开云体育

I've just upgraded from 020 to 027 and the RTC resets to 00:00 when it is powered off. I'm sure that the RTC kept time before I upgraded the firmware. Have I missed something in the set up? Thanks

Man, running a physical product business sounds like a real PITA.

Thank you. I actually figured that out after I asked, but I'm still a n00b and jargon is not always obvious to me. /m

Hello, All. 1. Can someone tell me what might be causing an intermittent reading when I perform the Image scan for 20 meters? (high band unit, 12 V/1.1 A p.s. settings, 95 mA rx, 20 watt dummy load

Very good progress. Greg's suggestion #1 is a good one.? Maybe also take a close-up photo of your T501 and post it so we can see what you did and maybe help. If both the board and the coil test good

Hi Bojan, Thanks for the hint, PTT voltage when in TX is only 2.5V. And Red LED is not as bright as green one. Now I need to find the culprit. I measured R14 in-circuit to be 9.96kohm, which looks

If you do a diagnostics LPF scan for 15M, what does it show? (using the USB interface via putty or teraterm or whatever terminal emulator) You potentially have a 15M LPF problem.

between Source and Drain. Sorry, but IMHO without an idea about such things its hard to debug such a device and its hard to explain all this in a post here. Yes and if broken it must be

On Fri, Sep 27, 2024 at 08:06 AM, @Ludwig_DH8WN wrote: 1. Looking at picture 6 and 7 I see something light green at a solder of T507. What is it? PCB Mask. I rewound T507 3 times and I scratched the

I got both 17 and 15 meters to over 4 watts. This is what I did, I put more heat on the solder joints and adjusted the windings to have more space. I thought since the calculated windings were

Ludwig, First of all, thank you for this. I have been trying to parse the schematics, but I don't fully know all the causes and effects. This helps a lot. I was with you, pretty much, right 'til the

Hello Michael, ok, lets have a look at schematics. Bias current is "produced" by an SMPS built from Q501, Q502, Q516 and the parts around. When Q502 is switched on, energy is flowing from "+12V" to

Hans,? w0wly, Thanks for your replies. That's a relief! I searched the group with several keywords but found no reports of the behavior. It's not a big deal. It only adds two rapid +/- key presses

Progress !? :) Greg Yahoo Mail: Search, Organize, Conquer On Fri, Sep 27, 2024 at 11:00 AM, Don DeGregori<ddegreg1@...> wrote: I finally found the right Com port. It is Com 4. I guess

The table below shows power output, using two independent meters.? Meter 1 is on a QRP tuner, Meter 2 is a stand-alone QRP power/SWR meter.? While they differ in values, they both show 15m power

Jeff is 100% right, no question. The problem with applying the advice "fix what's broken" is, i don't know what's broken, **and** I don't know how to figure out what's broken. I am missing one key

Exactly. Probably, you could also do, `sudo dmesg|grep ACM`, since it should always at least come in as an ACM-named device.

I always use sudo dmesg | less and then hit shift G to go to the bottom and scroll up until I find the device and path.

The good news is, if you always plug in to the same USB port, it should always show up as the same COM port going forward. The bad news is, if you forget and plug in to a different USB port, it will

Yes, the output for 17/15, I'll adjust L513, thanks for the suggestion!