it is fixed. it now defaults to 1" and moves 1" i am thrilled as
I am using fairly expensive compression router bits and would hate
to break one due to a mis jog.
On 12/10/2021 1:20 PM, Steve Stallings
wrote:
Version 2.0.4612 is
the current "release" version. It does not contain the fix.
?
The fix Brian refers
to has been implemented in the development versions on the
FTP site here:
?
?
Do not be tempted to
correct the spelling in the link, the typo is real.
?
The versions here have
not been fully blessed, and may have other quirks. That
said, many people are running them with good results.
?
Regards,
Steve Stallings
?
how do i get the revised version? i downloaded the one on the
site but it has the same revision number. so i didn't bother ti
install it. can you provide a link if it is different from the
one on the site?
On 12/10/2021 11:47 AM, Brian Barker
wrote:
Spencer, I checked the log and I fixed that issue on the
following day
Revision: 4725
Author: brianb
Date: Friday, May 14, 2021 10:25:03 AM
Message:
Mach4GUI: Update to make sure Inc Jogging is matching what is
in the jogging array
----
?We are testing to get a release out now but please know when
you told me about your issue the first time I fixed it :)
Thanks
Brian
______________________________
Brian Barker
Webpage:
the problem with jogging one inch when it says .01" at
startup is also a problem any news on this? i have thelatest
version and verified the problem.
On 12/10/2021 10:35 AM, Gary
wrote:
Ok thanks, but this problem with the
toolpath being off center, has become a real problem for
me..
I just ram a job this morning.. I
started by probing to find the center of part, when
centered I zeroed the X and Y
Then loaded the tool and probed the
tool Hight so that was set, then loaded the g code file.
Checked the X and Y they were at zero
the z was at the correct height.
Started to run the job the X and Y
went no where near the correct position and the z dove
into the part¡ wrecked part now
So I flipped over and did the same
thing exactly and it cut prefect . .
I have had this happen before when I
run the part the first time if I re zero center
everything and try again it runs fine..
I have tried this on 3 different
computers also
Any suggestions,
Gary
Sent from for Windows
From:
Brian Barker
Sent: Thursday, December 9, 2021 3:46 PM
To: [email protected]
Subject: Re: [MachCNC] Question about Macros
and dialog box's, and or messagebox
All new to me.. Lets get what we can for data and see
what we can find. I think that is the best thing to do.
Thanks
Brian
______________________________
?
Brian Barker
?
Webpage:
On 12/9/2021 2:55 PM, Gary wrote:
Ok Thanks Brian
I have run into another problem, not sure what the
cause..
when i load the gcode file it never shows the
machining to start in the parts center in the tool
path display... form a couple of my profiles, if i
start a run and then stop re zero the dro's and regen
the tool path its now starting in the middle.. in the
tool path display..
but i do have a couple profiles that don't have that
problem i don't see any setting's that are different.
Do the profiles go bad? or get some sort of glitch,
don't see any difference other than the way the tool
path starts when the gcode is first loaded and its way
off center position
Gary
--
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only
Laytonville, CA 9545 UPS/Fedex only
--
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only
Laytonville, CA 9545 UPS/Fedex only
--
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only
Laytonville, CA 9545 UPS/Fedex only
