? ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum cycles ? ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum samples ? 480 ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Discard cycles ? ? ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?IQ mode ? ? ? ? ? ? ? DISABLE ? ? ?
Screen, I am not at the ?normal config screen, and CAT does not work from wsjtx on the win10 computer.
I am still with no CAT running, and a "wrong screen". ?I saw the correct screen 3 days ago. and was able to excercise the configuration options. ?I cant get there now.
Can I find the key stroke needed to manually change from the TCXO Screen to the Config Screen that QRP-LABS says to look for on power?
--
K1TE, BRADSHAW LUPTON, Buzzards Bay Radio Club,. WB2TEV, on hhe Cape Cod Canal, an hour south of Boston, MA
|
It looks like you hit enter once too often or clicked on the top item in the list "Configuration". What you should see when you click the top line in the "expected" view. I seriously doubt there is anything wrong with the QDX.
Isn't Wsjtx work any more?
toggle quoted message
Show quoted text
On Feb 3, 2024, at 15:55, bradshawlupton.k1te < k1te@...> wrote:
thank you, I am not getting the screen that QRP-LAB shows in the PC trouble shooting.
I connected via minicom 9600,n,8,1 and expected to get the screen shown under?
? ?QDX IS ALIVE AND TALKING ? ? from ?
I got this correct screen when I first powered up the unit, after it arrived assembled from QRP-LABS.
I receive this "wrong" screen, ?I can type on this screen, it is rx and tx over serial comms, so the cable is good, 9600,N,8,1 from the pi4 running Bullseye 11.
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TCXO frequency ? ? ? ?25000000 ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Sideband ? ? ? ? ? ? ? ? ? ?USB ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Default frequency ? ? 14074000 ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VOX ? ? ? ? ? ? ? ? ? ? ? ? ? ?DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Rise threshold ? ? ? ? ?80 ? ? ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Fall threshold ? ? ? ? ? 60 ? ? ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum cycles ? ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum samples ? 480 ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Discard cycles ? ? ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?IQ mode ? ? ? ? ? ? ? DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Japanese band limits ?DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout enable ? ?ENABLE ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout (sec) ? ? 120 ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PTT Port as Serial 3 ?DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VGA PS/2 terminal ? ? DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 1 terminal ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 2 terminal ? ? 0 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 3 terminal ? ? 0 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Night mode ? ? ? ? ? ?DISABLE ??
? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TX shift threshold ? ?500 ????
How may I "get off" this screen, back to the correct starting screen.
From this wrong screen, TEST CAT always fails.
Thank you, Bradshaw K1TE. (also thank you also for the very quick response)
? ? ? ? ? ? ? ? ? ? Excited about seeing this run.
Would you know the keystrokes to get the QDX back to the normal QDX Alive and talking screen listed on?? the trouble shooting link above?
?? ? ? ? ? ? ? ? ? ? ? ? ? ? ??
On Saturday, February 3rd, 2024 at 4:07 PM, Cliff < ae5zaham@...> wrote:
Please say what do you mean by "confused state".
What are you referring to as the "normal" initial screen??
It isn't clear to me what you are experiencing that is a problem.
To do a hardware reset you need to open Putty and get to the config screens in the QDX.
The page you see in Bitcom is the main config screen in the QDX and it all looks normal.
Normally The TX Threshold is set to zero, but I understand it should work at the default also.
I have a good 9600 baud connection, two way, from a pi4 to the QDX. ?The poor brand new QDX is in ?confused state.
? ? Things came up correctly, brand new, 4 days ago. ? ?
? ? It RX'ed on 20m, 17m and 15m for 3 days nicely. ?Using WSJTX-2.6.1 and?"Raspbian GNU/Linux 11 (bullseye)"
?
? ? I would like to return to "factory default". ? ?
? ?I am an absolute vanila new user. ?I'd like to RX for a week and test the QDX before I TX
? ?Is there a keystroke I should know to "get back" / "return" ?to the "normal" initial screen.
? ? ? ? ? Thanks for any suggestion. ?Bradshaw K1TE
Should wsjtx 2.6.1 ?recognize this screen and resolve the communications across serial?
Welcome to minicom 2.8 ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TCXO frequency ? ? ? ?25000000 ? ? ? ? ??OPTIONS: I18n ? ? ? ? ? ? ? ? ? ?Sideband ? ? ? ? ? ? ?USB ? ? ? ? ? ? ? ?Port /dev/modem, 14:50:20 ? ? ? ?Default frequency ? ? 14074000 ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VOX ? ? ? ? ? ? ? ? ? DISABLE ? ? ? ? ? ?Press CTRL-A Z for help on speciaRise threshold ? ? ? ?80 ? ? ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Fall threshold ? ? ? ?60 ? ? ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum cycles ? ? ? ?1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum samples ? ? ? 480 ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Discard cycles ? ? ? ?1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?IQ mode ? ? ? ? ? ? ? DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Japanese band limits ?DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout enable ? ?ENABLE ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout (sec) ? ? 120 ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PTT Port as Serial 3 ?DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VGA PS/2 terminal ? ? DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 1 terminal ? ? 1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 2 terminal ? ? 0 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 3 terminal ? ? 0 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Night mode ? ? ? ? ? ?DISABLE ??? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TX shift threshold ? ?500 ? ?? -- K1TE, BRADSHAW LUPTON, Buzzards Bay Radio Club,. WB2TEV, on hhe Cape Cod Canal, an hour south of Boston, MA
|
Re: #qnx #firmware ALPHA 1_00_015 called 00000000.zip
#qnx
#firmware
I attempted to ENABLE the TX PTT+5 volt setting and encountered the same problem as Adrian, YO3GFH. The ENABLE setting reverts back to DISABLE after leaving the terminal. Other settings such as Transmit (I DISABLED the 11-meter band) and audio gain settings did not revert to their original settings.
Dennis
KK5DB
|
thank you, I am not getting the screen that QRP-LAB shows in the PC trouble shooting.
I connected via minicom 9600,n,8,1 and expected to get the screen shown under?
? ?QDX IS ALIVE AND TALKING ? ? from ?
I got this correct screen when I first powered up the unit, after it arrived assembled from QRP-LABS.
I receive this "wrong" screen, ?I can type on this screen, it is rx and tx over serial comms, so the cable is good, 9600,N,8,1 from the pi4 running Bullseye 11.
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TCXO frequency ? ? ? ?25000000 ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Sideband ? ? ? ? ? ? ? ? ? ?USB ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Default frequency ? ? 14074000 ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VOX ? ? ? ? ? ? ? ? ? ? ? ? ? ?DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Rise threshold ? ? ? ? ?80 ? ? ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Fall threshold ? ? ? ? ? 60 ? ? ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum cycles ? ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum samples ? 480 ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Discard cycles ? ? ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?IQ mode ? ? ? ? ? ? ? DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Japanese band limits ?DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout enable ? ?ENABLE ? ? ? ? ? ??
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout (sec) ? ? 120 ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PTT Port as Serial 3 ?DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VGA PS/2 terminal ? ? DISABLE ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 1 terminal ? ? 1 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 2 terminal ? ? 0 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 3 terminal ? ? 0 ? ? ? ? ? ? ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Night mode ? ? ? ? ? ?DISABLE ??
? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TX shift threshold ? ?500 ????
How may I "get off" this screen, back to the correct starting screen.
From this wrong screen, TEST CAT always fails.
Thank you, Bradshaw K1TE. (also thank you also for the very quick response)
? ? ? ? ? ? ? ? ? ? Excited about seeing this run.
Would you know the keystrokes to get the QDX back to the normal QDX Alive and talking screen listed on?? the trouble shooting link above?
?? ? ? ? ? ? ? ? ? ? ? ? ? ? ??
On Saturday, February 3rd, 2024 at 4:07 PM, Cliff <ae5zaham@...> wrote:
Please say what do you mean by "confused state".
What are you referring to as the "normal" initial screen??
It isn't clear to me what you are experiencing that is a problem.
To do a hardware reset you need to open Putty and get to the config screens in the QDX.
The page you see in Bitcom is the main config screen in the QDX and it all looks normal.
Normally The TX Threshold is set to zero, but I understand it should work at the default also.
I have a good 9600 baud connection, two way, from a pi4 to the QDX. ?The poor brand new QDX is in ?confused state.
? ? Things came up correctly, brand new, 4 days ago. ? ?
? ? It RX'ed on 20m, 17m and 15m for 3 days nicely. ?Using WSJTX-2.6.1 and?"Raspbian GNU/Linux 11 (bullseye)"
?
? ? I would like to return to "factory default". ? ?
? ?I am an absolute vanila new user. ?I'd like to RX for a week and test the QDX before I TX
? ?Is there a keystroke I should know to "get back" / "return" ?to the "normal" initial screen.
? ? ? ? ? Thanks for any suggestion. ?Bradshaw K1TE
Should wsjtx 2.6.1 ?recognize this screen and resolve the communications across serial?
Welcome to minicom 2.8 ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TCXO frequency ? ? ? ?25000000 ? ? ? ? ??OPTIONS: I18n ? ? ? ? ? ? ? ? ? ?Sideband ? ? ? ? ? ? ?USB ? ? ? ? ? ? ? ?Port /dev/modem, 14:50:20 ? ? ? ?Default frequency ? ? 14074000 ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VOX ? ? ? ? ? ? ? ? ? DISABLE ? ? ? ? ? ?Press CTRL-A Z for help on speciaRise threshold ? ? ? ?80 ? ? ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Fall threshold ? ? ? ?60 ? ? ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum cycles ? ? ? ?1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum samples ? ? ? 480 ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Discard cycles ? ? ? ?1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?IQ mode ? ? ? ? ? ? ? DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Japanese band limits ?DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout enable ? ?ENABLE ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout (sec) ? ? 120 ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PTT Port as Serial 3 ?DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VGA PS/2 terminal ? ? DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 1 terminal ? ? 1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 2 terminal ? ? 0 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 3 terminal ? ? 0 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Night mode ? ? ? ? ? ?DISABLE ??? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TX shift threshold ? ?500 ? ?? -- K1TE, BRADSHAW LUPTON, Buzzards Bay Radio Club,. WB2TEV, on hhe Cape Cod Canal, an hour south of Boston, MA
|
Re: #qnx #firmware ALPHA 1_00_015 called 00000000.zip
#qnx
#firmware
A few things I noticed after playing with this firmware today:
1. The CW-R and Sideband parameters still have no effect when altered via the System Config menu.
2. When entering the "Tune SWR" function, the frequency displayed used to be that of the current VFO setting. i.e. if the radio was tuned to 14.030 MHz, that's what the SWR tuning frequency was set to. Now, when entering the Tune SWR function, the frequency is set to the 80m band.
3. I tried paddles at 20WPM and the keyer still chopped the occasional DAH which, for an MM0 callsign like me, is a bit nippy.
4. The right rotary encoder debouncing still seems a bit off as it can sometimes take a few counter-clockwise clicks before the radio responds. This is most noticeable in the menu system. Not new to this firmware version though.
5. Straight key operation is a joy at 20 WPM-ish so I'm a very happy camper. :o)
Cheers,
Ronan
MM0IVR
|
Please say what do you mean by "confused state".
What are you referring to as the "normal" initial screen??
It isn't clear to me what you are experiencing that is a problem.
To do a hardware reset you need to open Putty and get to the config screens in the QDX.
The page you see in Bitcom is the main config screen in the QDX and it all looks normal.
Normally The TX Threshold is set to zero, but I understand it should work at the default also.
toggle quoted message
Show quoted text
I have a good 9600 baud connection, two way, from a pi4 to the QDX. ?The poor brand new QDX is in ?confused state.
? ? Things came up correctly, brand new, 4 days ago. ? ?
? ? It RX'ed on 20m, 17m and 15m for 3 days nicely. ?Using WSJTX-2.6.1 and?"Raspbian GNU/Linux 11 (bullseye)"
?
? ? I would like to return to "factory default". ? ?
? ?I am an absolute vanila new user. ?I'd like to RX for a week and test the QDX before I TX
? ?Is there a keystroke I should know to "get back" / "return" ?to the "normal" initial screen.
? ? ? ? ? Thanks for any suggestion. ?Bradshaw K1TE
Should wsjtx 2.6.1 ?recognize this screen and resolve the communications across serial?
Welcome to minicom 2.8 ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TCXO frequency ? ? ? ?25000000 ? ? ? ? ??OPTIONS: I18n ? ? ? ? ? ? ? ? ? ?Sideband ? ? ? ? ? ? ?USB ? ? ? ? ? ? ? ?Port /dev/modem, 14:50:20 ? ? ? ?Default frequency ? ? 14074000 ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VOX ? ? ? ? ? ? ? ? ? DISABLE ? ? ? ? ? ?Press CTRL-A Z for help on speciaRise threshold ? ? ? ?80 ? ? ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Fall threshold ? ? ? ?60 ? ? ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum cycles ? ? ? ?1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum samples ? ? ? 480 ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Discard cycles ? ? ? ?1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?IQ mode ? ? ? ? ? ? ? DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Japanese band limits ?DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout enable ? ?ENABLE ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout (sec) ? ? 120 ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PTT Port as Serial 3 ?DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VGA PS/2 terminal ? ? DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 1 terminal ? ? 1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 2 terminal ? ? 0 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 3 terminal ? ? 0 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Night mode ? ? ? ? ? ?DISABLE ??? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TX shift threshold ? ?500 ? ?? -- K1TE, BRADSHAW LUPTON, Buzzards Bay Radio Club,. WB2TEV, on hhe Cape Cod Canal, an hour south of Boston, MA
|
Request for QMX troubleshooting guidance
Hello, ? I have just completed assembly of the 20-to-10 meter QMX. Controls and inputs are good (firmware 1_00_014). Receive works very well¡ªgreat sensitivity. However, no RF output on any band. ? On key-down, CLK2 makes it through the XORs but not through the 7408. The latter¡¯s Tx inputs (2, 3, 10, 13) do not change state on key-down (The IC has power and the CLK2 inputs have signal). Thus there is no RF input to the BS170s. I would be grateful for a suggestion as to where to check next. ? Thank you, Lloyd (wa4efs)
|
I have a good 9600 baud connection, two way, from a pi4 to the QDX. ?The poor brand new QDX is in ?confused state.
? ? Things came up correctly, brand new, 4 days ago. ? ?
? ? It RX'ed on 20m, 17m and 15m for 3 days nicely. ?Using WSJTX-2.6.1 and?"Raspbian GNU/Linux 11 (bullseye)"
?
? ? I would like to return to "factory default". ? ?
? ?I am an absolute vanila new user. ?I'd like to RX for a week and test the QDX before I TX
? ?Is there a keystroke I should know to "get back" / "return" ?to the "normal" initial screen.
? ? ? ? ? Thanks for any suggestion. ?Bradshaw K1TE
Should wsjtx 2.6.1 ?recognize this screen and resolve the communications across serial?
Welcome to minicom 2.8 ? ? ?
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TCXO frequency ? ? ? ?25000000 ? ? ? ? ??OPTIONS: I18n ? ? ? ? ? ? ? ? ? ?Sideband ? ? ? ? ? ? ?USB ? ? ? ? ? ? ? ?Port /dev/modem, 14:50:20 ? ? ? ?Default frequency ? ? 14074000 ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VOX ? ? ? ? ? ? ? ? ? DISABLE ? ? ? ? ? ?Press CTRL-A Z for help on speciaRise threshold ? ? ? ?80 ? ? ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Fall threshold ? ? ? ?60 ? ? ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum cycles ? ? ? ?1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Minimum samples ? ? ? 480 ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Discard cycles ? ? ? ?1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?IQ mode ? ? ? ? ? ? ? DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Japanese band limits ?DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout enable ? ?ENABLE ? ? ? ? ? ??? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?CAT timeout (sec) ? ? 120 ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?PTT Port as Serial 3 ?DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?VGA PS/2 terminal ? ? DISABLE ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 1 terminal ? ? 1 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 2 terminal ? ? 0 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Serial 3 terminal ? ? 0 ? ? ? ? ? ? ? ? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?Night mode ? ? ? ? ? ?DISABLE ??? ?? ? ? ? ? ? ? ? ? ? ? ? ? ? ?TX shift threshold ? ?500 ? ?? -- K1TE, BRADSHAW LUPTON, Buzzards Bay Radio Club,. WB2TEV, on hhe Cape Cod Canal, an hour south of Boston, MA
|
Re: QMX V2 and MAC Air M2 - connecting for digital
Phil,
What did you set as the receive audio card in the Wsjtx Audio config? Maybe a screen shot of that page would be helpful.
toggle quoted message
Show quoted text
On Feb 3, 2024, at 13:54, PHILIP GRAITCER via < pgraitc@...> wrote:
My QMX works fine for CW, but I am unable to connect it to my MacAir M2 for digital modes. I am using TS-440S as transceiver type and?/dev/tty.usbmodem1101 as my serial port and CAT for PTT method. I am able to get the receive and transmit buttons to light green and red. I am also getting an increased current draw and on screen there is a solid line under the band letter A,? indicating, according to the manual, that all is well for transmitting.
But I am not able to receive signals. I just get horizontal green lines and nothing else on the WSJT waterfall.
So, sound is not getting from the QMX to the computer program. (I can hear the signals if I listen through the audio port on QMX.)
I'm sure I am missing something simple. Can someone suggest what it might be?
Phil K3UT
|
QMX V2 and MAC Air M2 - connecting for digital
My QMX works fine for CW, but I am unable to connect it to my MacAir M2 for digital modes. I am using TS-440S as transceiver type and?/dev/tty.usbmodem1101 as my serial port and CAT for PTT method. I am able to get the receive and transmit buttons to light green and red. I am also getting an increased current draw and on screen there is a solid line under the band letter A,? indicating, according to the manual, that all is well for transmitting.
But I am not able to receive signals. I just get horizontal green lines and nothing else on the WSJT waterfall.
So, sound is not getting from the QMX to the computer program. (I can hear the signals if I listen through the audio port on QMX.)
I'm sure I am missing something simple. Can someone suggest what it might be?
Phil K3UT
|
Re: QMX continuity test problem
Thank you Scott, I think I¡¯ll give that a try as well.?
Cheers
Dave
|
Re: QMX on a stick - a minimalistic SOTA activation
#qmx
Fantastic.
The spirit of ham radio !
--
- 73 de Andy -
|
Re: QMX on a stick - a minimalistic SOTA activation
#qmx
Nice setup. This gives me ideas for the station I want to carry on hiking trips in the mountains with the YL.
73!
Kevin
N8MXL
|
Re: QMX continuity test problem
Hi David. I had similar issue. Had continuity between the A points if I touched the tip of the wire, but only continuity between one set of A pads if I touched the pads. What that told me is that one, of the two wires that come through ?at point A from the windings of the power amp still had some enamel on it. Went back and really heated and re-soldered the two wires and that resolved the issue. Works like a charm now.?
|
John KY4WW
Peter GM0EUL
bradshawlupton.k1te
David KO4EOD