开云体育

also confirming if you are using the rear ports on the 817 you need to be in pkt mode not FM Wade VK1MIC

I have been attempting, relatively in vain, to be able to connect to Winlink over 2m. If I use the BAP Pat Menu to configure everything, once it brings up the mailbox, in the status at the bottom it

Been trying to get my 817 setup with packet radio (still only tech license) and for some reason if I do it all within the Pat Menu from BAP 3.0.6 or 3.05, it does not work at all. When I use the

https://youtu.be/0GlJiVrC3Wc Get Pat Menu working. Follow the APRS program setup using RFcomm0 I start by clicking on Pat Menu, Click on Mobilink (Beta) it finds the Mac address etc and starts

Ok not needing direwolf. Okay i will have do to some more looking

Just doing some preliminary research and brainstorming, but wondering if anyone has tried running Build-A-Pi on a newer Android phone (without root) using Termux.? I don't have an Android phone to

What sound card do you have selected in WSJT-X? For my 705 I selected the following which work for me: alas_input_usb-Burr-Brown... alas_outpot_usb-Burr-Brown... Also, I've heard of other folks having

FIY anyone running the X5105 and FLRIG v1.3.54 something has changed.? The only way I could get the rig and pi to play well together using FLRIG was to *set the rig as G90* and *NOT* X5105.? Baud

Jason gave me this advice when troubleshooting the signal link sound card. Double check the volume of the 705 on the pi is set to 100%. run "alsamixer" from the command line. F6 to select the sound

Scott I run Pat Menu. Click on Start Mobilink Bluetooth in the menu. I then either click on Yaac or Xlastir on the PI. In one of the videos Jason did. It's Serial I think for the TNC setting. I point

Hi Don I have now gotten a 64 GB USB3 disk loaded with the Raspian-12-11-20-i386 OS and was able to do BAP on it last night. I don't have everything loaded but do have GPS, Conky, and some two or

Hi Vic, To insure a clean build, I would recommend flashing the SD card again with Raspbian OS and then run BAP again. -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar (

Hi Ed, You are correct that the document is out of date and I have a warning right at the very top. However, if you used Build a Pi to install everything, there's no need for that document. BAP does

Jason, just got to Mobilink and I'm wanting to set it up with a Raspberry Pi for aprs or winlink I got the I got Pat menu to recognize it through the Mobilink connect but I'm trying to use it on aprs

After finishing I found it's a Windoze OS. I'm wondering if the Raspian Desktop OS would work. I have to do some research to see if they have a Linux version. 73 *Don Poaps* *New Westminster, BC*

Go to Winlink.org to Account and go to Account recovery. https://winlink.org/user Hope this helps 73 *Don Poaps* *New Westminster, BC* *VA7DGP DATA* *VA7QU VOICE* *Winlink: va7qu@...

That's a pretty old script designed for something specific. What are you trying to accomplish? -- 73, de KM4ACK YouTube ( https://youtube.com/km4ack ) | Tip Jar ( https://www.paypal.me/km4ack )

https://youtu.be/P9ua97I_zEY I'm whether it works with BAP 73 Don Poaps New Westminster, BC VA7DGP DATA VA7QU VOICE Winlink: va7qu@... Subject://wl2k ALLSTAR 530780 HH# 5971 HH# 11384

Good idea... I never tried VOX.? Thanks for passing this on. This is a USB CAT command issue within flrig. I contacted the flrig author (via the linuxham group), and they are working on a solution.

You've checked the obvious? If so, how did you test it?