开云体育

Brian, I got a tube of Lube Gel from Radio Shack for $3 or $4. A 3 oz tube should last quite a long time. It claims Superior adhesion:stays where you put it, Non-toxic and Non corrosive, won't wash

If you have DSC encoders then its a good idea to get the delrin covers..they prevent the encoder cables from getting caught in the gears. "Brian Kennedy" <draco61@...> wrote: Herm Astropics

> I'm a new owner of a used G-11 (about 2 years old). I pretend to think > I've read through all the instructions (and previous threads here) and am > unable to find an answer to my problem. > >

I have a GM8 and some questions. 1) I am reading alot about tearing down and relubing the GM11. Is this something I should consider doing to my GM8? If so, what is the best lube to do this

indeed problem I Losmandy holds the paying are fairly

Thanks to all who contributed to advise on relubing the G-11. With Mark's and others advice, I decided to try this myself and did indeed find that all bearings on the RA & DEC were seized. The only

Steve: Thanks for your advise. Gretting Victor

Adair, I have a CG-11 with same setup except a ST-8 and Van Slyke Slider. I have and additional 11 Lbs. and have no problem with balance, even room to add some additional equipment if I wanted. I

Hello to all: At this moment I am buying a mount Losmandy G11 to place in this mount one telescope OTA Celestron 11 " with NGFS focuser and a DRO JMI, together with one camara CCD ST-9E and too the

My power cable broke when I tripped on the cable and the wires came out of the cigarette adapter.After having to do some soldering I just tied a small knot in the cord right before the wires exit the

Just a note here, (to get it off my chest, and because I know that Scott reads this occasionally :-) I absolutely love my G11. Fabulous piece of equipement. Built like a rock, and worth every penny.

the only encoders to get are the ones from Losmandy, other encoders interfere with the clutch operation..you can use any computer you like. Get the delrin encoder covers and route the cables neatly

Glenn, Any of the Tangent boxes will work but as far as the encoders are concerned the Losmandy encoder kit is the best for the mount. If you don't have the delrin gear covers, get them also. Don

I am the new owner of a G11 (in fact, it still hasn't been unboxed having just arrived). I have never even seen a G11, but I got one off astromart for a good price. At any rate somebody else found

This G11 addition looks great and works well. I bought a standard, 12' black good quality coiled phone cable and cut it into three pieces. One about half the length and one about 5" long (coiled

wrote: connectors (or complete cigarette lighter ready cables) with the screw down collar? ... The Radio Shack model uses a slightly larger plug (5.5mm I think), but it works fine - I picked up one

Yes. That's why I went back to the Allen-key bolts. Paul Sterngold --- Allen Maroney <amaroney@...> wrote: __________________________________________________ Do You Yahoo!? Yahoo! Mail - Free

I seem to have a slight bit of slop between the G11 head and the tripod pier. I'm using the TKS (no-tool tripod knobs) as tight as I can hand crank them. This is only noticable when there is

Hi there, I use a feeler guage and gradually increase space until the worm is free to turn the wheel gear with a little backlash. In RA a little backlash is OK since we only drive in one direction.

"steve ott" <steveo@...> wrote: Yes, you can push it by hand or slew it at 32x sidereal, the G11 has a top speed of 16x and it takes forever to slew. I often starhopped with an 8*50 finder