开云体育

Chip, Not sure what you see for a problem, but my observation is that in g91 incremental mode(a model command) when you issue an X0 Y0 Z0 command, nothing will happen because you are basically telling

Hi: Had to go away for week--sailing in the Bahamas!!!! Returned last night and downloaded my mail. Life's Hell, but since I left I have not received any Digests--last one is is #2356--so either

Hello Art: Could the lookahead be set to low I have it at 60. I am running a 750mhz cpu and 25khz in mach3. And should I use enhanced pulsing. Thanks, John in the front of

Hi Chip: I just tore mine out. API drivers in it now.. Motors this weekend I think.. Thanks, Art www.artofcnc.ca Videos And Support Forums http://www.machsupport.com Users Map:

Chip Loads and runs here. What are your aiming at and what do you think is the problem? With 500+ posts a week it really helps to ask a direct question or, of course, give us all some new

Back in late November we posted a special introductory price on the new MP1000-THC digital interface and torch height controller. The special was scheduled to be discontinued Dec 15th (or until we

Hi, Art and All: Would some one look at this Gcode: Let me know the error's of my way's. I now i'm not playing with a full deck of cards, I no there's a (joker) not sure about the

Hi Art and All Posted this some time ago must'a fallen through the crack's again. I have made slight additions to original post below for clarity. Kind'a surprised no coment's maybe a tight group

Hi John: Thats CV feedrate. It tells the ocntroller to not begin blending in the next move, until the feedrate falls below that value. In your case, a ballpark woudl be around

Hi: Sounds liek your not retungin properly after changing the steps/unit.. Yes, BUT, at your setting of 32000, thats about .78IPs or 46IPM. The frequency is in steps/sec not minute.. Dont. Stay

Hello Art: What about the other value that is listed just below the angular limit? I am not sure of its function. It says cv feedrate in front of it and the value is set to +1.00? If I do most

Tin; Thank you for posting this, short and to the point You can always tell the "operator/button pusher" from the "cnc machinist/programmer" by t

It is the 20 tpi screws that are killing you top speed. Do your steppers stall before reaching full speed. Most steppers are only usable to about 1000 rpm before the torque drops off too much.

Hi, I'm new nad just setting up my motors. I have a Taig mill with 20tpi leadscrews. I have 200 step per rev motors (1.8deg) My stepper drivers currently are set for 1/8 step. Multiplying this all

Hi John: Hmm, as I recall its function it shoudl make it worse. The effect is telling the system to not CV any line which exceeds that setting. So if its set to 85, it will do exact sop is the angle

Hi Art . Is your camera broke, pictures man pictures (:~)= Terry and glove into information may

Hi Jim: The screens shoudl look pretty much the same, if not, use view/load layout and load the 1024.set file. Softlimits are set by entering the machine coordinates at which you want your table to

Steve: Does typing M999 in the MDI start the triggering prcoess OK? Thanks, Art www.artofcnc.ca Videos And Support Forums http://www.machsupport.com Users Map: http://www.frappr.com/machsupport

Thank you John Scot --- jherrel680 <jherrel@...> wrote: __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around

...any chance you could post a few photos of your actual screens - the snippets I have seen on the forum look cool - would like to see a full screen !! thanx Aaron