开云体育

Hi MArk: Just me opinion, some do use MachIV, but Ive found experiences seem to vary widely. IT really isnt ready for prime time by my estimation. The Next version will be, but it will take up to 3

Hi Chris: it's time we all got an update on you :-) My lord, it has been 6 months hasnt it. Time fly's. :) It has cut quite a few. Unfortunatley, I destroyed the tailstock and am now rebuilding

I have a large VMC I have retrofitted with mach as well. Currently I'm using Mach3 with the LPT control, and will upgrade to Grex some time after the new dll plugin control for it is released. I'm

I use CoralDraw and Adobe Illustrator, and I feel that Illustrator works the best. I just finished building my 1st homemade CNC machine and I just cut my 1st project with Mach 2 and VCarve Wizard and

Hi Art, It's been about 6 months now I think since you retired, so I figure it's time we all got an update on you :-) How is the lathe conversion coming along - is it cutting parts yet? How is the

I changed the wiring of the Gecko fault to the breakout board and tried different pin setting on the motors The original setting works the best. If I run the Y axis back and forth 5-10 times the motor

Hi Guys: For those with a PlugIn interest, I figured I'd post some things going on..and the results of current testing.. I have modified the SDK to have one Include folder for the MachIncludes that

Scott: Send me your xml as it stands now. We may have gotten crossed on it, Ill make sure that as it stands now, the step/dir works on the spindle..(here anyway. :)

I still have a dead spindle on a machine I am upgrading from M2 to M3. Art tried my XML file, and it works for him......but I get no response from the spindle motor. Interestingly, it still runs

I changed the wiring of the Gecko fault to the breakout board and tried different pin setting on the motors The original setting works the best. If I run the Y axis back and forth 5-10 times the motor

Thanks Guys for the info on the 5 phase stuff. Now I can proceed without worrying about that. Jerry

Hi Justen: The LED's may not light, if noise triggers an estop, then it can be very fast. Check the History button to see if its indicating an Estop or External Estop. If so, then there is a setting

I have one of those 5-phase Vexta motor with corresponding driver and they do work very well with Mach3.

When the program E Stops there are no limit led lit at all if I hit reset the program will run again. I have run the ocx driver test a number of times but I must not be the sharpest knife in the

Hi Junsten: When it Estops, do you get a limit switch error? As to the speed, make sure you run the drivertest.exe program and see that its got a good waveform. Thanks, Art www.artofcnc.ca Videos

Art, You called that one right...scared..are we going to have to start X-Rating Mariss do to the Graphical Blood Letting Scenes! art <fenerty@...> wrote:

I am running a 3axis gantry with gecko 201's and a 750 mhz laptop. The steppers are Mclennan nema34 triple stacks 72 volts. The axis run 5mm pitch ball screws, mach2 is set to drive at 45000

Mike: The OEM may have slower opto's in it. Try a wider pulse width.. Thanks, Art www.artofcnc.ca Videos And Support Forums http://www.machsupport.com Users Map: http://www.frappr.com/machsupport

Well be careful, go out a buy you a set of X-Gears.... you know shin guards, helmet, etc! I am trying to protect my selfish interests here as well. <mariss92705@...> wrote: was that programmed

See, I was right to be scared..:) Thanks, Art www.artofcnc.ca Videos And Support Forums http://www.machsupport.com Users Map: http://www.frappr.com/machsupport