开云体育

I must have something wrong. 2022/02/14 17:29:42 Unable to get frequency from rig my-rig: dial tcp 127.0.0.1:4532: connect: connection refused. 2022/02/14 17:29:42 Starting HTTP service

This is a full BAP load on a Pi 4.

Duh!! I didn't even noticed Rig Control. Changed to Yes. I'll turn on the Xiegu G 90 and see if my 40 m Hamstick can connect to Ardop gateway. I always needed some one to look over my shoulder to make

Anything that uses OpenVPN can be done fairly easily. Don't know anything about that one you mentioned.

Anyone try to make the Virtual Shield VPN work with BAP? Really would prefer not to open my network up to the internet without this sort of protection. Thank you

The kit ships with ~68' of wire. -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack ) Twitter ( https://twitter.com/km4ack ) | Store (

make sure the rig is on and then reboot the Pi and see if that clears the issue. I have ran into this issue occasionally before if I boot the Pi before turning on the radio. -- 73, de KM4ACK YouTube (

Did you set rig control to "on" in Pat Menu Settings? -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack ) Twitter ( https://twitter.com/km4ack ) | Store

Did you load Pat Menu with Build a Pi or is this a custom/manual build? -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack ) Twitter (

[image: 2022-02-14-155821_1920x1080_scrot.jpg] I had to use scrot to create a screen cap and use Pat Winlink to send it to my email address so you can see what the issues are. I have Digirig running

I get: **** List of CAPTURE Hardware Devices **** with nothing listed.

Thanks Jason! I’m going to become a Patreon of your channel today!

This is the info I was looking for. Getting Pat Winlink to PTT using my Xiegu G 90. I have no issues with JS8CALL etc. 73 *Don PoapsNew Westminster, BC*VA7DGP DATA VA7QU VOICE *Winlink:

After configuring the Pat Menu with appropriate card and device number from arecord -l, I can perform "reboot" numerous times and the card and device numbers remain constant, and Pat Winlink works

I see this happen too. It seems to come and go randomly. I’ve been meaning to test with a different browser to see if it is a chrome issue. I’ve just got in the habit of clicking the x on refresh

I would think that you did make an error in winding. Mine was better then 1.5:1 on 40,20,15,10 AND 12 meters. 12 was a pleasant surprise. It’s a great kit and works perfectly with the SOTABEAMS

I am trying to set up WebRTC or similar to communicate voice (I have FT8, WSJTX, and JSCALL working) over IP.? I have a pi set up running for my IC 7300 that I would like to remotely key VOICE using

I think I have found the error in my winding. I will attempt a correction - if I can remove the hot glue ;-). For my information, about how long is the wire that comes with the kit? Thanks again for a

Your best bet is the check with the developer of FLMSG /g/linuxham/topics I haven't used FLMSG in a LONG time. -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (

It doesn't seem as though the Pi is "seeing" the sound card in the 705. What do you get if you run: *arecord -l * -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (