开云体育

Hello Art, I am getting a machine setup to try out the digitizing pulse you put in. I need to call the mach2 ocx from another program. Are the OCX functions documented anywhere? Thanks, Tom

Gigabyte then that's more than likely the problem because that board seems to have absolutely no tolerance for Mach2. Servo Agree. Gigabyte AMD board just does not work. Roger s

John: Right again, I will raise the limit to M9999 Thanks, Art www.artofcnc.ca

John: Thanks, a bug I think. I will test it out... I recommend the last thing you do before pressing cycle start is to set the repitions. They are disabled with an E-Stop reset so it can be a bit

I was thinking of documenting to users that they should start writing their own macros numbering from M100. The Configure>Macros dialog will happily open/save M101.M1S but MDI and Part Program won't

file <snip> Thanks I put in the M30 - and a Return! and after several attempts it ran wonderfully, decrementing the count and lowering Z-inhibit. I tried some different values and it ran again - but

Hi Frank: Play with your acceleration values. The CV mode is highly influenced by them. It will round the vectors at axis direction change points due to the CV methods used. One axis is decel. while

Hello folks, I have a problem with running this code (a segment) with constant velocity on in RC11. Especially if I enable feedrate overide on, the lead out from the radii to the straight away causes

Steve: I don't think anything runs Lathe well yet. ;) (Also, start calling it Turn or I'll sick John on you...) Thanks, Art www.artofcnc.ca

Larry: The install locks up? Hmm, I have heard of bad installs downloading. Try to right click and select save as, this sometimes forces it to finish. You may have a bad download. Compare the new

John: My fault, I never explained that an M30 must be at the end of a file you wish to do a repeat on. The rewind must be explicity set, otherwise the repeat trigger will not fire. (You'd think I'd

Steve: Well, the numbers are getting better, but I don't understand the dual movement. I just finished a 15 hour shift, so I will try to get to this tommorrow. Obviously, I have a problem with

That's a bit of a sweeping statement? I've now got 3 PC's here, one of which is a Gigabyte and it runs Mach2 mill fine (The others are an Asus and an Intel) None run lathe well though... -- Steve

Hi, What brand of mainboard does your computer have? If you answer with Gigabyte then that's more than likely the problem because that board seems to have absolutely no tolerance for Mach2. Servo

Any error message? RC3 to date has had so many changes! 7th July to date is at least 4 versions plus many of Art's phantom ones, plus registry to XML in V6 for settings!! What OS are you running? If

Hi Art I downloaded release version 1.0 and tried to install it. The install program locks up after it is started. I downloaded it a 2nd time with the same results. Tried restarting windows with no

Hi Perhaps I am doing something silly, but with the program: f100 g1 z-10 g1 x10 g1 y20 g1 x0 g1 y0 And Z inhibit set initially to -1.0, Lower Z-inhibit set to 1.0 and repetitions set to 10 I get one

You still forgot to fix macro though ;) Done some more test this morning and things look much more promising on the spindle front. Spindle is not slowing down and is maintaining requested speed plus

Some folks might want to try 2X Editor, this little gem is free, faster and smaller than notepad and wordpad and co-exists happily with Mach2. Try 2XExplorer while you are at it, get used to a two

It has no difference if CV is enabled or disabled, via the menu or the g61/g64 commands. The effect is the same. As I see your algorithm works as follows: The G file is parsed and converted into a