开云体育

Mach3 mill stopped in the middle of a job.

Mark Zirinsky All Messages By This Member #155487 开云体育 Mach3 notorious for not working well on a laptop, usually power savings features of a laptop cause issues ? toggle quoted message Show quoted text From: [email protected] <[email protected]> On Behalf Of Chuck Kahler Sent: Friday, January 12, 2024 12:14 PM To: [email protected] Subject: Re: [MachCNC] Mach3 mill stopped in the middle of a job. ? Mike, That was my thought At first, then I remembered this little guy doesn’t have any limit switches on it. ? ? I’m wondering if something could’ve happened to the parallel port itself within the laptop computer.? ? I say this because I tried two different control boxes and it made no difference. ? Thanks for your input, Chuck ? ? -sent from my iphone -- ? ? On Jan 12, 2024, at 10:36?AM, mike allen <animal@...> wrote: ? ??? ??? Limit switch & wires all good ? animal On 1/12/24 10:02 AM, Chuck Kahler wrote: I have a TAIG desktop Mill with a PMDX – 122 motion control board that utilizes a parallel port. ? The machine has always run without problem and in the middle of a 15 minute milling job it stopped about halfway and I cannot get the machine to respond no matter what I try. ? I even replaced the control box, which I had a spare, that ?included the?PMDX -122 motion control, and Gecko drivers, and that did not help. anybody have any ideas what could’ve caused this? ? Thanks, Chuck ? ? ?
Chuck Kahler All Messages By This Member #155486 开云体育 Mike, That was my thought At first, then I remembered this little guy doesn’t have any limit switches on it. ? I’m wondering if something could’ve happened to the parallel port itself within the laptop computer.? I say this because I tried two different control boxes and it made no difference. Thanks for your input, Chuck toggle quoted message Show quoted text -sent from my iphone -- On Jan 12, 2024, at 10:36?AM, mike allen <animal@...> wrote: ? ??? ??? Limit switch & wires all good ? animal On 1/12/24 10:02 AM, Chuck Kahler wrote: I have a TAIG desktop Mill with a PMDX – 122 motion control board that utilizes a parallel port. ? The machine has always run without problem and in the middle of a 15 minute milling job it stopped about halfway and I cannot get the machine to respond no matter what I try. ? I even replaced the control box, which I had a spare, that ?included the?PMDX -122 motion control, and Gecko drivers, and that did not help. anybody have any ideas what could’ve caused this? ? Thanks, Chuck ? ? ?
mike allen All Messages By This Member #155485 开云体育 ??? ??? Limit switch & wires all good ? animal On 1/12/24 10:02 AM, Chuck Kahler wrote: toggle quoted message Show quoted text I have a TAIG desktop Mill with a PMDX – 122 motion control board that utilizes a parallel port. ? The machine has always run without problem and in the middle of a 15 minute milling job it stopped about halfway and I cannot get the machine to respond no matter what I try. ? I even replaced the control box, which I had a spare, that ?included the?PMDX -122 motion control, and Gecko drivers, and that did not help. anybody have any ideas what could’ve caused this? ? Thanks, Chuck ? ? ?
Chuck Kahler All Messages By This Member #155484 I have a TAIG desktop Mill with a PMDX – 122 motion control board that utilizes a parallel port. ? The machine has always run without problem and in the middle of a 15 minute milling job it stopped about halfway and I cannot get the machine to respond no matter what I try. ? I even replaced the control box, which I had a spare, that ?included the?PMDX -122 motion control, and Gecko drivers, and that did not help. anybody have any ideas what could’ve caused this? ? Thanks, Chuck ? ? ?

Previous Topic Next Topic